thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
wear protective
refer to
clothing
instruction
manual
1.1.
general
Warning! ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using this
R
equipment, make sure you know where the nearest fire extinguisher is.
Warning! Always wear approved eye / face protection when operating the soldering iron.
R
Warning! Do not use the soldering iron if you notice damage to the workpiece.
R
Warning! Always point the soldering iron away from the eyes and body when during operation.
R
Warning! Do not put the soldering iron down, put it back in its holder.
R
Warning! Only use in a well ventilated area.
R
do not use the torch in an area where paint fumes, solvents or other flammable solids, liquids or gases pose a potential hazard.
Keep flammable material away from the torch when operating.
do not operate the soldering iron when you are tired or under the influence of alcohol, drugs or intoxicating medication.
do not hold any workpiece by hand.
do not touch the workpiece close to the heated area as it will be very hot. Allow to cool.
do not operate the soldering iron if it is damaged as this may cause failure and/or possible personal injury.
do not touch the top of the soldering iron during or immediately after use, as it will be very hot. Allow to cool.
do not allow children to operate the soldering iron.
When not in use, store away from direct sunlight in a safe, dry, childproof location.
do not store at over 40°C, such as in a car in hot weather.
do not leave battery in a discharged state, recharge battery immediately. before storage, fully
recharge the battery, subsequently recharge the battery at least once every six months
of non-use.
1.2.
electrical safety for use of charger.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING SOLDERING IRON TO THE POWER SUPPLY.
Warning! it is the user's responsibility to read, understand and comply with the following electrical instructions:
R
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(residual current device) is used with all electrical products, particularly portable equipment which is plugged into an electrical
supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3.
You must ensure that you:
inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply.
if worn or damaged do not use.
Important: Check that the voltage marked on the charger plug is the same as the soldering iron.
V
do not pull the charger plug from the mains socket by the lead.
Warning! do not use any other type of charger with this product, other than the supplied mains charger. Failure to observe
R
this warning could result in injury and or fire and will invalidate the warranty.
do not try to take the charger plug apart.
do not use the charger plug to charge or power any other electrical items.
do not get the charger wet, or use in wet, damp conditions (for indoor use only).
1.3
battery safety
Warning! To reduce the risk of burns or fire:
R
do not Attempt to open, disassemble, modify or service the battery pack.
do not Crush, puncture, short external contacts or dispose of in fire or water.
do not Expose to temperatures above 60°C (140°).
Replace only with the battery pack designated for this product.
© Jack sealey limited
instructions for
soldering iron rechargeable lithium-ion
sdl6
model no:
wear eye
warning:
protection
Hot surface
Original Language Version
sDL6 | Issue 1 17/06/15