Sealey CP1210 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. GENERAL SAFETY
Disconnect the grinder from the mains power before changing accessories, servicing or performing any maintenance.
9
Maintain grinder and discs in good condition. Check moving parts and alignment. If necessary use an authorised service agent.
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
9
warranty.
WARNING! Always work with the grinder's safety guard in place.
‰
Wear approved safety goggles, ear defenders, gloves and, if grinder generates dust, a dust mask.
9
Position the power cable clear of the grinding wheel to avoid cutting or snagging it. Hold grinder only by insulated gripping surfaces.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Use grinder in a suitable work area. Keep area clean, tidy and free from unrelated materials and ensure adequate lighting.
9
Maintain correct balance and footing, DO NOT over-reach. Ensure the floor is not slippery and wear non-slip shoes.
9
Use only approved grinding discs and only use the normal grinding surface.
9
Check grinding disc to ensure there are no splits, cracks or other damage (see Section 6). If in doubt DO NOT use the disc.
9
Grinding discs must be securely attached before use, but not over-tightened.
9
Secure unstable workpiece with a clamp, vice or other adequate holding device and ensure the grinder is gripped with both hands.
9
Keep non-essential persons away from the working area, use screens if necessary.
9
DO NOT operate the grinder if any parts are missing or the grinder is damaged.
8
DO NOT use the grinder for a task it is not designed to perform.
8
DO NOT operate the grinder where there are flammable solids, liquids or gasses.
8
WARNING! DO NOT grind any materials containing asbestos.
‰
DO NOT get the grinder wet or use in damp or wet locations.
8
DO NOT switch the grinder on whilst the disc is in contact with the workpiece.
8
DO NOT cover the grinder air vents. To do so will overheat the machine.
8
DO NOT touch the workpiece immediately after grinding, it will be very hot.
8
DO NOT use the grinder as a fixed tool and DO NOT try to cool the grinding disc with water or other lubricants.
8
DO NOT touch the grinding disc whilst operating, or whilst plugged into the mains power.
8
DO NOT leave the grinder running unattended, and DO NOT lay the grinder down whilst it is running.
8
DO NOT operate the grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
When not in use switch off grinder, remove plug from power supply and store in safe, dry, childproof area.
9
Use only approved grinding discs and only use the normal grinding surface. Never use the side or upper surface of disc for cutting.
9
The grinding disc may only be changed by a person holding a grinding wheel certificate.
9
Grinding discs must be securely attached before use, but not overtightened.
9
WARNING! The grinding process can produce streams of sparks which are a potential source of ignition, especially when
‰
grinding metal.
DO NOT use the grinder where there are flammable liquids, solids or gases.
8
DO NOT allow grinder sparks to make contact with the operator's clothing or any other fabric such as cleaning rags. Fabrics
8
contaminated with flammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant in
9
preference to man-made fibres.
2. INTRODUCTION
Compact, lightweight cordless mini angle grinder. Comfortable composite housing with soft grip to reduce vibration. Brushless motor allows
for a longer lasting tool requiring less maintenance. Spindle lock for easy disc changes. Built-in battery charge level indicator. Cutting disc not
included.
© Jack Sealey Limited
12V Ø76MM ANGLE GRINDER - BODY ONLY
MODEL NO:
Wear protective Wear safety
gloves footwear
Danger of fire/explosion hazard
Original Language Version
CP1210
Wear protective Wear ear
clothing protection
Wear a mask Wear
respiratory mask
(fumes)
CP1210 Issue 1 16/07/2020