Mitsubishi Electric 800 Series Instruction Manual page 18

Parameter list
Setting
Pr. Name
0 to 3600s,
762 Pre-charge ending time
9999
Pre-charge upper detection 0 to 100%,
763
level 9999
0 to 3600s,
764 Pre-charge time limit
9999
Second pre-charge fault
765 0, 1
selection
Second pre-charge 0 to 100%,
766
ending level 9999
Second pre-charge 0 to 3600s,
767
ending time 9999
Second pre-charge 0 to 100%,
768
upper detection level 9999
Second pre-charge time
769 0 to 3600s, 9999 9999
limit
Operation panel monitor 1 to 3, 5 to 14,
774
selection 1 17, 18, 20, 23 to
25, 34, 38, 40 to
Operation panel monitor
775
45, 50 to 57, 61,
selection 2
62, 64, 67 to 69,
Operation panel monitor 81 to 96,
776
selection 3
98,100, 9999
4 mA input check 0 to 590Hz,
777
operation frequency 9999
778 4 mA input check filter 0 to 10s
Operation frequency
0 to 590Hz,
779 during communication
9999
error
Acceleration time in 0 to 3600s,
791
low-speed range 9999
Deceleration time in 0 to 3600s,
792
low-speed range 9999
Pulse increment setting 0.1, 1, 10, 100,
799
for output power 1000kWh
Control method
800 9, 20, 109, 110 20
selection
820 Speed control P gain 1 0 to 1000%
Speed control integral
821 0 to 20s
time 1
822 Speed setting filter 1 0 to 5s, 9999
Torque control P gain 1
824 (current loop 0 to 500%
proportional gain)
Torque control integral
825 time 1 (current loop 0 to 500ms
integral time)
827 Torque detection filter 1 0 to 0.1s
828 Parameter for manufacturer setting. Do not set.
Speed control P gain 2 0 to 1000%,
830
9999
Speed control integral
831 0 to 20s, 9999 9999
time 2
832 Speed setting filter 2 0 to 5s, 9999
834 Torque control P gain 2 0 to 500%, 9999 9999
Torque control integral 0 to 500ms,
835
time 2 9999
837 Torque detection filter 2 0 to 0.1s, 9999 9999
Analog input offset
849 0 to 200%
adjustment
Terminal 4 function
858 0, 4, 9999
assignment
0 to 500A,
9999
Torque current/Rated
859
PM motor current
0 to 3600A,
9999
0 to 500A,
Second motor torque
9999
860 current/Rated PM
0 to 3600A,
motor current
9999
864 Torque detection 0 to 400%
Torque monitoring
866 0 to 400%
reference
867 AM output filter 0 to 5s
Terminal 1 function
868 0, 4, 9999
assignment
869 Current output filter 0 to 5s
Speed detection
870 0 to 5Hz
hysteresis
Input phase loss
872 0, 1
protection selection
874 OLT level setting 0 to 400%
Regeneration
882 avoidance operation 0 to 2
selection
Regeneration
883 avoidance operation 300 to 1200V
level
Regeneration avoidance
884 at deceleration detection 0 to 5
sensitivity
Regeneration avoidance
0 to 590Hz,
885 compensation frequency
9999
limit value
Regeneration
886 0 to 200%
avoidance voltage gain
888 Free parameter 1 0 to 9999
18
INVERTER FUNCTION SETTING
Initial
Pr.
range value
889 Free parameter 2
9999
Cumulative power
891 monitor digit shifted times 0 to 4, 9999
9999
892 Load factor
9999 Energy saving monitor
893 reference (motor
capacity)
0
Control selection during
894 commercial power-
9999
supply operation
Power saving rate
9999 895
reference value
896 Power unit cost
9999
Power saving monitor
897
average time
Power saving cumulative
898
monitor clear
9999
Operation time rate
899
(estimated value)
9999
900 CA terminal calibration ―
901 AM terminal calibration ―
9999
Terminal 2 frequency
902
setting bias frequency
9999
Terminal 2 frequency
902
0s
setting bias
903 Terminal 2 frequency
9999
(125) setting gain frequency
Terminal 2 frequency
903
setting gain
9999
Terminal 4 frequency
904
setting bias frequency
9999
Terminal 4 frequency
904
setting bias
1kWh
905 Terminal 4 frequency
(126) setting gain frequency
Terminal 4 frequency
905
25%
setting gain
Terminal 1 bias
0.333s
917
frequency (speed)
9999
917 Terminal 1 bias (speed) 0 to 300%
Terminal 1 gain
918
50%
frequency (speed)
918 Terminal 1 gain (speed) 0 to 300%
Terminal 1 bias
40ms
919
command (torque)
919 Terminal 1 bias (torque) 0 to 300%
0s
Terminal 1 gain
920
command (torque)
9999
920 Terminal 1 gain (torque) 0 to 300%
Current output bias
930
signal
Current output bias
9999
930
current
Current output gain
931
signal
9999
Current output gain
931
current
Terminal 4 bias
100%
932
command (torque)
932 Terminal 4 bias (torque) 0 to 300%
0
Terminal 4 gain
933
command (torque)

9999 933 Terminal 4 gain (torque) 0 to 300%
PID display bias

934
coefficient
PID display bias analog

934

9999 value
PID display gain

935

coefficient
150%
PID display gain analog
935
value
150%
Parameter copy alarm
0.01s 989
release
0
990 PU buzzer control
991 PU contrast adjustment 0 to 63

0.02s
992 Parameter for manufacturer setting. Do not set.
0Hz
997 Fault initiation
PM parameter
0
998

initialization
110%
Automatic parameter
999

setting
0
1000 Direct setting selection 0 to 2
Lq tuning target current
1002
adjustment coefficient
940VDC
1006 Clock (year)
0
6Hz
100%
9999
Setting Initial
Name
range value
0 to 9999 9999
9999
30 to 150% 100%
0.1 to 55kW

Inverter
capacity
0 to 3600kW

0 to 3 0
0, 1, 9999 9999
0 to 500, 9999 9999
0, 1 to 1000h,
9999
9999
0, 1, 10, 9999 9999
0 to 100%, 9999 9999
―
―
0 to 590Hz 0Hz
0 to 300% 0%
0 to 590Hz 60Hz
0 to 300% 100%
0 to 590Hz 0Hz
0 to 300% 20%
0 to 590Hz 60Hz
0 to 300% 100%
0 to 590Hz 0Hz
0%
0 to 590Hz 60Hz
100%
0 to 400% 0%
0%
0 to 400% 150%
100%
0 to 100% 0%
0 to 100% 0%
0 to 100% 100%
0 to 100% 100%
0 to 400% 0%
20%
0 to 400% 150%
100%
0 to 500.00,
9999
9999
0 to 300% 20%
0 to 500.00,
9999
9999
0 to 300% 100%
10 10
 
100 100
 
0, 1 1
58
0 to 255, 9999 9999
0, 8009, 8109,
0
9009, 9109
1, 2,10 to 13,
9999
20, 21, 9999
0
50 to 150%,
9999
9999
2000 to 2099 2000
Setting
Pr. Name
range
101 to 131,
201 to 229,
301 to 331,
401 to 430,
501 to 531,
601 to 630,
1007 Clock (month, day)
701 to 731,
801 to 831,
901 to 930,
1001 to 1031,
1101 to 1130,
1201 to 1231
0 to 59, 100 to
159, 200 to
259, 300 to
359,
400 to 459,
500 to 559,
600 to 659,
700 to 759,
800 to 859,
900 to 959,
1000 to 1059,
1100 to 1159,
1008 Clock (hour, minute)
1200 to 1259,
1300 to 1359,
1400 to 1459,
1500 to 1559,
1600 to 1659,
1700 to 1759,
1800 to 1859,
1900 to 1959,
2000 to 2059,
2100 to 2159,
2200 to 2259,
2300 to 2359
Running speed after
1013 emergency drive retry 0 to 590Hz
reset
Integral stop selection
1015 0 to 2, 10 to 12 0
at limited frequency
PTC thermistor
1016 protection detection 0 to 60s
time
Monitor with sign
1018 0, 1, 9999
selection
1020 Trace operation selection 0 to 4
1021 Trace mode selection 0 to 2
1022 Sampling cycle 0 to 9
Number of analog
1023 1 to 8
channels
1024 Sampling auto start 0, 1
1025 Trigger mode selection 0 to 4
Number of sampling
1026 0 to 100%
before trigger
Analog source selection
1027
(1ch)
Analog source selection
1028
(2ch)
Analog source selection
1 to 3, 5 to 14,
1029
(3ch)
17, 18, 20, 23,
24, 34, 40 to
Analog source selection
1030
42, 52 to 54,
(4ch)
61, 62, 64, 67,
Analog source selection
68, 81 to 96,
1031
(5ch)
98, 201 to 213,
230 to 232,
Analog source selection
1032
237, 238
(6ch)
Analog source selection
1033
(7ch)
Analog source selection
1034
(8ch)
1035 Analog trigger channel 1 to 8
Analog trigger operation
1036 0, 1
selection
1037 Analog trigger level 600 to 1400
Digital source selection
1038
(1ch)
Digital source selection
1039
(2ch)
Digital source selection
1040
(3ch)
Digital source selection
1041
(4ch)
1 to 255
Digital source selection
1042
(5ch)
Digital source selection
1043
(6ch)
Digital source selection
1044
(7ch)
Digital source selection
1045
(8ch)
1046 Digital trigger channel 1 to 8
Digital trigger operation
1047 0, 1
selection
1048 Parameter for manufacturer setting. Do not set.
1049 USB host reset 0, 1
1106 Torque monitor filter 0 to 5s, 9999
1107 Running speed monitor filter 0 to 5s, 9999
Excitation current
1108 0 to 5s, 9999
monitor filter
Initial
value
101
0
60Hz
0s
9999
0
0
2
4
0
0
90%
201
202
203
204
205
206
207
208
1
0
1000
1
2
3
4
5
6
7
8
1
0
0
9999
9999
9999