Important Safety Notice Proper service and repair is important to the safe, reliable operation of all DELL Company Equipment. The service procedures recommended by DELL and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended.
Page 3
1. Exploded view diagram with list of items...
Page 4
SE2416H Description Q'ty BEZEL LOGO DELL KEY_POWER KEY BOARD KEY_FUNCTION PANEL POWER BOARD MAIN BOARD Part No. Description Q'ty MAINFRAME Q01G6019 1 SCREW Button 0D1G1030 6120 SCREW D3 6 REAR_COVER 0M1G1140 6120 SCREW M4 6 REAR LOGO 0Q1G 130 6120...
3. Mechanical Instruction Tools Required List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed. Tool Description: - Phillip head Screwdriver - Hex Screwdriver - Penknife...
Page 7
3.1Disassembly Procedures: Step Figure Remark Turn off power, S1.Before Unplug external cables disassemble from product To remove the stand: Press the button on the red circle then pull out the stand follow the arrow, stand will be remove. S2.Remove the STAND-BASE Note: ASS’Y To prevent scratches on the LCD screen while removing the stand, ensure that the monitor is...
Use a Philips-head screwdriver to remove 2 screws for unlocking mechanisms. (No.1~2 screw size=M3x4; Torque=4±1kgf.cm) S3.Remove the REAR COVER Use Penknife to separate the bezel and rear cove follow the arrows in sequence, then you can take out rear cover. S4.Disconnect the FFC cable...
Use a hex screwdriver to remove 2 screws for S5.Remove the unlocking mainboard. (No.1~2 is Hex-screw, Torque= 4.5±0.5kgf.cm) S6.Remove the FFC cable S7.Remove the PAPER TAPE and panel FFC cable...
Page 10
S8. Remove the Remove and turn over it. MAIN FRAME...
Page 11
Use a Philips-head screwdriver to remove 5 screws for unlocking mainboard and power board (No.1~4 screw size=M4x8; Torque= 6±1kgf.cm; No.5 screw size=D3x6; S9.Remove the Torque= 6±1kgf.cm) MAIN &POWER BOARD disconnect the cables Use a Philips-head screwdriver to remove 4 screws for unlocking Key S10.Remove the board.
Page 12
Use a Philips-head screwdriver to remove 1screws for unlocking S12.Remove the screw main frame (No.1 screw size= Q3x6 Torque=4±1kgf.cm) S13. The MAIN FRAME S14.The BEZEL...
3.2 Assembly Procedures: Step Figure Remark Use a Philips-head screwdriver to tighten S1.Assembly the 1screws for locking main frame main fraim (No.1 screw size= Q3x6 Torque=4±1kgf.cm) Use a Philips-head screwdriver to tighten 4 screws for locking Key S2.Assembly the board.
Page 14
Use a Philips-head screwdriver to tighten 5 screws for locking mainboard and power board (No.1~4 screw size=M4x8; Torque= 6±1kgf.cm; No.5 screw size=D3x6; Torque= 6±1kgf.cm) S4. Assembly the Assembly the MAIN FRAME MAIN FRAME S5. Pasted the TAPEs and connect the panel FFC cable...
Page 15
S6.Connect the cables Use a hex screwdriver to tighten 2 screws for S7.Tighten he locking mainboard. VGA port (No.1~2 is Hex-screw, Torque= 4.5±0.5kgf.cm) S8.Connect the FFC cable...
Page 16
Assembly the Rear cover. Use a Philips-head screwdriver to tighten 2 S9.Assembly the screws for locking REAR COVER mechanisms. (No.1~2 screw size=M3x4; Torque=4±1kgf.cm) S10.Assembly the Insert the Stand Stand...