Sealey GSA634 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction Wear eye
manual protection
1. SAFETY
9 Follow all workshop safety rules, regulations, and conditions when using wrench.
9
9
9 9 WARNING!9Disconnect from air supply before changing accessories or servicing.
‰
9
9 Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Non-authorised parts
9
may be dangerous and will invalidate the warranty.
9 WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
9
9 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
9
9 9 Wear approved safety eye/face shield, ear defenders, and hand protection.
9
9
9 9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
9
9 9 Keep children and non essential persons away from the working area.
9
9
9 9 DO NOT use the wrench for a task it is not designed to perform.
9 8
9 WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
‰
9
9 DO NOT use wrench unless you have been instructed in its use by a qualified person.
9 8
9 DO NOT expose the comfort grip to excessive heat.
9 8
9 9 DO NOT carry the wrench by the air hose, or pull the hose from the air supply.
9 8
9 9 DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
9 8
9 9 DO NOT carry wrench with your hand on the power trigger in order to avoid unintentional starting.
9 8
9 9 DO NOT direct air from the air hose at yourself or others.
9 8
9 9 When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
9
2. INTRODUCTION
Generation Series twin pawl compact air ratchet wrenches. Feature packed, with contoured handle to insulate user from chill and vibration.
Finger operated trigger and textured grip allows added control, even with greasy hands. Low noise exhaust adjusts 360°, keeping airflow away
from operator. Four-position air regulator integrated into air inlet adjusts torque output. Ideal for working in engine bays or other places with
restricted access.
3. SPECIFICATION
MODEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . GSA634 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GSA635
Drive size . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"Sq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3/8"Sq
Max torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50lb.ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50lb.ft
Air consumption . . . . . . . . . . . . . . . . . . . . . . . . 5cfm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5cfm
Operating pressure. . . . . . . . . . . . . . . . . . . . . . 90psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90psi
Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.75kg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.75kg
Noise-Power . . . . . . . . . . . . . . . . . . . . . . .97.28dB(A) . . . . . . . . . . . . . . . . . . . . . . . . . . 97.28dB(A)
Noise-Pressure. . . . . . . . . . . . . . . . . . . . .86.28dB(A) . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.28dB(A)
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.3m/s² . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3m/s²
Uncertainty . . . . . . . . . . . . . . . . . . . . . . . . . .0.56m/s² . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.56m/s²
4. PREPARATION
4.1. Air Supply. (Recommended hook-up procedure is shown in fig 1.)
4.1.1. Ensure wrench air valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the wrench. Too high an air pressure and unclean
‰
air will shorten the product life owing to excessive wear, and may be dangerous, causing damage and/or personal injury.
4.1.3. Drain the air tank daily. Water in the air line will damage the wrench.
4.1.4. Clean air inlet filter weekly.
4.1.5. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
4.1.6. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
© Jack Sealey Limited
GENERATION SERIES COMPACT AIR RATCHETS
1/4" & 3/8" DRIVE
GSA634, GSA635
:
MODEL NO'S
Wear protective
Wear ear
gloves
protection
Original Language Version
GSA634, GSA635 Issue: 5(HF) - 22/05/18