Related Manuals for LG STB-6500
Summary of Contents for LG STB-6500
- Page 1 INSTALLATION MANUAL Please read this manual carefully before operating your set and retain it for future reference. STB-6500 *MFL71757901* www.lg.com Copyright © 2020 LG Electronics Inc. All Rights Reserved. (2007-REV00)
-
Page 2: Table Of Contents
Installation Menu Settings - Portal Manager Media Share Installation Menu - Smart Share - Screen Share Introduction - Media Renderer LG Hotel Mode Setup - DIAL - Power On Status - STB Name - Volume - SoftAP - Key Management - Beacon... - Page 3 IR Codes External control device Setup RS-232C Setup Phone jack Type Type of Connector : D-Sub 9-Pin Male RS-232C Configurations Communication Parameters IR OUT Using Guide - Suitable / Not Recommend remote-controller data format - IR Receiver specifications Command Reference List Transmission / Receiving Protocol...
-
Page 4: First Use Wizard
First Use Wizard * Images shown may differ from your STB. Screen Resolution The first time you turn ON the STB/display panel, a prompt to select the screen resolution will be displayed, and you will need to select the appropriate option — 2160p, 1080p, 720p, 1366 x 768 — for the STB’s video output format. You cannot proceed with STB configuration until you make a selection. -
Page 5: Basic Settings
(Depending on model) • There are four options - Basic Settings, Data Cloning, Solution Settings, and Installation Menu Settings. Each menu can access by Start button. Basic Settings (Depending on model) This menu is for basic settings related to language, network, portal, voice service coverage and programme tuning without SI (Pro:Centric) setting. There are four steps for it. -
Page 6: Network Settings
Network Settings (Depending on model) • Set Network connection. You can connect easily to wired/wireless network. (“Network Settings” on page 24) Wireless (Auto Wi-Fi) : Connect a default hidden SSID/PW. (SSID : lgwebostv, PW : procentric, Security : WPA/WPA2 PSK) -
Page 7: Portal Settings
Portal Settings (Depending on model) • Set the Portal Mode and Portal Auto Start. Portal Mode (Depending on model) • You can select ‘Default Portal’ (Use webOS default portal), ‘Customizable Portal’ (Use editable Portal), or ‘None’ (Do not use portal). Portal Auto Start •... -
Page 8: Voice Service Coverage
Voice Service Coverage (Depending on model) • Set the voice service coverage. You can set LG Service Country and Service Area Postcode(Depending on model) for voice service. -
Page 9: Data Cloning
Data Cloning (Depending on model) Access Data cloning menu of STB Manager application for applying cloning file. Solution Settings (Depending on model) The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions. The default Domain “procentric.local” and IP Server Address are needed to be registered in DNS STB will contact the IP Server using the default Domain “procentric.local”... -
Page 10: Automatically For Setup
Automatically for Setup (Depending on model) From the STB Configuration Options screen, you can choose how to proceed with the configuration of this STB. Whether you will configure the STB for Pro:Centric operation via the wizard or use a USB memory device to configure the STB, you may first wish to set the Room Number on the STB. - Page 11 • If you intend to apply the files via USB, use USB Configuration option to access STB Manager app. (“STB Manager” on page 46) • If you intend to set network, use the Network Settings option. You can connect easily to wired/wireless network by this option. (“Network Settings” on page 24) Wireless (Auto Wi-Fi) : Connect a default hidden SSID/PW.
- Page 13 This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data programme, select the Next.
- Page 14 Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 15: Manually For Setup
Manually for Setup (Depending on model) Select a Label and/or enter the Room Number using the numeric keypad on the remotes or using the virtual keyboard on the STB screen. To continue, move and select Next. Please select the Manual Pro:Centric. - Page 16 Configure the appropriate Pro:Centric settings in the STB. (RF varies depending on model.)
- Page 17 Downloading the Pro:Centric application files takes few minutes.
-
Page 18: Installation Menu Settings
After the installation is completed, the following screen will be displayed. Installation Menu Settings (Depending on model) Access Installation menu for commercial feature settings. -
Page 19: Installation Menu
The abundant functions for Hotel STB linked with software installation can be projected on OSD as ‘Installation Menu’ . The wide range of hotel features can be performed simply on additional window to enhance the LG hotel STB’s easy installation and convenient operation for Hotelier and System Integrators. -
Page 20: Lg Hotel Mode Setup
LG Hotel Mode Setup When ‘LG Hotel Mode Setup’ is set to On, all functions of Hotel Mode apply. Power On Status • Decide to select working status of STB Set when turn on main power. • You can select PWR, STD, LST. -
Page 21: Volume
- When selected to 'On' , if the value is larger then the maximum specified in the maximum volume entry, the maximum volume value must be used. - Access to a volume in ‘Timer Power On’ must be fixed to start volume when ‘LG Hotel Mode Setup’ (On) and ‘Start Volume’ (Off, 0 ~ 100) were set simultaneously. -
Page 22: Limited Mode
Limited Mode • Configure TV function’ s limitation. When selected to ‘On’ , following sub-menus will be worked by below. Setup Menu (Depending on model) • Permit to tune and manage programmes. Programme Change (Depending on model) • Decide to change programme or not. Menu Display •... -
Page 23: Power On Default
Power On Default • Set the programme to display, etc. when turn on power. • When set to Off, it is not applied to the subordinate Input, Programme, A/V Setting, Aspect Ratio menu. • When set to On, it can set by entering the subordinate menu. Input •... -
Page 24: Network
Network (Depending on model) MAC Address • Displays the MAC address (not customizable). Network Settings One-click network connection • Connects easily to a network. • This menu supports to connect to an available network. To connect to a network through Set Expert •... -
Page 25: Lg Connect
LG Connect (Depending on model) • Sets the 'LG Connect' function to On or Off. - You can connect STB via 'LG TV Plus' app in smart device. - Default setting is 'On' . IP Stream Control (Depending on model) Audio PTS Offset •... -
Page 26: Pro:centric
Pro:Centric (Depending on model) Mode • Sets whether or not enable Pro:Centric and the service method. • You can set to Off, Configuration Only, GEM or HTML. The default value is Off. WORF • When set to ‘Enable’ , Hour and Minute items are enabled and then the WORF function is enabled. •... -
Page 27: Receive Data
• P:C IP Setting - Server Address is set to IP Address. - Can select IPv4 or IPv6 type using 'IP Type' . (Depending on model) (IP Address) Set IPv4 or IPv6 address. (Port Number) Sets the actual port or number where the Pro:Centric server is running. - Server Address is set to Domain Name. -
Page 28: General
General Configuration Setup Select RCU • It is a mode to set whether to use Select RCU or not. When set to ‘Enable’ , You can adjust ‘Number of RCU’ menu. Number of RCU • Number of RCU value range 1~9. (When ‘Select RCU’ is set to ‘Enable’) •... - Page 29 One Channel Map (Depending on model) • If set to ‘Enable’ , the STB will operate as below. - A. When the STB is auto-scanning, it searches both air and cable channels. - B. User can assign a channel number him/herself by manual scan. - C.
- Page 30 Radio Name Display (Depending on model) • Instead of “Audio Only”, the name of a radio programme is displayed on the screen when a radio broadcast is playing. • If the setting is “On”, the name of a radio programme is displayed for the radio programme. •...
- Page 31 InStant On (Depending on model) • Set to ‘Instant On Mute Mode’ or ‘Instant On Reboot mode’ to enable the Instant On feature. The Instant On feature allows the STB to turn On when AC power is applied, but with video and audio muted (Muted On). The STB retains its On status while appearing to be Off. Pressing the POWER button toggles Off/On the video and audio mutes, so that the STB appears to turn On instantly.
- Page 32 • You can configure the Sound Out to be set after power on. • You can select Off, TV Speaker, Optical, LG Sound Sync., HDMI ARC • If you set this option to Off, the STB maintains Sound Out after power on.
-
Page 33: External Speaker / Line Out
External Speaker / Line Out (Depending on model) Volume Control • Selects the volume control method of an external speaker. • You can select ‘Off’ , ‘Int Variable’ Fixed. (Depending on model) • Int variable is linked to the main volume OSD and change the volume 0 - 2 Watts. •... -
Page 34: Hcec Setup
• You will have 3 modes to choose [Default], [HCEC] and [TVLink-CEC]. • If [Default] is selected, you can use SIMPLINK which is provided in LG STB. Also you can enable and disable SIMPLINK through SIMPLINK MENU. • If [HCEC] is selected, you can use TVLink-HCEC Protocol. (For more detailed information, please refer to TVLink-HCEC Protocol document) •... -
Page 35: Clock Setup
Clock Setup (Depending on model) Mood Display Setup (Depending on model) • You can setup Mood Display features. Clock Source • You can select ‘Off’ , ‘Pro:Centric’ , ‘TV’ , ‘NTP’ , ‘Admin’ . • NTP : Clock is synchronized using Network Time Protocol. It's only enabled when network cable is connected. •... -
Page 36: Developer Mode
Developer Mode (Depending on model) • This feature provides great convenience to the app developers. • Set up to install the Developer mode app. Security Port Control (Depending on model) • Unused ports can be blocked for network security. Lock Mode •... -
Page 37: Portal Settings
STB Information • You can check the STB information. Check Items • You can Inspect the STB status. STB Manamer Password Protection • You can set password for protect access to STB Manager. • When STB Manager password protection is activated, the password is required for access to STB Manager. Portal Settings (Depending on model) Portal Mode... -
Page 38: Website Shortcut
Website Shortcut (Depending on model) Shortcut • Sets Enable or Disable. When it is set to Enable, Website Shortcut app is displayed at launcher bar. Shortcut Name • You can set Website Shortcut app name (title). Shortcut URL • Sets URL to connect when excute Website Shortcut app. Shortcut Icon •... -
Page 39: Hotel Directory
Hotel Directory (Depending on model) • Set the information to display at Hotel Directory app. Facility or Service Name • Set the facility or service name. Details or Extension • Set the detailed information. Related Photo • You can select None, downloaded images or Download (Go to STB Manager). •... -
Page 40: Portal Manager
Portal Manager (Depending on model) This feature enables you to group together multiple monitor sets on a single network into the same group and copy portal setting data on a group basis. This feature has two modes, Master and Slave. Master •... - Page 41 Group Management • Creating a New Group Click Add New Group. Enter a group name. Click Add Device, select the devices you wish to add to the group, and add them. Click Done, and you will see that a new group has been created. •...
-
Page 42: Media Share
Media Share (Depending on model) Smart Share (Depending on model) • Smart Share enables DLNA function. If this value is enabled, STB acts as Media Player and displays Media Server contents through Smart Share app. Screen Share (Depending on model) •... -
Page 43: Softap
SoftAP (Depending on model) • SoftAP is similar to Access Point. When you enable this function, STB acts as an Access Point. • Regardless of the Instant On mode, the SoftAP setting stays unchanged after power off/on. (Depending on model) Use Default •... -
Page 44: Beacon
Beacon (Depending on model) • This option enables BLE Beacon, one of Bluetooth 4.0's features. • Beacon Mode (On/Off Toggle): enables the Beacon feature. • The iBeacon/Eddystone Type Beacon features are supported. iBeacon • Beacon UUID (hex): Set the UUID. Field1: 4byte hex value (8 digits) Field2: 2byte hex value (4 digits) Field3: 2byte hex value (4 digits) -
Page 45: Display
Display Resolution • You can set the STB resolution. Display On Time Setup • STB will send command set to display monitor after delay time(seconds) which is set in Display On Time Setup menu. HDMI Input Setup • Menu for setting external input values to show at screen •... -
Page 46: Stb Manager
STB Manager * Images shown may differ from your STB. You can update files from USB to STB through the STB manager. Diagnostics (Depending on model) • Sets Enable or Disable. When it is set to Disable, user can’t control STB via RMS. The changed setting is applied after reboot. - Page 47 Ez Download • Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL, Media files, Micom, Pro:Idiom M Key. (Depending on model) - Images, Icon, Pro:Idiom M Key file and Software Update files should be copied into the folder named LG_DTV on the USB. »...
- Page 48 • Press button to display storage usage information. • Press the “Clear Storage” button to delete the downloaded media files.
- Page 49 Import Clone File • Once the internal STB data and its programme map information are written to the USB memory card, the user can start “Import Clone File” process with the data file generated and stored in USB memory card. The user should not turn STB off nor unplug the USB memory card while processing. The following reference images might be slightly different.
- Page 50 Export Clone File • “Export Clone File” creates “TLL” file in USB root folder. “TLL” file can be used to “Import Clone File”. While writing is in process, the user must not turn STB off nor unplug the USB memory card. The following reference images might be slightly different.
-
Page 51: Usb Download Menu
USB Download Menu USB Cloning • An Installation can quickly set up and clone multiple STB sets at a property. These cloned STBs will all have the same Master STB Setup: Installation Menu settings, User A/V settings and the programme Map. This newer procedure significantly decreases the installation time that would be necessary if the standard RS-232C method were used instead. - Page 52 Image Download (Depending on model) • The download sequence is Image Download Select Image(s) Download. • The target file is located in LG_DTV folders. • Press the "Clear Storage" button to delete the downloaded images. - Apps Background Image(s), No Signal Image(s), Hotel Directory Image(s) (Depending on model) »...
- Page 53 Icon Download (Depending on model) • Images is located in LG_DTV folder. • If you updates the images, original images will be removed. • The download sequence is Icon Downalod Select Images Download. • Icon Image can download only one file. •...
- Page 54 Video Download (Depending on model) • Media files is located in LG_DTV folder. • The download sequence is Video Download Select media file Download. • Media files can only download one file each. • If you updates the video file, original file will be removed. •...
- Page 55 Software Update ► Update STB Software • This feature updates STB software through the EPK file in USB. • The target file is located in LG_DTV folder. • The download sequence is Software Update Update STB Software Select file(EPK) Update. ►...
-
Page 56: Ir Codes
IR Codes • This feature is not available for all models. Code Code Function Note Function Note (Hexa) (Hexa) Remote control Button Remote control Button (POWER) (Power On/Off) Remote control Button Remote control Button (Q. Settings) Remote control Button (BACK) Remote control Button Remote control Button Remote control Button... -
Page 57: External Control Device Setup
External control device Setup Phone jack Type (Depending on model) (TV) (PC) RS-232C Setup • You need to purchase the phone-jack to RS-232C cable required for RS-232C IN the connection between the PC and the STB, which is specified in (CONTROL &... -
Page 58: Rs-232C Configurations
RS-232C Configurations IR OUT Using Guide Suitable / Not Recommend remote-controller data format 7-Wire Configurations (Standard RS-232C cable) Item Formats Suitable data format NEC, RC5, Toshiba Continuous data format Not recommend data format (short burst/gap signal) IR Receiver specifications Carrier frequency 37.9 KHz Peak Wavelength 940 nm... -
Page 59: Command Reference List
IR output signals will be suppressed automatically by IR receiver. (Depending on model) • In this case, LG does not guarantee IR working function. • To make sure of this matter, here are two methods as below. Data - Use the remote-controller with suitable data... -
Page 60: Transmission / Receiving Protocol
Transmission / Receiving Protocol 1 Power (Command: k a) ► To control Power On/Off of the set. (Depending on Model) Transmission [k][a][ ][Set ID][ ][Data][Cr] Transmission Data 00 : Off [Command1][Command2][ ][Set ID][ ][Data][Cr] Data 01 : On [Command1] : First command to control the STB. (j, k, m or x) [Command2] : Second command to control the STB. - Page 61 3 Screen Mute (Command: k d) 6 Contrast (Command: k g) ► To select screen mute on/off. ► To adjust screen contrast. You can also adjust contrast in the picture settings. Transmission Transmission [k][d][ ][Set ID][ ][Data][Cr] [k][g][ ][Set ID][ ][Data][Cr] Data 00 : Screen mute off (Picture on) / Video mute off Data 01 : Screen mute on (Picture off) Data Min : 00 to Max : 64...
- Page 62 10 Sharpness (Command: k k) 14 Colour Temperature (Command: x u) ► To adjust the screen sharpness. ► To adjust Colour Temperature. You can also adjust Colour Temperature in You can also adjust sharpness in the picture settings. the picture settings. Transmission Transmission [x][u][ ][Set ID][ ][Data][Cr]...
- Page 63 16 Auto Configuration (Command: j u) (Only RGB support model) 18 Tune Command (Command: m a) ► To adjust picture position and minimize image shaking automatically. It ► Select channel to following physical number. works only in RGB (PC) mode. Transmission Transmission [m][a][ ][Set ID][ ][Data 00][ ][Data 01][ ][Data 02][Cr]...
- Page 64 21 Control Backlight (Command: m g) * Real data mapping ► To control the backlight. 00 : Step 0 Transmission Step 10 (Set ID 10) [m][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Step 15 (Set ID 15) 10 : Step 16 (Set ID 16) [g][ ][Set ID][ ][OK/NG][Data][x]...