Table of Contents
Advertisement
Quick Links
48in, 52in, or 60in Recycler
TITAN
Model No. 126-8701
Model No. 126-8702
Model No. 126-8703
Model No. 133-2166
Model No. 133-2167
Model No. 133-2168
This product contains a chemical or chemicals known to the State of California to
Safety
Using the Side-Discharge
Mode or Mulching Grass
WARNING
Without the grass deflector, discharge cover, or
complete grass catcher assembly mounted in
place, you and others are exposed to blade contact
and thrown debris. Contact with rotating mower
blade(s) and thrown debris will cause injury or
death.
• Never remove the grass deflector from the mower
because the grass deflector routes material down
toward the turf. If the grass deflector is ever
damaged, replace it immediately.
• Never put your hands or feet under the mower.
• Never try to clear the discharge area or mower
blades unless you disengage the power-take-off
(PTO) lever and turn the ignition key to off.
Also remove the key and pull the wire off the
spark plug(s).
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
HD 1500, 2000, or 2500 Series Riding Mower
WARNING
CALIFORNIA
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Register at www.Toro.com.
Form No. 3406-569 Rev B
®
Kit
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3406-569* B
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro Recycler 126-8701
Summary of Contents for Toro Recycler 126-8701
- Page 1 (PTO) lever and turn the ignition key to off. Also remove the key and pull the wire off the spark plug(s). © 2016—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3406-569* B...
-
Page 2: Table Of Contents
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. – No parts required Remove the existing blades. – No parts required Remove the existing baffle. Discharge plate Carriage bolt (5/16 x 7/8 inch) Flange nut (5/16 inch) - Page 3 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Move the motion-control levers to the N position. EUTRAL 3. Set the parking brake. 4. Shut off the engine and remove the key. 5. Thoroughly clean the mower deck. Remove all debris to ensure that the baffles will fit properly. 6.
-
Page 4: No Parts Required
g017443 Figure 2 4. Blade bolt 1. Sail area of blade 2. Blade 5. Spindle-shaft end (hex end shown) 3. Curved washer Removing the Existing Baffle No Parts Required Procedure 1. Remove the flange nuts holding the baffle in place (Figure 2. -
Page 5: Discharge Plate
Installing the Discharge Plate Parts needed for this procedure: Discharge plate Carriage bolt (5/16 x 7/8 inch) Flange nut (5/16 inch) Flange nut (3/8 inch) Carriage bolt (3/8 x 1 inch) Procedure 1. Install the discharge plate to the outside of the mounting bracket with 2 carriage bolts (3/8 x 1-1/4 inches) and 2 flange nuts (small flange) (3/8 inch) as shown in... -
Page 6: Left Baffle
2. Loosely install the right baffle to the discharge plate with 1 carriage bolt (3/8 x 1 inch) and a flange nut (3/8 inch) as shown in Figure 3. Loosely install the right baffle to the top of the mower Installing the Baffles 48-inch deck with 1 carriage bolt (3/8 x 1 inch) and 1 flange nut, (3/8 inch) as shown in... - Page 7 (3/8 inch) as shown in Figure 8. Refer to Figure 6 Figure 7 for the correct holes to use. Figure 6 48-inch mower deck shown 1. Use these holes for 48-inch mower decks Figure 7 52-inch mower deck shown 1. Use these holes for 52-inch mower decks 9.
- Page 8 Figure 8 1. Right baffle 3. Left baffle 5. Center baffle 2. Carriage bolt (3/8 x 1 inch) 4. Flange nut (3/8 inch) 5. Position the left baffle into the mower. 6. Loosely install the left baffle to the top of the mower deck with 1 bolt (3/8 x 1 inch) and 1 flange nut (3/8 inch) as shown in Figure...
- Page 9 Figure 9 60-inch mower deck shown 1. Carriage bolt (3/8 x 1 inch) 2. Left baffle 3. Flange nut (3/8 inch) 4. Right baffle 11. Loosely install the center baffle to the right baffle with 1 carriage bolt (3/8 x 1 inch) and 1 flange nut (3/8 inch) as shown in Figure 12.
-
Page 10: Recycler Blades
Figure 11 1. Carriage bolt (3/8 x 1 inch) 3. Center baffle 5. Right baffle 2. Flange nut (3/8 inch) 4. Left baffle Installing the New Blades Parts needed for this procedure: Recycler blades Procedure Important: The sail part of the blade (i.e., the turned-up section) must face the inside of the mower (Figure 12). - Page 11 After Operating To ensure optimum performance, clean the underside of the mower housing after each use. If residue builds up in the mower housing, cutting performance decreases. Tightening all Fasteners No Parts Required Procedure 1. Tighten all nuts and bolts for the baffles (Figure Figure Figure...