7.3 : –1 UHE (Ultra High Efficiency) 150 W About 3000 hours V13H010L17 32.8 feet (10 meters) Alkaline AA (2) 4.1 inches (104 mm) 13.7 inches (348 mm) 10.8 inches (274 mm) 9.3 lb (4.2 kg) EPSON PowerLite TW100 Projector - 1...
Page 2
MAC19 MAC21 TV480i TV575i SDTV480p SDTV575P HDTV720p HDTV1080i NTSC4.43 M-PAL N-PAL PAL60 SECAM * The image is resized to display in one of the projector’s native formats. 11/02 Resolution DVI support Supported Supported Supported Supported Supported Supported Supported Supported Supported...
** This connection is not possible for models that are not equipped with a VGA output port. ESC/VP21 Commands When the projector is in a command ready state, it returns the code. When command processing is complete, the projector also returns a code.
Choose Rear/Ceiling for the Projection option. If the projector is tilted in the front or the back, you may need to adjust its shape. See page 9. Image Size and Projection Distance The distance between the projector and the screen determines the basic size of the projected image, as shown below.
4. If you want to turn the projector on again, wait until the light stops flashing red. Then press the 5. If you will not be using the projector for an extended period of time, make sure the power light is orange, then turn off the main switch on the back of the projector.
Page 7
Simulscan resolution settings. Click the then select a Simulscan resolution from the ones in the Resolution box. (Allow a few seconds for the projector to sync up after making the selection.) If you’re using a Macintosh laptop with OS X:...
Switching Between Picture Sources If the projector is connected to more than one video source, you can use the buttons on the control panel or remote control to switch between the different sources. On the projector’s control panel, press the display the currently selected source.
Adjusting the Image Shape If the projector is raised in the front or the back, like this: the projected image may not be square or rectangular; it may have a “keystone” shape like one of the examples shown below.
Standard images have an aspect ratio of 4:3 and HDTV images have an aspect ratio of 16:9. If your video source is 16:9, the projector displays it in its native ratio. If it is 4:3, you can choose the best mode for projecting it.
Note: You can make the blank screen blue, instead of black, or display the EPSON logo on the screen whenever you press the button. Freezing the Action...
Test Pattern button Illumination button Menu button Aspect button Auto button Still button Help button 12 - EPSON PowerLite TW100 Projector This table summarizes the functions on the remote control. Button Pattern Power Select (pointer button) Colortune Blank Input buttons Memory buttons (1–6)
Cleaning the Projector and Replacing Parts Warning: Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely.
If the dirt is difficult to remove or the filter is broken, replace it. Contact your dealer or call EPSON at (800) 873-7766 in the United States to obtain a new one. In Canada, please call (800) 463-7766 for dealer referral.
9. Reset the lamp timer as described in the next section. Resetting the Lamp Timer After you install a new lamp, you need to reset the timer so the projector can keep track of how many hours it has been used. Follow these steps: Menu 1.
DVI to analog video, 10 feet (3 meters) You can purchase these accessories from your dealer or by calling EPSON at (800) 873-7766; or visit the EPSON Store at www.epsonstore.com (U.S. sales only). In Canada, please call (800) 463-7766 for dealer referral.