1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Intercom System
  5. VL-SV74BX
  6. Service manual

Panasonic VL-SV74BX Service Manual

Video intercom system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Video Intercom System
VL-SV74BX
Model No.
VL-SV74CX
VL-SV74AZ
VL-SV74ML
VL-SV74SX
VL-SV74VN
VL-SV74VNP
VL-MV74BX
Model No.
VL-MV74CX
VL-MV74AZ
VL-MV74ML
VL-MV74SX
VL-MV74VN
VL-MV74VNP
VL-V524LCE
Model No.
VL-V524LSX
VL-V524LVN
VL-MB524BX
Model No.
VL-MB524SX
VL-MB524VN
-S:
Silver version
-W:
White version
(BX for Asia, Middle Near East and Africa)
(CX for Middle East and Africa, Hong Kong, Singapore)
(AZ for Australia and NewZealand)
(ML for Malaysia)
(SX for India)
(VN/VNP for Vietnam)
© Panasonic Corporation 2019
Unauthorized copying and distribution is a violation of law.
Order No.KMA1904116CE

Advertisement

Table of Contents
loading

Related Manuals for Panasonic VL-SV74BX

Summary of Contents for Panasonic VL-SV74BX

  • Page 1 (BX for Asia, Middle Near East and Africa) (CX for Middle East and Africa, Hong Kong, Singapore) (AZ for Australia and NewZealand) (ML for Malaysia) (SX for India) (VN/VNP for Vietnam) © Panasonic Corporation 2019 Unauthorized copying and distribution is a violation of law.

  • Page 3: Table Of Contents

    Table of Contents Page Page 1. Safety Precautions............5 10.1.3. How to Remove the Main Board, Speaker and LCD [No. 3]....................43 1.1. For Service Technicians............5 10.1.4. How to Remove the Power board, Key board [No.4]..44 1.2. Insulation Resistance Test (by Insulation resistance tester).....................5 10.2.
  • Page 4 14.2.1. Main Board..............76 15.1.3. Accessories and Packing Materials Location....80 14.2.2. MIC Board..............77 15.2. Replacement Parts List.............84 15. Exploded View and Replacement Parts List....78 15.2.1. Main Monitor Station............. 84 15.1. Exploded View..............78 15.2.2. Door Station..............93 15.1.1. Main Monitor Station............. 78 15.2.3.

  • Page 5: Safety Precautions

    1 Safety Precautions 1. Before servicing, unplug the power cord to prevent an electrical shock. 2. When replacing parts, use only manufacturer’s recommended components for safety. 3. Check the condition of power cord. Replace if wear or damage is evident. 4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc. 5.

  • Page 6: Warning

    2 Warning 2.1 Battery Caution Risk of explosion if battery is replace by an incorrect type. Dispose of used batteries according to the instructions. 2.2 About Lead Free Solder (PbF: Pb free) Note: In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that contains lead.

  • Page 7: Discarding Of P.c. Board

    For the purpose of recycling to facilitate effective utilization of resources, please return this product to a nearby authorized collection center, registered dismantler or recycler, or Panasonic service center when disposing of this product. Please see the Panasonic website for further information on collection centers, etc.

  • Page 8: Specifications

    3 Specifications Design and specifications are subject to change without notice. 3.1 Main monitor station (VL-MV74) Power source: 220-240 V AC, 50/60 Hz Power consumption: Standby: 2.3 W During operation: 11.3 W Dimensions (mm): Approx. 158 x 201 x 25 (excluding protruding sections) (height x width x depth) Mass (Weight): VL-MV74BX/VN: approx.

  • Page 9: Technical Descriptions

    4 Technical Descriptions 4.1 Block Diagram The block diagram of Video intercom system is shown in Fig 4.1. Image signal root: The image data is converted into NTSC signal by Camera unit, and the NTSC signal is modulated into FM signal. FM signal is sent to the Monitor station through the interphone cable with ASK signal which modulated from command signal and voice signal.
  • Page 10 Call Signal from Door station: When the call button is pressed in Stand-by mode, the short between lines causes the DC voltage of the interphone cable to go down. The monitor station detects this voltage reduction and then rings. Then LCD of the Monitor station is turned ON. Fig.

  • Page 11: Ic Operation

    4.2 IC Operation 4.2.1 Monitor Station Section 4.2.1.1 Main Monitor station Diagram - 11 -...
  • Page 12 4.2.1.2 Main Board 4.2.1.2.1 External Interface Part Regulator for 5V (IC671) Regulator for Power 5V (IC910) Input voltage: +12V Input voltage: +12V Output voltage: +5V Output voltage: +5V Package: 5pin SOT-25A. Package: 8pin SOP-8 Outline of Operation: It generate from +12V to +5V (FM Outline of Operation: It generate from +12V to +5V.
  • Page 13 4.2.1.2.2 Audio Part EEPROM(IC401) Sub CPU (IC405) Operating Power Supply : +3.3V Operating Power Supply : +3.3V Package: SOP-J8 Operating Power Supply : +4V (SP AMP) Memory capacity: 64kbit Operating Power Supply : +3.2V (RF) Outline of Operation: Storing the parameter of IC405. Operating Power Supply : +1.8V (Core) Package: 206pin 1MSRAM (IC404)
  • Page 14 4.2.1.3 Power Board 4.2.1.3.1 Power Supply Part Power control IC (IC1) Input voltage: AC 220V~240V Output voltage: DC 23V, DC 12V Package: 8pin DIP Outline of Operation: It generate from AC 220V~240V to DC 23V, DC 12V. 4.2.1.4 KEY Board 4.2.1.4.1 Key Part Regulator for Power 3.3V (IC1001) Input voltage: +5V Output voltage: +3.3V Package: 5pin SOT-89-5...

  • Page 15: Door Station Section

    4.2.2 Door Station Section 4.2.2.1 Door station Diagram - 15 -...
  • Page 16 4.2.2.2 Main Board Call Button (SW301) Outline of Operation : When a visitor presses the Call Button, a chime tone will ring at the monitor station. FM Signal Modulator (IC200) Operating Power Supply : +5V (+5V : 2, 9pin) Package : 24pin SOP Outline of Operation : The frequency modulation of the video signal taken in from Camera Unit is carried out.

  • Page 17: Location Of Controls And Components

    5 Location of Controls and Components Refer to the Operating Instructions. Note: You can download and refer to the Operating Instructions (Instruction book) on TSN Server. - 17 -...

  • Page 18: Installation Instructions

    6 Installation Instructions Refer to the Operating Instructions. Note: You can download and refer to the Operating Instructions (Instruction book) on TSN Server. - 18 -...

  • Page 19: Operating Instructions

    7 Operating Instructions Refer to the Operating Instructions. Note: You can download and refer to the Operating Instructions (Instruction book) on TSN Server. - 19 -...

  • Page 20: Service Mode

    8 Service Mode 8.1 Things to do after replacing IC If repairing FLASH Memory, EEPROM, it is necessary to initialize and adjustment. The set doesn't operate if it is not executed. 8.1.1 Main Monitor Station Preparation 1. Serial JIG cable: PQZZ1CD300E 2. PC in which "Tera Term (Ver. 4.78 later)" (communication software) is installed 3.

  • Page 21: Troubleshooting Guide

    9 Troubleshooting Guide 9.1 Operation Check of the Door Station START Advance preparation: Connect the Door Station to nondefective Main Monitor Station. Call from the Door Station. Does the ringtone Is the image displayed? sound from the Main Monitor Station? Is it possible to respond from Is it possible to respond from the main monitor station? the main monitor station?
  • Page 22 START Does the LED on the button of the Is the wiring correct Door Station light in standby mode? between the Main Monitor Station and (Is the voltage between terminals of the Door Station? the Door Station about 4~5V?) Rewire the Main Monitor Station and the Door Station correctly.
  • Page 23 No image can be seen by the call from the Door Station. (The ringer tone and the talking are OK.) Is the FM signal at pin3 of IC200 on the Main Board of the Door Station OK? (Refer to Fig.1) Check Signal Flow of the Image Signal (Door Station) Main Board Measuring conditions (FM signal):...
  • Page 24 If the front side of When lighing operation is door station is made dark, carried out with the Monitor Station, does lighting turn on does lighting turn on? automatically? Are there any missing /faulty parts around LED200 and LED201? Replace the Main board. Replace the fault parts.

  • Page 25: Operation Check Of The Main Monitor Station

    9.2 Operation Check of the Main Monitor Station START Advance preparation: Connect the Main Monitor Station to non-defective Door Station and Extension Monitor. *Make sure the power is ON by pressing the talk key, etc. Is the unit powered ON? Go to "Defect of the Main Monitor Station power supply "(*1). Register a normal Extension Monitor with the Main Monitor Station.

  • Page 26: Defect Of Communication Between The Main Monitor Station And Extension Monitor

    9.2.1 Defect of Communication Between the Main Monitor Station and Extension Monitor START Advance preparation: Connect a non-defective Door Station and the Extension Monitor to the Main Monitor Station. Communicate between tthe Extension Monitor and the Door Station. Can the video/voice communication be made? Are all parts on Talk Signal Path (Transmitting)

  • Page 27: Defect Of The Extension Monitor Video Recording

    9.2.2 Defect of the Extension Monitor Video Recording START Advance preparation: Connect a non-defective Door Station and the Extension Monitor to the Main Monitor Station. Communicate between the Door Station and the the Extension Monitor. Is it possible to record / play an image of the door station? Are all parts on Recording Image Operation...

  • Page 28: Defect Of The Main Monitor Station Power Supply

    9.2.3 Defect of the Main Monitor Station Power Supply 9.2.3.1 Defect of the Power board unit START Are the AC cord and Is the voltage of Rewire the AC cord correctly. the terminals connected to CL6 about 22V? CN1 properly. Is the voltage between both ends of VS1 Is the fuse(F1) is burned out? ranging from 220V...
  • Page 29 9.2.3.2 Defect of the Main board unit Detect of the Main unit power supply Check around Q31, Is the voltage of Replace the D31,R32,R31 and Is the unit powered C903 about 22V? fault parts. C34 of Main Board. ON ? Is the voltage of C904 Replace fuse(F900) on Main Board of Is the unit powered (Main Board) about...
  • Page 30 (from previous page) Check around IC930, L930,R931,R932,R933, Is the voltage of Replace the Is the unit powered C930,C932,C933,C934, CL930(Main Board) about fault parts. ON ? C935 and C937 4V?(12V→4V) of Main Board. Check around IC920, Is the voltage of L920,R921,R922,R923, Replace the Is the unit powered CL920(Main Board) about...
  • Page 31 (from previous page) Is the voltage of Check around Q230, Replace the Is the unit powered CL230(Main Board) about R230,R231, fault parts. ON ? 3.3V for LCD? of Main Board. Check around L230, Is the voltage of IC230,R256,C238,D232, Replace the Is the unit powered CL231(Main Board) about R237,R238,C241,C243...

  • Page 32: Defect Of The Main Monitor Station Video Recording

    9.2.4 Defect of the Main Monitor Station Video Recording START Advance preparation: Connect a non-defective Door Station to the Main Monitor Station. Communicate between the Door Station and the Main Monitor Station. Is it possible to record / play an image of the door station? Are all parts on Image Signal Path of...

  • Page 33: Defect Of The Communication Between The Main Monitor Station And The Door Station

    9.2.5 Defect of the Communication Between the Main Monitor Station and the Door Station START Advance preparation: Connect a non-defective Door Station to the Main Monitor Station. Communicate between the Main Monitor Station and the Door Station. Can the video/voice communication be made? Are all parts on Talk Signal Path (Transmitting) Replace the fault parts.

  • Page 34: Defect Of The Communication Between The Extention Monitor Station And The Door Station

    9.2.6 Defect of the Communication Between the Extention Monitor Station and the Door Station START Advance preparation: Connect a non-defective Door Station and Extension Monitor Station to the Main Monitor Station. Communicate between the Extension Monitor Station and the Door Station. Can the video/voice communication be made? Are all parts on...

  • Page 35: Defect Of The Key Board Unit

    9.2.7 Defect of the Key board unit START Confirm that the CL 910 of the main board becomes 5 V. Is the voltage of Is the cable connected to Connect the cables correctly. CL1001 about 5V? CN 701 and CN 1001? Is the voltage of Check around IC1001, Replace the...

  • Page 36: Signal Route

    9.3 Signal Route This chapter provides the testing procedures required for the P.C.B. parts. A signal route to be tested is determined depending upon purposes. The signal mainly flowing on this route is analog. You can trace the signal with an oscilloscope. The signal flow on each route is shown in the Check Sheet here.
  • Page 37 - 37 -...
  • Page 38 - 38 -...
  • Page 39 - 39 -...
  • Page 40 - 40 -...
  • Page 41 - 41 -...

  • Page 42: Disassembly And Assembly Instructions

    10 Disassembly and Assembly Instructions 10.1 Main Monitor Station 10.1.1 How to Remove the AC Cord [No.1] Remove 2 screws (a). Remove the Power cord cover. Keep pressing the terminal by Screwdriver's head and pull out the wires of the Power code as shown in Fig. 1. 10.1.2 How to Remove the Cabinet Cover [No.2] ■...

  • Page 43: How To Remove The Main Board, Speaker And Lcd [No.3]

    10.1.3 How to Remove the Main Board, Speaker and LCD [No.3] ■ Procedure No.1→No.2→No.3 Remove connector (Fig.2). Remove the solder of wires (Fig.3, Fig.4). Remove 2 screws (c). Remove the Main board with LCD holder from Cabinet body. Unhook the 4 tabs of the LCD holder. Remove the Flat cable from Main board as shown in Fig.5.

  • Page 44: How To Remove The Power Board, Key Board [No.4]

    10.1.4 How to Remove the Power board, Key board [No.4] ■ Procedure No.1→No.2→No.3→No.4 Remove 3 screws (d). Remove Power board from Cabinet body. Remove PCB holder from Cabinet body. Remove Key board from Cabinet body. - 44 -...

  • Page 45: Door Station

    10.2 Door Station 10.2.1 How to Remove the Front Panal [No.1] Unlock the hook by inserting the screw driver (Fig.A). Remove Front panel from Cabinet body. - 45 -...

  • Page 46: How To Remove The Door Station [No.2]

    10.2.2 How to Remove the Door Station [No.2] ■ Procedure No.1→No.2 Remove 4 screws (a). Case of Mounting base used Case of Flush mount box used - 46 -...

  • Page 47: How To Remove The Main Board And Camera Unit [No.3]

    10.2.3 How to Remove the Main Board and Camera Unit [No.3] ■ Procedure No.1→No.2→No.3 Remove 4 screws (b). Please remove the cabinet cover from cabinet body with care to the hooks. Remove the solder on the 3 pairs of lead wires (Fig.B, Fig.C, Fig.D). Disconnect the connector-A from the Camera Unit.

  • Page 48: How To Remove The Mic Board And Speaker [No.4]

    10.2.4 How to Remove the Mic Board and Speaker [No.4] ■ Procedure No.1→No.2→No.3→No.4 Remove the Mic board. Remove the Speaker. - 48 -...
  • Page 49 10.2.4.1 Note for Microphone Assembly (for anti-feedback) - 49 -...

  • Page 50: Installation Of The Lead Wires

    10.2.5 Installation of the lead wires When assembling the door station, route the lead wires as shown in the figure below, and be careful that they do not get caught. 10.2.6 Item to be checked after completion of assembly (camera lens angle adjustment) After completing assembly work, move the angle adjustment lever on the rear surface in the left and right directions, and confirm that it moves all the way.

  • Page 51: Measurements And Adjustments

    11 Measurements and Adjustments 11.1 Main Monitor Station 11.1.1 Main Board 11.1.1.1 Connections When replacing the main board (Monitor Station), please refer to the following items for adjusting. - 51 -...
  • Page 52 11.1.1.2 When replacing BBIC and X'tal ■ Preparation: 1. PC setting refer to [8.1.1 Main Monitor Station]. 2. Supply AC 230V. Note: Test points: Refer to [14.1.2 Main Board (Bottom View)]. Items Check Point Procedure 1.8 V Supply Adjustment CL437(BB1.8V) Confirm that the voltage between test point CL437 and CL109 (GND) is 1.8 V ± 0.02 V.

  • Page 53: Factory Mode

    11.1.2 Factory Mode ■ Entering Factory Mode: Turn AC Power “ON”, while pressing [F5] button, [TALK], about 5 seconds or more. Press [TALK] , [OFF],[F4] key sequentially. (FACTORY MODE screen is displayed.) ■ In order to exit Factory Mode: 1. Press the [F1] button. - 53 -...
  • Page 54 11.1.2.1 Factory Setup Initialize the logs and the all parameters except for the factory adjusted value, and delete the recorded images. 1. Select “FACTORY SETUP” by [F2] or [F3]. 2. Press [F4 (DECIDE)]. 3. Press [F4 (RUN)]. 4. Press [F1 (RESET)]. - 54 -...
  • Page 55 11.1.2.2 White Balance Adjustment The adjustment is done only when the color of the LCD display has changed after you have replaced the LCD. (Basically, adjustment is unnecessary.) 1. Select “TECHNICAL MODE 1” by [F2] or [F3]. 2. Select “WHITE BALANCE” by [F2] or [F3]. 3.

  • Page 56: Door Station

    4. Adjust the white balance by R Gain and B Gain. (1) Select the color to be adjust as below [F1] (>>): (Select Digit) • [F2] (▼), F3 (▲): (Change Value) • (2) Press [F4 (DECIDE)] (3) Adjust the white balance as below •...

  • Page 57: Miscellaneous

    12 Miscellaneous 12.1 How to Replace the Flat Package IC Even if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount), a soldering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins. 12.1.1 Preparation •...

  • Page 58: Flat Package Ic Installation Procedure

    12.1.3 Flat Package IC Installation Procedure 1. Temporarily fix the FLAT PACKAGE IC, soldering the two marked pins. *Check the accuracy of the IC setting with the corresponding soldering foil. 2. Apply flux to all pins of the FLAT PACKAGE IC. 3.

  • Page 59: Schematic Diagram

    13 Schematic Diagram Note: 1. DC voltage measurements are taken with an oscilloscope or a tester with a ground. 2. The schematic diagrams and circuit board may be modified at any time with the development of new technology. - 59 -...

  • Page 60: Main Monitor Station

    13.1 Main Monitor Station 13.1.1 Main Board (1) / External I/F D627 R627 6.2V C627 0.1u 16 R621 330 R611 330 0.01u 0.01u C612 C613 R615 R613 C621 C611 R616 R614 2.2k 2.2k D640 C630 R630 R625 R623 D611 D621 R626 R624 2.2k 2.2k R633...

  • Page 61: Main Board (2) / Bbic

    13.1.2 Main Board (2) / BBIC DPJP3 CL573 CL572 CL574 D560 CL571 R584 D561 CF571 R588 C562 C563 100k 100k R565 R564 CF572 C565 C564 R400 3300p 3300p 4.7k R572 R573 R571 R574 R589 R583 100k C585 C575 6.3V 22uF 100k R590 C401 C589...

  • Page 62: Main Board (3) / Dpjp3_Key

    13.1.3 Main Board (3) / DPJP3_KEY C100 2200p D100 4.71V C102 4.7k 0.1u 16 R102 IC101 1 GND R107 C101 2 VDD 220p C111 C106 1000p 0.01u 25 C103 R110 C105 C107 C104 C340 NC C112 C113 1uF 16V 0.1u 1000p 0.01u C114 1uF C115 1uF...

  • Page 63: Main Board (4) / Lcd

    13.1.4 Main Board (4) / LCD C230 1uF 6.3V R230 R231 C231 Q230 10uF Gth=1.8V C232 0.1uF C233 D230 C234 0.1uF R235 2.2k C237 0.1uF C238 COMP 3300pF FCLK IC230 R238 21.5k C241 10uF D234 R241 8.2k C247 10uF C248 10uF R246 C201 47pF...

  • Page 64: Main Board (5) / External I/F_Electric Lock

    13.1.5 Main Board (5) / External I/F_Electric lock CL621 CL622 CL601 CL623 CL602 CL624 CL603 CL613 CL604 CL614 CL605 CL615 CL606 CL616 CL607 CL617 CL608 CL618 CL609 CL610 CL611 CL612 R880 R881 150 C881 150 C880 0.1u 0.1u D281 R281 RL880 RL881 D881 D880...

  • Page 65: Main Board (6) / Dcdc

    13.1.6 Main Board (6) / DCDC 220uF 220uF 150uF 470 1W 47u 35 C901 C900 10uF C903 0.1u C904 0.1u 50 C905 10uF C907 C902 0.01u 25 C906 10uF C921 C911 C930 C920 C910 10uF 10uF 10uF R931 R911 R921 R932 60.4k R922 R912...

  • Page 66: Main Board (7) / Am Communication_Base Unit

    13.1.7 Main Board (7) / AM communication_base unit L719 L718 L720 L717 L713 L711 L721 L728 C721 C724 L722 L729 C722 C725 L723 L730 C723 C729 C710 0.1u 16 C715 C707 C748 1000p 1000p 1000p R724 R709 R779 R713 R789 R728 100k 100k 100k...

  • Page 67: Main Board (8) / Am Communication_Add Base Unit

    13.1.8 Main Board (8) / AM communication_add base unit D759 C759 NC C765 100p C766 100p R768 R762 NC R763 IC760 R770 AOUT 8.2k A-IN BOUT A+IN B-IN C777 C776 100p B+IN C772 NC C778 1000p C773 10uF C774 C487 1000p R771 R493 R497...

  • Page 68: Main Board (9) / Key

    13.1.9 Main Board (9) / KEY RX-VOL MENU TALK MONITOR PAD1 PAD2 PAD3 PAD4 PAD5 PAD6 PAD7 T3V3 CL1007 CL1001 T3V3 CL1003 CL1002 CN1001 T3V3 IC1002 CL1004 CL1005 RESET C1011 1000pF CAP0 C1008 0.1uF VANA C1009 0.1uF *RESETB R1011 GND3 *INTB GND4 C1010 0.1uF...

  • Page 69: Power Board

    13.1.10 Power Board 27uF 450V 15uF 450V 2000V C3 1000p 1000pF 0.22uF 25V CRG05(TE85L,Q) R7 10 R6 82k 33pF 2000V C5 1000pF 1000V 2000V C13 1000pF 0.125 0.125 2.2k C14 470u 25 C17 330uF 35V R26 1W 4.7k R27 1W 4.7k R15 10k 1% R17 39k 1% R16 220k 1%...

  • Page 70: Door Station

    13.2 Door Station 13.2.1 Main Board R231 0.1uF 0.1uF R232 C218 0.1uF C230 R201 4.7k C200 0.1uF R219 R226 C205 120k 1.8k 470pF C220 R225 0.1uF C212 C216 1000pF C221 R215 R214 R234 2.2k R220 R233 R221 6.3V 330uF 1.1k 2.2k LED201 R213 R212 LED200...

  • Page 71: Mic Board

    13.2.2 MIC Board L700 MIC+ MIC1 L701 MIC- VL-V524: Mic Board - 71 -...

  • Page 72: Printed Circuit Board

    14 Printed Circuit Board 14.1 Main Monitor Station 14.1.1 Main Board (Component View) IC300 IC100 C678 VL-MV74: Main Board (COMPONENT VIEW) - 72 -...

  • Page 73: Main Board (Bottom View)

    14.1.2 Main Board (Bottom View) D561 D560 C561 C563 C562 C102 C564 R564 R565 C565 D100 L174 L173 L172 L171 R281 D881 D880 C702 C790 R723 R722 IC701 R726 R727 C797 C661 C712 R796 R795 C657 R654 C652 R650 R651 C658 C340 C656 C654...

  • Page 74: Key Board

    14.1.3 Key Board (Component View) (Bottom View) R1004 R1003 IC1002 C1008 C1009 C1005 R1002 C1010 R1001 C1007 C1003 C1001 C1002 VL-MV74: Key Board - 74 -...

  • Page 75: Power Board

    14.1.4 Power Board (Component View) (Bottom View) VL-MV74: Power Board - 75 -...

  • Page 76: Door Station Board

    14.2 Door Station Board 14.2.1 Main Board (Component View) R231 L2L3 R232 IC102 C111 R126 C110 LED200 LED201 C218 R233 IC204 R234 R219 C220 L200 IC200 Q203 C217 C201 R206 R202 SW301 R205 Q301 R224 R304 R216 R303 C209 C206 LED1 R200 C202 C203 C204...

  • Page 77: Mic Board

    14.2.2 MIC Board (Component View) (Bottom View) P N L B 2 8 0 5 * * - Y Y - b M I C 1 C 7 0 0 VL-V524L: Mic Board - 77 -...

  • Page 78: Exploded View And Replacement Parts List

    15 Exploded View and Replacement Parts List 15.1 Exploded View 15.1.1 Main Monitor Station PCB1 PCB3 PCB2 - 78 -...

  • Page 79: Door Station

    15.1.2 Door Station PCB101 PCB102 E101 - 79 -...

  • Page 80: Accessories And Packing Materials Location

    P109 P108 A111 A112 P110 P102 P103 Note: (*1) "A101" and "A102" are VL-SV74BX, VL-SV74CX, VL-SV74AZ, VL-SV74ML, VL-SV74SX only. "A103" and "A104" are VL-SV74BX, VL-SV74CX only. "A105" is VL-SV74BX only. "A106" and "A107" are VL-SV74VN, VL-SV74VNP only. - 80 -...
  • Page 81 15.1.3.2 VL-MV74BX,VL-MV74CX,VL-MV74AZ,VL-MV74ML,VL-MV74SX,VL-MV74VN,VL-MV74VNP (*1) A201 A207 P201 P203 P202 A209 A208 P204 P205 P206 Note: (*1) "A201" and "A202" are VL-MV74BX, VL-MV74CX, VL-MV74AZ, VL-MV74ML, VL-MV74SX only. "A203" and "A204" are VL-MV74BX, VL-MV74CX only. "A205" is VL-MV74BX only. "A206" and "A207" are VL-MV74VN, VL-MV74VNP only. - 81 -...
  • Page 82 15.1.3.3 VL-V524LCE, VL-V524LSX, VL-V524LVN (Optional Unit) (*1) A301, A302, A303 P304 P305 A305 P306 P301 A304 A306 P305 P302 P303 Note: (*1) "A301" is VL-V524LCE, VL-V524LSX only. "A302" is VL-V524LCE only. "A303" is VL-V524LVN only. - 82 -...
  • Page 83 15.1.3.4 VL-MB524BX, VL-MB524SX, VL-MB524VN (Optional Unit) P403 P402 P401 - 83 -...

  • Page 84: Replacement Parts List

    15.2 Replacement Parts List Note: Safety Ref. No. Part No. Part Name & Description Remarks L0AA02A00129 SPEAKER 1. RTL (Retention Time Limited) PNHS1913Z SHEET for SPEAKER The “RTL” marking indicates that its Retention Time is PNHR2565Z PCB HOLDER Limited. PNMH1512Z LCD SHIELD When production is discontinued, this item will L5EDDYY00882 LCD (*1)
  • Page 85 Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks IC702 C0BBBA000024 Q881 B1GBCFYY0014 TRANSISTOR(SI) IC703 C0BBBA000024 IC704 C0JBAA000362 (DIODES) IC705 C0JBAA000362 DA2S10100L DIODE(SI) IC760 C0ABBB000179 D100 B0BC4R7A0268 DIODE(SI) IC800 B3PBA0000138 PHOTO ELECTRIC D101...
  • Page 86 Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks L205 J0JCC0000275 IC FILTER L764 G1C100MA0274 COIL L206 J0JCC0000275 IC FILTER L765 G1C100MA0274 COIL L207 J0JCC0000275 IC FILTER L766 G1C331JA0036 COIL L208 J0JCC0000275...
  • Page 87 Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks R112 ERJ3GEY0R00 R417 ERJ3EKF6801 6.8k R113 ERJ3EKF1002 R418 ERJ2GEJ103 R114 EXB24V102JX COMPONENTS PARTS, 1k R419 ERJ2GEJ103 R115 ERJ2GE0R00 R420 ERJ2GEJ103 R116 ERJ2GE0R00 R421...
  • Page 88 Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks R623 ERJ2GEJ103 R725 ERJ3GEYJ152 1.5k R624 ERJ2GEJ222 2.2k R726 ERJ3GEYJ152 1.5k R625 ERJ2GEJ103 R727 ERJ3GEYJ100 R626 ERJ2GEJ222 2.2k R728 ERJ3GEYJ104 100k R627 PQ4R10XJ471...
  • Page 89 Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks R816 ERJ2GEJ184 180k C132 ECUE1C104KBQ R817 ERJ2GEJ184 180k C133 ECUE1C104KBQ R818 ERJ2GEJ123 C134 ECUE1C104KBQ R819 ERJ2GEJ473 C135 ECUE1C104KBQ R820 PQ4R18XJ562 5.6k C136 ECUE1C104KBQ...
  • Page 90 Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks C239 F1H1H104A913 C489 ECUV1H104KBV C240 F1H1H104A913 C500 F1K1E1060009 C241 F1K1E1060009 C501 F1L1E1060021 C242 F1H1H104A913 C502 ECUE1E103KBQ 0.01 C243 ECUE1H102KBQ 0.001 C503 ECUE1H102KBQ 0.001...
  • Page 91 Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks C653 F1G1H821A541 820p C771 ECUE1H100DCQ 10p C654 ECUE1H100DCQ 10p C773 F1K1E1060009 C657 F1K0J476A004 C775 ECUE1H101JCQ 100p C658 ECUE1H100DCQ 10p C776 ECUE1H100DCQ 10p C659 ECUE1H102KBQ...
  • Page 92 Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks C934 F1L1C2260012 (ICs & PHOTO ELECTRIC TRANSDUCER) C935 F1G1H821A541 820p MIP2M40MTSCF C937 ECUV1H104KBV B3PBA0000485 PHOTO ELECTRIC C950 ECUV1C105KBV TRANSDUCER C951 ECUV1C105KBV C0DBAYY00781 C952...

  • Page 93: Door Station

    Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks F1H1E224A098 0.22 IC203 It is impossible to supply (IC203) by itself. Therefore, when this part is in need of replacing, F1K1H106A208 please replace the Main Board(PCB101).
  • Page 94 Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks (RESISTORS) R225 ERJ2GEJ102 ERJ2GEJ510 R226 ERJ2GEJ182 1.8k ERJ2GEJ120 R227 ERJ2GEJ101 ERJ3GEYJ561 R228 ERJ2GEJ101 PQ4R10XJ100 R232 ERJ2GEJ750 PQ4R10XJ100 R233 ERJ2GEJ112X 1.1k ERJ3GEYJ561 R234 ERJ2GEJ222...

  • Page 95: Accessories And Packing Materials

    (*4) You can download and refer to the “Installation Guide” P105 XZB18X27A04 PROTECTION COVER for etc. on TSN Server. DOOR STATION P106 XZB05X08A04 PROTECTION COVER for SCREW 15.2.3.1 VL-SV74BX P107 XZB10X15A04 PROTECTION COVER for SCREW Safety Ref. No. Part No. Part Name & Description Remarks P108...
  • Page 96 15.2.3.3 VL-SV74AZ 15.2.3.5 VL-SV74SX Safety Ref. No. Part No. Part Name & Description Remarks Safety Ref. No. Part No. Part Name & Description Remarks A101 PNQW5671Z IMPORTANT INFORMATION A101 PNQW5671Z IMPORTANT INFORMATION AND QUICK GUIDE (for AND QUICK GUIDE (for English)(*4) English)(*4) A102 PNQX8844Z INSTALLATION GUIDE (for...
  • Page 97 Safety Ref. No. Part No. Part Name & Description Remarks 15.2.3.7 VL-MV74BX (Optional Unit) Safety Ref. No. Part No. Part Name & Description Remarks P201 XZB20X35A04 PROTECTION COVER for PRINTED MATERIALS A201 PNQW5671Z IMPORTANT INFORMATION P202 XZB11X30A02 PROTECTION COVER for AND QUICK GUIDE (for POWER CORD English)(*4) P203...

  • Page 98: Fixtures And Tools

    Safety Ref. No. Part No. Part Name & Description Remarks 15.2.3.12 VL-MV74VN/VL-MV74VNP (Optional Unit) Safety Ref. No. Part No. Part Name & Description Remarks A201 PNQW5676Z IMPORTANT INFORMATION 15.2.3.15 VL-V524LVN (Optional Unit) AND QUICK GUIDE (for Vietnamese)(*4) Safety Ref. No. Part No. Part Name &...

This manual is also suitable for:

Vl-sv74cxVl-sv74azVl-sv74mlVl-sv74sxVl-sv74vnVl-sv74vnp ... Show all

Table of Contents