1 Safety Precautions 1.1 Information for Your Safety file:///C|/Users/n.shetabi/AppData/Local/Temp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_01.xml[11/12/2018 3:48:21 PM]...
1.2 Cautions for use file:///C|/Users/n.shetabi/AppData/Local/Temp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_01.xml[11/12/2018 3:48:21 PM]...
2. Once "LENS MAIN UNIT" (Ref. 220) is confrmed as defective, place order "LENS Unit" (Ref. 200) and replace REAR FRAME UNIT (Ref. 205), to maintain Serial number of owner's original lens. Fig. 1-1 3. No adjustment is required when replacing the part mentioned on Fig.1-1. But, when tighten the concerned screws,apply proper torque file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_02.xml[11/12/2018 3:49:12 PM]...
4 Location of Controls and Components file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_04.xml[11/12/2018 3:49:51 PM]...
The repair quality is considered, and it is recommended working in the environment of satisfed clean level less than class 10,000 (Federal Standard 209D). [NOTE] Work in the environment of satisfed clean level less than class 10,000 (Federal Standard 209D) for cleaning the inside of the lens. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_05.xml[11/12/2018 3:50:12 PM]...
Keep covering the lens unit with Lens caps (front & rear), other than necessary cases. 6.2 Disassembly Flow Chart 6.3 Disassembly Procedure Important: It must be performed inside of satisfed clean level. (Satisfed clean level: Less than class 10,000(Federal Standard 209D)) file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
Page 13
3. Insert the small fat blade screwdriver to Gap (between the Decoration Ring and lens glass), and peel off the Decoration Ring gently. 6.3.3 Removal of the Lens Top Unit and the Dustproof Rubber 1. Remove 3 screws (A) and the Lens Top Unit. 2. Remove the Dustproof Rubber. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
Page 14
6.3.5 Removal of the L Mount Unit and the Lens Mount Rubber 1. Remove screw (C) and 4 screws (D). 2. Insert 4 Adjustment Shafts (VMS7941 or an equivalent one) to screw holes in order not remove Adjustment washes. 3. Remove the L Mount Unit. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
Page 15
6.3.7 Removal of the Rear Frame Unit and the OIS Switch 1. Disconnect the Connector of the Main P.C.B.. 2. Remove 4 screws (E) and the Rear Frame Unit. 3. Remove the bond by fat brade screwdriver in the following state. 4. Remove the OIS Switch. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
6.3.8 Removal of the Main P.C.B. and the Mount Contact Unit 1. Disconnect 4 connectors of the Main P.C.B.. 2. Remove the Main P.C.B. and the Moount Contact Unit. 3. Remove the Mount Connect Unit from Main P.C.B.. 6.4 Assembly Flow Chart 6.5 Assembly procedure file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
Page 17
6.5.2 Installation of the OIS Switch and the Rear Frame Unit 1. Install the OIS Switch in the following state. 2. Apply "CEMEDINE SUPER X 8008 BLACK" (Commercial Item) to the following 2 points after installing the OIS Switch. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
Page 18
3. Connect FPC to connector of the Main P.C.B.. 4. Tighten 2 screws (G) in numerical order by using the torque driver with specifed torque. 6.5.3 Installation of the Lens Mount Spacer 1. Put the Lens Mount Spacer on the Rear Frame Unit slowly. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
Page 19
1. Install the Lens Mount Rubber. 2. Install the L Mount Unit. 3. Remove the 4 Adjustment Shafts (VMS7941 or an equivalent one). 4. Tighten 4 screws (D) and screw (C) in numerical order by using the torque driver with specifed torque. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
Page 20
1. Install the Shading Frame. 2. Tighten 3 screws (B) in numerical order by using the torque driver with specifed torque. 6.5.6 Installation of the Dustproof Rubber and the Lens Top Unit 1. Install the Dustproof Rubber. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
Page 21
Use new one, do not use the one which is removed. Double-stick tape sticks to the Decoration Ring of the repair part. Remove the old double-stick tape from the Lens Top Unit. 2. After installing the Decoration Ring, use a soft cloth to press it into place. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
Page 22
6.5.8 Installation of the Zoom Rubber Ring 1. Install the Zoom Rubber Ring. file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_06.xml[11/12/2018 3:50:43 PM]...
1. Blow off the dust on the Lens glass surface with the Blower, gently. (Do not blow strongly.) 2. Wipe out the dirt on the Lens glass surface with Lens Cleaning Kit (VFK1900BK) if necessary. (Consult the instruction sheet which is included in the Lens Cleaning Kit in details.) file:///C|/U...emp/Rar$EXa0.519/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/doc/DSC1703009CE_07.xml[11/12/2018 3:51:05 PM]...
Page 24
Print Parts List Model No. : H-HSA35100PP/E/GK parts list note Model No. : H-HSA35100PP/E/GK Frame and Casing Section file:///C|/U.../Temp/Rar$EXa0.258/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/mec2/en/html/print_all.htm[11/13/2018 9:13:03 AM]...
Page 25
Print Parts List Model No. : H-HSA35100PP/E/GK Packing Parts and Accessories file:///C|/U.../Temp/Rar$EXa0.258/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/mec2/en/html/print_all.htm[11/13/2018 9:13:03 AM]...
Page 26
Print Parts List Model No. : H-HSA35100PP/E/GK Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks DVZE1008Z LENS CAP VFC4605 LENS REAR CAP VPF1475 LENS BAG VYC1085 LENS HOOD UNIT OPERATING INSTRUCTIONS (ENGLISH/CA file:///C|/U.../Temp/Rar$EXa0.258/viewing/SGML_VIEW_DATA/ALL/H-HSA35100PP/SVC/DSC1703009CE/mec2/en/html/print_all.htm[11/13/2018 9:13:03 AM]...