Sealey SA31.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
‰
Familiarise yourself with the applications, limitations and potential hazards peculiar to the riveter.
9
WARNING! Disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.
‰
Maintain the riveter in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the work area clean, uncluttered and ensure that there is adequate lighting.
9
Keep the riveter clean for best and safest performance.
9
WARNING! Always wear approved eye or face protection when operating the riveter.
‰
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain, and/or tie back, long hair.
9
Keep the riveter away from your body and at a safe distance from others.
9
Keep children and unauthorised persons away from the work area.
9
Secure unstable workpiece with a clamp, vice or other adequate holding device.
9
Ensure that spent rivet stems are disposed of correctly and do not cause a hazard.
9
WARNING! Ensure that the correct air pressure is maintained and not exceeded.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
DO NOT use the riveter for any purpose other than that for which it is designed.
8
DO NOT use the riveter if the safety cap is not in place.
8
DO NOT operate the riveter if any parts are damaged or missing and ensure that the safety cap is correctly fitted.
8
DO NOT carry the riveter by the hose, or yank the hose from the air supply.
8
DO NOT get the riveter wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT allow untrained persons to operate the riveter.
8
DO NOT point or fire the riveter at people or animals.
8
DO NOT operate the riveter when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from the air supply and store in a safe, dry, childproof area.
9
Always connect a leader hose to the rivetter with a permanent coupling.
9
2. INTRODUCTION
Powerful tool suitable for both aluminium and blind steel rivets up to 3/16". Supplied with four riveting nozzles and two spanners. Trigger
operated riveter with hardened steel jaw assembly and rivet shaft safety cap.
3. SPECIFICATION
Model No:................................................................SA31.V3
Air Consumption: ........................................................... 4cfm
Blind Rivet Type: ................Aluminium, Steel, Stainless Steel
Noise Power/Pressure: ........................................ 80/72dB(A)
Nozzle sizes: ..........................................................................
.........3/32"(2.4mm), 1/8"(3.2mm), 5/32"(4mm), 3/16"(4.8mm)
Operating Pressure: ...................................................... 90psi
Vibration/Uncertainty: ....................................... 20.96/1.5m/s²
4. AIR SUPPLY
WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the riveter. Too high an air pressure and unclean
‰
air will cause excessive wear, and may be dangerous, causing damage and/or personal injury.
4.1. Ensure the riveter air valve (or trigger) is not depressed before connecting to the air supply.
4.2.
You will require an air pressure between 70-90psi, and an air flow according to the specification above.
4.3. Drain the compressor daily. Water in the air line will damage the riveter and invalidate your warranty.
© Jack Sealey Limited
AIR/HYDRAULIC RIVETER
MODEL NO:
Wear protective Wear ear
gloves protection
Original Language Version
SA31.V3
SA31.V3 Issue:2 (3) 02/08/21