Sealey SA312.V2 Manual

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAfety
WArninG! Ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the riveter.
9
WArninG! disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.
‰
Maintain the riveter in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
Keep the riveter clean for best and safest performance.
9
WArninG! Always wear approved eye (or face) and hand protection when operating the riveter.
‰
Maintain correct balance and footing. DO nOt over reach, ensure the floor is not slippery, wear non slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear or working parts.
9
Keep the riveter away from your body and at a safe distance from others.
9
Keep children and unauthorised persons away from the working area.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
ensure that spent rivet stems are disposed of correctly and DO nOt cause a hazard.
9
WArninG! ensure correct air pressure is maintained and not exceeded. Recommended pressure 90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are
9
secure.
DO nOt use the riveter for a task it is not designed to perform.
8
DO nOt operate the riveter if any parts are damaged or missing as this may cause failure and/or personal injury.
8
ensure the safety cap is correctly fitted.
9
DO nOt carry the riveter by the hose, or yank the hose from the air supply.
8
DO nOt get the riveter wet or use in damp or wet locations or areas where there is condensation.
8
DO nOt allow untrained persons to operate the riveter.
8
DO nOt operate the riveter when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO nOt direct air from the air hose at yourself or others.
8
When not in use disconnect from the air supply and store in a safe, dry, child proof location.
9
Avoid unintentional starting.
9
2. intrODuctiOn
Suitable for aluminium, steel and stainless steel rivets up to 3/16". Supplied with four riveting nozzles and two spanners. Trigger operated
riveter with hardened steel jaw assembly and rivet shaft safety cap. Will handle heavy assembly work.
3. SpecificAtiOn
Model no: .................................................................................................................. SA312.V2
Air Consumption: ............................................................................................................... 4cfm
Air Inlet Size: ................................................................................................................. 1/4"BSP
Blind Rivet Type: .................................................................... Aluminium, Steel, Stainless Steel
nett Weight: ......................................................................................................................1.3Kg
noise Power/Pressure: .................................................................................................81/71dB
nozzle Size(s): ..................................... 3/32"(2.4mm), 1/8"(3.2mm), 5/32"(4mm), 3/16"(4.8mm)
operating Pressure: ...........................................................................................................90psi
4. Air Supply
WArninG! ensure the air supply is clean and does not exceed 90 psi while operating the riveter. Too high an air pressure and
‰
unclean air will cause excessive wear, and may be dangerous, causing damage and/or personal injury.
4.0.1. ensure the riveter air valve (or trigger) is not depressed before connecting to the air supply.
4.0.2. You will require an air pressure between 70-90psi, and an air flow according to the specification above.
4.0.3. drain the air tank daily. Water in the air line will damage the riveter and invalidate your warranty.
© Jack Sealey limited
Air riveter 3/16" Steel Aluminium &
StAinleSS Steel rivetS
Model no:
Wear protective Wear ear
gloves protection
Original Language Version
SA312.v2
SA312.V2 Issue 1 18/02/19