Page 1
2: .187 quick-connect terminal 0: AgNi alloy 6: Wire leads 1: AgNi alloy + Au-clad Note) Not every combination is available. Please refer to the following table, “PRODUCT TYPES” . 2021.10 industrial.panasonic.com/ac/e/ AECTB7E 202110 ー 1 ー Panasonic Corporation 2021...
Page 2
ABV163650 Notes: 1. For items with international safety certification, please put “3” in the tenth digit of the part number when ordering. 2. Push plunger color: black Panasonic Corporation Electromechanical Control Business Division AECTB7E 202110 ー 2 ー Panasonic Corporation 2021...
Page 3
ABV163651 Notes: 1. For items with international safety certification, please put “3” in the tenth digit of the part number when ordering. 2. Push plunger color: dark red Panasonic Corporation Electromechanical Control Business Division AECTB7E 202110 ー 3 ー Panasonic Corporation 2021...
30 V 15 V 250 V Note) The diagram above is intended as a reference. Please use the product within the rated voltage and current. Panasonic Corporation Electromechanical Control Business Division AECTB7E 202110 ー 4 ー Panasonic Corporation 2021 industrial.panasonic.com/ac/e/...
Page 5
17.2 General tolerance: ±0.4 Pretravel (PT) Max. 3.2 mm Movement Differential (MD) Max. 1.2 mm Overtravel (OT) Min. 1.2 mm Operating Position (OP) 15.3±1.2 mm Panasonic Corporation Electromechanical Control Business Division AECTB7E 202110 ー 5 ー Panasonic Corporation 2021 industrial.panasonic.com/ac/e/...
Page 6
34.2±0.5 General tolerance: ±0.4 Pretravel (PT) Max. 3.2 mm Movement Differential (MD) Max. 1.2 mm Overtravel (OT) Min. 1.2 mm Operating Position (OP) 20.7±1.2 mm Panasonic Corporation Electromechanical Control Business Division AECTB7E 202110 ー 6 ー Panasonic Corporation 2021 industrial.panasonic.com/ac/e/...
Page 7
* With UL and CSA approved products, lead wire is changed to UL compliant (AWG18). Please refer to "the latest product specifications" when designing your product. •Requests to customers: https://industrial.panasonic.com/ac/e/salespolicies/ Panasonic Corporation Electromechanical Control Business Division AECTB7E 202110 ー 7 ー Panasonic Corporation 2021 industrial.panasonic.com/ac/e/...
Page 8
Selection of the switch Allow for up to 20% variation of the specified characteristics values to compensate for long term operational wear of the switch in your design. Panasonic Corporation Electromechanical Control Business Division AECTB35E 202110 ー 8 ー Panasonic Corporation 2021...
Page 9
Do not clean the switch. Doing so can cause problems. Please contact us if cleaning is necessary. 1000 Standard value 30 minutes 8 10 12 14 16 18 20 22 24 Elapsed time (h) Panasonic Corporation Electromechanical Control Business Division AECTB35E 202110 ー 9 ー Panasonic Corporation 2021 industrial.panasonic.com/ac/e/...
Page 10
Underwater type Unit can be used underwater Note: Details of test conditions are the same as NECA C 0920. Please refer to them. Panasonic Corporation Electromechanical Control Business Division AECTB35E 202110 ー 10 ー Panasonic Corporation 2021 industrial.panasonic.com/ac/e/...
Malfunction shock ... Shock range where a closed contact does not open for longer than a specified time due to shocks during use of the snap-action switches. Panasonic Corporation Electromechanical Control Business Division AECTB36E 202110 ー 11 ー Panasonic Corporation 2021...
Page 12
Position degree position to its original position. Total travel The stopping position of the actuator after Position degree total travel. Panasonic Corporation Electromechanical Control Business Division AECTB36E 202110 ー 12 ー Panasonic Corporation 2021 industrial.panasonic.com/ac/e/...
Page 13
8) If snap-action switch operation is synchronized with the AC supply phase, this may cause: shortened electrical life, contact fusion failure, contact transfer, or other reliability problems. Panasonic Corporation Electromechanical Control Business Division AECTB36E 202110 ー 13 ー Panasonic Corporation 2021...
Page 14
Can be used for both AC and DC. Varistor Load 3) Avoid circuits which apply voltage between contacts. (This may lead to mixed deposition.) Wrong 200 V 100 V Panasonic Corporation Electromechanical Control Business Division AECTB36E 202110 ー 14 ー Panasonic Corporation 2021 industrial.panasonic.com/ac/e/...
Page 15
OP Min - 100% of OT = 8.0 - 1.2 = 6.80 mm The plunger/lever should be pressed down to the position of 6.80 to 7.16 mm from the mounting hole. Panasonic Corporation Electromechanical Control Business Division AECTB36E 202110 ー 15 ー...
In terms of the packing format used, make every effort to keep the effects of moisture, organic gases and sulfide gases to the absolute minimum. Panasonic Corporation Electromechanical Control Business Division AECTB36E 202110 ー 16 ー Panasonic Corporation 2021...
Page 17
Large Medium Small Possible lever The force required for pin plunger action is lighter than that of the lever, and the stroke is longer. Panasonic Corporation Electromechanical Control Business Division AECTB36E 202110 ー 17 ー Panasonic Corporation 2021 industrial.panasonic.com/ac/e/...