動作温度:0 ℃〜 40 ℃ (HDR-CX610E/PJ530E/PJ540E/ PJ610E)) compatible): Operating temperature: 0 °C to 40 °C MP4方式 保存温度:−20 ℃〜 +60 ℃ [切] のとき The unique pixel array of Sony’s ClearVid Video: MPEG-4 AVC/H.264 (32 °F to 104 °F) 映像:MPEG-4 AVC/H.264 *4 外形寸法 (約) : [ 手ブレ補正] が [アクティブ] のとき...
Page 3
Model information table Model CX530E CX535 CX610E PJ530E PJ540 PJ540E PJ610E Destination AEP, UK, NE US, CND, E, E, AUS, HK, JE KR, J COLOR system NTSC NTSC Internal recording – Internal memory Internal memory – Internal memory Internal memory Internal memory media 32 GB...
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO- CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM- サービス,点検時には次のことにご注意ください。 NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES...
1. SERVICE NOTE – ENGLISH – 1-1. POWER SUPPLY DURING REPAIRS About unit with Internal Memory Model (EXCEPT CX530E/PJ530E) After the board replacement, execute the procedure below first. 1. Execute the [DESTINATION DATA WRITE] of ADJUST tab in the Adjust Manual. In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 Vdc), the power is shut off 2.
– ENGLISH – 4. Confirm on the personal computer that the unit is detected as a connectable wireless network. 1-5. SELF-DIAGNOSIS FUNCTION 5. To further confirm that the unit is connectable, connect the unit to the personal computer and double-click the “current connection”from the icon displayed on the notice field, make sure that the unit is displayed in the Wireless internet access column.
– ENGLISH – Self-diagnosis Code Self-diagnosis Code Symptom/State Correction Symptom/State Correction Block Detailed Block Detailed Function Code Function Code The abnormalities in initialization of CX535/PJ530E/PJ540/PJ540E: the focus lens and the abnormalities in Inspect the flash memory (IC8101 on the MM-102 board). Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Page 8
– ENGLISH – 1-6-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred 1-7. NOTE ON REPLACING PROJECTOR UNIT (Projector Model) Order Procedure Refer to the following flowchart when repairing or inspecting the projector’s projection function. Turn the power OFF. While measuring with an oscilloscope the output voltage of R1401 in the periphery of IC6800 on the VC-1025 board, turn the power If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow- ON to check that the output voltage immediately after the power on change as shown in Fig.
Page 9
– ENGLISH – Projector problem checking procedure (indication on brightness) 1-8. FRONT ORNAMENT REPLACING METHOD Indicated defective projector received 1 Refer to the ADJUST tab of Adjust Manual. Note: A protective Lens Cap is attached to each new service 2 Refer to the SERVICE tab of Adjust Manual. Lens Block.
Page 10
– ENGLISH – (5) Remove the three screws and remove the Motor B. (7) Remove the six screws and remove the Frame (E-SUB-A), Frame (9) Remove the three screws and remove the Sheet Metal B and the (11) Remove the three screws and remove the Sheet Metal A while (E-SUB-B), Ball Bearing while detaching the six bosses and the Mecha Stop Rubber while detaching the two bosses.
– ENGLISH – (13) Remove the two screws and remove the Sheet Metal D while de- Installation (3) While installing the two bosses, stick the Adhesive Part of the (4) Connect the connector and install the Sheet Metal A and the FP- taching the two bosses.
Page 12
– ENGLISH – (5) Set the Plate of the Motor A in the state shown in the figure and (7) Stick the Adhesive Part of the Motor A Flexible Board while (9) Stick the Adhesive Part of the FP-2189 Flexible Board and the (10) Set the Plate of the Motor B to the state shown in the figure and install the Motor A matching it with the two bosses on the Sheet matching it with the two bosses.
Page 13
– ENGLISH – (12) Pass the FP-2189 Flexible Board through the F-SUB-B hole and (13) Install the Edge of Mechanical Rubber to the Sheet Metal C and (14) Stick the Adhesive Parts of the Motor A Flexible Board, Motor B stick the Adhesive Part.
2. REPAIR PARTS LIST IDENTIFYING PARTS (ENGLISH) The components identified by mark 0 or dotted line with mark 0 are critical for safety. NOTE: Follow the disassembly in the numerical order given. Replace only with part number specified. • -XX, -X mean standardized parts, so they may have some differences from the original 1 Cabinet (LR) Assy one.
– ENGLISH – – JAPANESE – OPERATION NOTES 作業時の注意 Make sure that the conductive side of a flexible board does not have any stain or foreign materials. フレキシブル基板の導電面に汚れやごみなどがないことを確認してください。 Do not touch the conductive side of flexible boards with bare hands. フレキシブル基板の導電面を素手で触れないようにしてください。...
Page 25
2-1. EXPLODED VIEWS DISASSEMBLY 2-1-1. OVERALL SECTION-1 1. Remove in numerical order ( ) in the left figure. #2 X 2 Open the LCD (1) → #12 X 1 Bottom View Right View Back View (Claws) #2 X 1 → #12 X 1 → #2 X 2 → #12 X 1 → #2 X 1 Bottom View (Claws) Right View...
Page 26
DISASSEMBLY 2-1-2. OVERALL SECTION-2 1. Remove in numerical order ( ) in the left figure. #12 X 1 #140 X 1 Left View Left View #140 Refer to "Caution for Handling the Lens Device (LSV-1610B)" Lens Section-1 #12 X 1 → #2 X 1 #2 X 1 →...
Screw 2-1-5. CABINET (R) SECTION #2: M1.7 X 4.0 #12: M1.7 X 5.0 (Tapping) #288: M1.7 X 2.5 (Projector Model) (Black) (Black) (Black) 2-635-562-31 3-080-204-21 2-187-345-21 Refer to page 2-10 about Non Projector Model. J901 Note SP901 Note 1: JK-1009基板のリチウム蓄電池 (BT4200) を交換する場合は Note 1: Replace the battery holder (BH4200) together when replac- ing the lithium storage battery (BT4200) on the JK-1009 バッテリホルダ ...
Screw 2-1-6. LCD SECTION #2: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #30: M1.2 X 3.5 (Tapping) (Projector Model) (Black) (Silver) (White) 2-635-562-31 3-078-890-11 3-086-156-11 Refer to page 2-11 about Non Projector Model. LCD Section-2 Note (See Page 2-9) Note : Note : PRECAUTIONS WHEN HOLDING THE PROJECTOR UNIT...
Page 31
Screw 2-1-7. LCD SECTION-2 #2: M1.7 X 4.0 #288: M1.7 X 2.5 (Projector Model) (Black) (Black) 2-635-562-31 2-187-345-21 Refer to page 2-11 about Non Projector Model. (Note 1) #288 Note (Note 2) Note 1: This screw cannot be reused. Discard the screw removed Note 1: このねじは再利用することができません。...
Page 32
Screw 2-1-8. CABINET (R) SECTION #2: M1.7 X 4.0 #12: M1.7 X 5.0 (Tapping) #288: M1.7 X 2.5 (Non Projector Model) (Black) (Black) (Black) 2-635-562-31 3-080-204-21 2-187-345-21 Refer to page 2-7 about Projector Model. J901 Note SP901 Note 1: JK-1009基板のリチウム蓄電池 (BT4200) を交換する場合は Note 1: Replace the battery holder (BH4200) together when replac- ing the lithium storage battery (BT4200) on the JK-1009 バッテリホルダ ...
Page 33
Screw 2-1-9. LCD SECTION #2: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #288: M1.7 X 2.5 (Non Projector Model) (Black) (Silver) (Black) 2-635-562-31 3-078-890-11 2-187-345-21 Refer to page 2-8 about Projector Model. #288 (Note 1) (Note 2) Note Note 1: このねじは再利用することができません。 Note 1: This screw cannot be reused.
Page 34
• EXCEPT J MODEL ACCESSORIES This Item is not supplied with the unit as an accessory, but it is prepared as a service part. When the customer requests printed one, ask Head Quarter. Ref. No. Part No. Description Ref. No. Part No.
Page 36
3. ASSEMBLY Assembly-1: Notes on Assembling the Lens Ornamental Assembly-2: The Method of attachment of FP-2192/2193 Flex- CAUTION FOR HANDLING THE ible Board LENS DEVICE (LSV-1610B) 1 Fold dotted line parts of the FP-2192/2193 flexible 2 Roll the FP-2192/2193 Flexible Board 2 times Do not hold the following part.
Page 37
Assembly-3: How to distinguish the side of Optical Filter Block facing to Lens Device The one side of the Optical Filter Block has treated with IR cut coating. Mount the Optical Filter Block facing the IR cut coated side to the lens device.
Page 38
7. ADJUSTMENT (ENGLISH) For adjusting these models, the Adjust manual and the Adjust station are required. Adjust station It is the software to start up Adjust manual for each model. The installer of the Adjust station and the installation manual are attached, be sure to confirm the contents of them. Adjust manual It is the software to adjust and check digital cameras and camcorders for service.