Related Manuals for Huawei OptiXstar P612E
Summary of Contents for Huawei OptiXstar P612E
- Page 1 OptiXstar P612E Quick Start Issue Date 2019-12-31 HUAWEI TECHNOLOGIES CO., LTD.
- Page 2 Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
-
Page 3: Table Of Contents
OptiXstar P612E Quick Start Contents Contents 1 Product Appearance........................ 1 2 Installing the Device....................... 2 3 Connecting Cables.........................11 4 Description of Indicator....................... 13 5 Technical Specifications....................... 15 6 FAQs............................16 Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd. -
Page 4: Product Appearance
Figure 1-2 Device back and bottom ● If the appearance of the product in this document differs from the actual product, the actual product prevails. ● See the nameplate on the bottom of the device. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd. -
Page 5: Installing The Device
The OptiXstar P612E supports indoor desktop installation, wall mounting, or network box installation. NO TICE ● The OptiXstar P612E belongs to the remote optical access unit (ONU) product series. It is referred to ONU in the following description. ● Do not stack horizontally placed ONU. - Page 6 6 to 8 mm, and the length should not be less than 20 mm. Use a screwdriver to fasten the screws into the expansion bolts, reserving 5 mm ends out of the wall, and mount the ONU onto the screws. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd.
- Page 7 OptiXstar P612E Quick Start 2 Installing the Device Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd.
- Page 8 ● The method for installing the ONU in a non-Huawei network box depends on the network box specifications. When the ONU is installed in a non-Huawei network box, the preceding heat dissipation space rules must be observed.
- Page 9 – Decouple the surge protector from the ONU power source using a power cable of 3–5 m. ● Guide for Grounding the Network Box of the TT Power Distribution System Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd.
- Page 10 As specified by the grounding standard, the cross-sectional area of the external ground cable must be greater than or equal to 16 mm ● Guide to Ground the Strength Member Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd.
- Page 11 Install the network box and ONU based on the instructions provided in this document. Grounding solution 1: The fiber strength member is isolated from the network box and grounded outside the network box. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd.
- Page 12 Then, use insulation tape to wrap the stripped optical cable. When wrapping the waterproof tape, ensure that fiber cores are force-free. iii. Cut excess fiber strength member for grounding. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd.
- Page 13 Otherwise, heavy currents may be discharged using the network ports on the local and peer devices, which may damage these network ports. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd.
-
Page 14: Connecting Cables
● The ONU supports PoE total output power up to 60W, and each POE port supports up to 30W. ● The output voltage of POE ports is 56V DC. Power Connects to a power adapter. On/Off Powers the ONU on or off. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd. - Page 15 Press the button for a short time to reset the device, or press the button for a long time (longer than 10s) to restore the device to the default settings and reset the device. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd.
-
Page 16: Description Of Indicator
The status of PON and LOS reflects the connection between ONU and the optical line terminal (OLT). The following table describes the status of the PON and LOS LEDs. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd. - Page 17 Blinks once The ONT is not connected to fibers or does every 2 not receive optical signals. seconds Blinks once Blinks once The hardware is faulty. every 2 every 2 seconds seconds Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd.
-
Page 18: Technical Specifications
-5°C to +45°C Operating humidity 5%RH to 95%RH (non-condensing) Note: The fuse specifications in the device are 63V DC / 1.5A , 125 V DC / 1A and 125 V DC / 3A. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd. -
Page 19: Faqs
● If the LOS indicator blinks twice a second, the ONU is prohibited by the upper-layer device or blinks abnormally. Contact the service provider for help. Issue 02 (2019-12-31) Copyright © Huawei Technologies Co., Ltd. - Page 20 How do I restore the Huawei ONT to factory setting? Press Reset by using a needle-type object for longer than 10s to restore factory defaults and reset the Huawei ONT. If the indicator is off (except power indicator) and then is lit, the system restarts successfully.