Related Manuals for Huawei OptiXstar P802E
Summary of Contents for Huawei OptiXstar P802E
- Page 1 OptiXstar P802E Quick Start Issue Date 2019-09-30 HUAWEI TECHNOLOGIES CO., LTD.
- Page 2 Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
-
Page 3: Table Of Contents
OptiXstar P802E Quick Start Contents Contents 1 Product Appearance........................1 2 Installing the Device........................2 3 Connecting Cables........................10 4 Description of Indicator......................11 5 Technical Specifications......................13 6 FAQs...............................14 Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd. -
Page 4: Product Appearance
OptiXstar P802E Quick Start 1 Product Appearance Product Appearance If the appearance of the product in this document differs from the actual product, the actual product prevails. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd. -
Page 5: Installing The Device
The OptiXstar P802E supports outdoor network box installation and indoor desktop installation, wall mounting, or network box installation. NO TICE l The OptiXstar P802E belongs to the remote optical access unit (ONU) product series. It is referred to ONU in the following description. l Do not stack horizontally placed ONU. - Page 6 The heat dissipation sides are not allowed to have any contact with the wall or desktop. Mounting on the desktop Do not stack the device when it is placed on the desktop. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd.
- Page 7 8 mm, and the length should not be less than 20 mm. Use a screwdriver to fasten the screws into the expansion bolts, reserving 5 mm ends out of the wall, and mount the ONU onto the screws. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd.
- Page 8 "5" means that the water sprayed from different directions to the network box does not damage the device.) l The method for installing the ONU in a non-Huawei network box depends on the network box specifications. When the ONU is installed in a non-Huawei network box, the preceding heat dissipation space rules must be observed.
- Page 9 – Use the ground cable (the cross-sectional area of the ground cable must be greater than or equal to 6 mm2) to connect the ground bar and all the internal devices, and Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd.
- Page 10 Otherwise, the customer addition, ground the must take consequences. fiber strength member and the network box separately. Install the network box and ONU based on the instructions provided in this document. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd.
- Page 11 Use a piece of sandpaper to polish burrs at the stripped position of the optical cable. Then, use insulation tape to wrap the stripped optical cable. When wrapping the waterproof tape, ensure that fiber cores are force-free. iii. Cut excess fiber strength member for grounding. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd.
- Page 12 Otherwise, heavy currents may be discharged using the network ports on the local and peer devices, which may damage these network ports. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd.
-
Page 13: Connecting Cables
Connect to a PC, IP STB or camera to support 10Mbit/s or 100Mbit/s or 1000Mbit/s interface rate adaptation. Power Connects to a power adapter. On/Off Powers the ONU on or off. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd. -
Page 14: Description Of Indicator
Blinks twice The ONT attempts to set up a connection with its a second upper-layer device. Steady on A connection is set up between the ONT and its upper-layer device. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd. - Page 15 Blinks once The ONT is not connected to fibers or does not every 2 seconds receive optical signals. Blinks once Blinks once The hardware is faulty. every 2 every 2 seconds seconds Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd.
-
Page 16: Technical Specifications
Power adapter input 11V to 14V (typical 12 V), 1A System power supply 100V to 240V AC, 50/60Hz Maximum system power consumption Operating temperature -40°C to +55°C Operating humidity 5%RH to 95%RH (non-condensing) Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd. -
Page 17: Faqs
If the LOS indicator blinks twice a second, the ONU is prohibited by the upper-layer device or blinks abnormally. Contact the service provider for help. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd. - Page 18 The PON indicator is off. Check whether the optical port and optical fiber is properly connected. The ONU fails to register with the upper-layer device. Contact the service provider for help. Issue 01 (2019-09-30) Copyright © Huawei Technologies Co., Ltd.