Fujitsu ETERNUS DX S4 Series Safety Precautions page 4

•
Do not pour or spill water on this device.
Do Not Wet
Doing so may cause electric shock, fire, or
device failure.
•
When unplugging the power plug, do not pull
Unplug
on the cable, hold the plug. Pulling the cable
may expose or snap the inner wires, which can
lead to electric shock and/or fire.
•
Use a dry cloth to remove all dust from plugs
and sockets. Not doing so may cause electric
shock and/or fire.
•
When this device is not used for a long period
of time, unplug all power plugs. Failure to do
so may lead to fire.
•
When the cover of this device is opened or
Warning
other moving parts are operated, make sure
not to touch the projection in this device. This
could both damage this device and cause
injury.
CAUTION
•
Avoid handling this device roughly or
Do Not
subjecting it to physical shocks when pulling it
out or pushing it into a rack or while the top
board of a drive enclosure is being opened or
closed. Doing so may damage this device.
•
When this device is pulled out from the rack,
make sure not to hit your head if you are
operating devices under this device. Not doing
so may cause injury.
•
The FC, iSCSI (10Gbit/s), Ethernet (10Gbit/s),
and FCoE are Class1 LASER products. Normally,
they have no affect on the human body, but
do not look at the laser beam directly. Doing
so may damage your eyes.
•
Do not put your finger into the inlet/outlet.
Doing so may cause injury or device failure.
•
Do not remove the cover from this device
inlet/outlet unless necessary. Doing so may
cause device failure.
•
Do not use devices such as mobile phones
that emit radiation in the vicinity of this
device. Doing so may cause malfunction.
•
Before applying insecticides for pest control,
Do
turn off this device and cover it with a plastic
sheet. Not doing so may damage this device.
•
Note the following points when cleaning this
device. Failure to do so may cause device
failure.
-
Make sure this device is turned off.
-
Do not allow liquids such as cleaner to get
into this device.
-
Never use organic solvents such as
alcohol or thinner to clean this device.
Instructions for rack installation
CAUTION
•
When installing this device in the rack, two or
Do
more (appropriate numbers) people are
needed. Do not install a heavy device without
two or more people. Doing so may cause
injury and/or damage this device.
•
Especially for an enclosed rack with doors, or
when multiple devices are to be mounted and
running, it is important to realize that the
temperature inside the cabinet will be
considerably higher than that of the room.
Make sure the rack internal ambient
temperatures do not exceed the
environmental conditions for temperature
described in the manuals of the devices that
are being used. Failure to do so may damage
this device.
•
When installing this device with other devices
into the same rack, the airflow of the device
installed on and under this device may
interfere with each other and reduce the effect
of device cooling. Make sure to leave plenty of
room between the devices if required. Failure
to do so may damage this device and lead to
malfunction.
•
When installing this device in a rack, be
careful not to pinch your fingers in the rack.
Doing so may cause injury.
•
When installing devices in a rack, make sure
to install them starting from the bottom of the
rack and working upward to ensure the center
of gravity is maintained. If the bottom of the
rack is empty and devices are only installed at
t he to p o f t h e ra ck , t he rack b e co m es
unstable, which may cause injury and damage
the devices.
•
Install the blank panels provided with the rack
where no other devices are installed. Failure
to do so may cause this device to overheat,
resulting in damage to the device.
•
When moving the rack after installing this
device, make sure to contact your sales
representative or your maintenance engineer.
Do not move the rack by yourself. Doing so
may cause injury and/or damage this device.