Table of Contents
Advertisement
Connections
Power source
Power connection
To DC
AC 120V,
input jack
60Hz
2
3
1
AC adapter
AC cord
(supplied)
(supplied)
20
Basic setup
To memorize channels
This TV/DVD is equipped with a channel memory feature which allows
channels to skip up or down to the next channel set into memory, skipping over
unwanted channels. Before selecting channels, they must be programmed into
the TV/DVD's memory. In addition to normal VHF and UHF channels, this TV/
DVD can receive up to 113 Cable TV channels. To use this TV/DVD with an
antenna, set the TV/CABLE selection to the TV position. When shipped from
the factory, this selection is in the CABLE position.
TV/CABLE selection
1
Press MENU in the TV mode, then press
to select
option.
TV/CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
2
Press
or
to select "TV/CABLE".
TV/CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
3
Press
or
to select "TV" or "CABLE".
TV - VHF/UHF channels
CABLE - Cable TV channels
TV/CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
4
Press MENU repeatedly until the menu screen is
cleared.
Cable TV chart
The chart below is typical of many cable system channel
allocations.
22
TO USE AC POWER
1. Connect the AC cord to the AC adapter.
2. Connect the AC adapter plug into the TV/DVD's DC input jack.
3. Connect the AC cord into a wall outlet.
Notes:
• Make sure to insert the plug of each cord securely.
• During use the AC adapter becomes warm. This is not a
malfunction.
WARNING:
• DO NOT CONNECT THIS UNIT TO THE POWER USING
ANY DEVICE OTHER THAN THE SUPPLIED AC ADAPTER
OR POWER CORD. THIS COULD CAUSE FIRE, ELECTRIC
SHOCK, OR DAMAGE.
• DO NOT USE WITH A VOLTAGE OTHER THAN THE
POWER VOLTAGE DISPLAYED. THIS COULD CAUSE
FIRE, ELECTRIC SHOCK, OR DAMAGE.
CAUTION:
• DO NOT USE THE AC ADAPTER IF IT IS COVERED BY A
CLOTH ETC., OR PRESSED INTO A NARROW AREA.
THIS RESULTS IN POOR DISSIPATION OF HEAT AND
MAY CAUSE FIRE, ELECTRIC SHOCK, OR DAMAGE.
• WHEN THIS UNIT IS NOT USED FOR A LONG TIME,
(E.G., AWAY ON A TRIP) IN THE INTEREST OF SAFETY,
BE SURE TO UNPLUG IT FROM THE WALL OUTLET.
• DO NOT PLUG/UNPLUG THE PLUG WHEN YOUR HANDS
ARE WET. THIS MAY CAUSE ELECTRIC SHOCK.
• IF YOU NEED TO REPLACE THE SUPPLIED AC
ADAPTER OR AC CORD, THE SPECIFIED AC ADAPTER
AND AC CORD MUST BE USED. CONTACT THE DEALER
THAT YOU PURCHASED THE UNIT FROM.
0–9
/ / /
CH +/–
MENU
Automatic memory tuning
or
Press
or
to select the "AUTO CH MEMORY",
then press
.
The TV will begin memorizing all the channels
available in your area.
CABLE
TV/CABLE
AUTO CH MEMORY
ADD/DELETE
/
/
/ MENU
To ADD/DELETE channels
CABLE
1
Press
or
to select "ADD/DELETE", then
press
.
TV/CABLE
AUTO CH MEMORY
ADD/DELETE
/
/
/ MENU
2
Select the desired channel to be added or
TV
deleted using Direct channel selection (0–9) or
CH +/–.
3
Press
or
to select "ADD" or "DELETE",
whichever function you want to perform.
ADD
0-9
/
/
/
/
Basic setup
Setting the language
This TV/DVD can display the on screen language in English, Spanish or French
in the TV mode.
Select the language you prefer first, then proceed with the other menu
options.
Setting the language
1
To turn on the TV/DVD, press POWER.
The Power indicator on the front of the main unit
will light.
2
Press MENU, then press
option.
3
Press
or
English (ENGLISH), Spanish (ESPAÑOL) or
French (FRANCAIS), then press ENTER.
4
Press MENU repeatedly until the menu screen
is cleared.
Notes:
• If the unit does not operate properly, or No key operation
(by the unit and/or the remote control): Static electricity,
etc., may affect the TV/DVD's operation. In such case,
disconnect the AC cord once, then connect it again.
• The TV section has its own menu and also DVD section has
its own menu
.
43
TV operation
TV operation
TV operation
1
To turn on the TV/DVD, press POWER.
The Power indicator on the front of the main unit
will light.
CABLE
2
Adjust the volume level by pressing VOL + or –.
The volume level will be indicated on the
screen by green bars. As the volume level
increases, so do the number of bars. If the
volume decreases, the number of green bars
also decreases.
CABLE
3
Set the TV/CABLE selection to the appropriate
position.
22
Auto power off
If a station being viewed stops broadcasting, the TV will
automatically shut itself off after 15 minutes.
CH 001
/ MENU
or
to select
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
FRANCAIS
/MENU
to select the desired language:
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
FRANCAIS
/
/ ENTER/MENU
4
Press direct channel selection (0–9) to select
the channel.
TV mode direct channel selection
When the TV/CABLE selection is in the TV
position, all channels can be instantly selected by
using two buttons. (for example, to select channel
2, press "0", then "2".
If you press only "2",
channel selection will
be delayed for a few
seconds.) For
channels 10 and
above, press the 2
digits in order.
CABLE mode direct channel selection
When the TV/CABLE selection is in the CABLE
position, channels can be selected as follows:
TO SELECT CABLE TV CHANNELS:
1-9:
10-12:
VOLUME
32
13-99:
100-125: Press the 3 digits in order. Example, to
NOTE FOR CHANNELS 1-12:
If only 1 or 2 buttons are pressed, the corresponding
TV
- VHF/UHF channels
channel will be selected in 2 seconds.
CABLE - Cable TV channels
TV
VHF
2-13
UHF
14-69
Note:
If a channel with no broadcast is selected, the sound will
automatically be muted.
POWER
ENTER
/ / /
MENU
21
POWER
0–9
VOL +/–
CH 02
Press "0" twice, then 1-9 as needed.
Example, to select channel 2, press
"002".
Press "0", then the remaining 2 digits.
Example, to select channel 12, press
"012".
Press the 2 digits in order. Example, to
select channel 36, press "36".
select channel 120, press "120".
CATV
VHF
2-13
STD/HRC/IRC
14-36
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
(5A)
23
Advertisement
Table of Contents
