DeWalt DCR017 Manual page 11

2. Press Enter/Display to select.
7
3. Scroll right to the Yes option, then press the Enter/Display
button to prune stations.
DAB Mode – Dynamic Range Compression (DRC)
This function reduces the difference between the loudest
and quietest audio being broadcast. Effectively, this makes
quiet sounds comparatively louder, and loud sounds
comparatively quieter.
The following options are available:
0 - broadcast DRC will be ignored
1/2 - sets DRC at half the level transmitted
1 - uses the DRC level transmitted
2 - doubles the DRC level transmitted
nOTE: DRC only works if it is enabled by the broadcaster.
FM Mode – Tuning
To Tune: Push the right arrow to move the tuner up the
frequency band, push the left arrow to move the tuner down
the frequency band.
To seek: Press and hold the right arrow button
release. The tuner frequency will increase to seek the first radio
station with acceptable clarity and stop at that station. The
right arrow button may be pressed again to continue seeking a
radio station at higher frequencies. The left arrow button may
be pressed to seek radio stations at lower frequencies. The seek
function is available in FM mode.
Programming the Memory Buttons
Ten DAB and ten FM radio stations may be independently set.
After programming the buttons, pressing 1, 2, 3, 4 or 5 will
instantly change the frequency to the preset station.
1. Set the radio to desired station (see Tuning).
2. Press and hold one of the desired memory buttons
the preset number begins flashing in the LCD display
Release the button and wait for the preset display to
stop flashing.
3. Each memory button can store two preset stations. To store
a second preset repeat step 1.
4. Press and hold one of the desired memory buttons
the preset number begins flashing in the LCD display
Press the preset button a second time so that the next
preset number displays. Release the button and wait for the
preset display to stop flashing.
Programming the Clock
The time and date can be updated manually or automatically
synchronised with national time signals broadcast over
DAB (where available).
To synchronise the Clock Automatically:
(DAB mode ONLY)
nOTE: When the radio is first used it will enter DAB mode and
automatically scan for stations.
1. Press the Menu button 5 .
2. Use the arrow buttons 3 to scroll to Clock Adjust and press
the Enter/Display button 7
3 once and
6 until
8 .
until
6
8 .
.
3. Scroll to Sync Time Now press the Enter/Display button to
select. This automatically synchronises clock with national
7
time signals.
To Adjust the Clock Manually:
(FM and DAB mode)
1. Press the Menu button
2. Use the arrow buttons
display and press the Enter/Display button
3. Scroll to Date & Time and press the Enter/Display button
4. Set the date and time using left and right arrow buttons
5. Once the desired time is set press the Enter/Display
button to commit.
Other Clock Adjust menu options:
• Time format: Select a 12h or 24h time display format
• Date format: Select the date display format, MM/DD/YYYY,
YYYY/MM/DD or DD/MM/YYYY.
To Adjust the EQ
Sound can be adjusted by changing the equalization of the bass
or treble of the radio.
1. Press the Menu button
arrow buttons 3 to select Sound EQ. Select by pressing the
Enter/Display button
2. Press the right arrow button to increase the bass or the left
arrow button to decrease it.
3. Once desired adjustment is achieved, press the Enter/
Display button 7 .
4. Repeat steps 2 and 3 for treble adjustment.
Important Radio Notes
1. The radio will run up to 8 hours on a fully charged 4.0 amp
hour battery. Using batteries of lower voltage or capacity
will result in less run time.
2. Reception will vary depending on location and strength of
radio signal.
3. Certain generators may cause background noise.
4. To use the auxiliary port
CD or iPod®*/MP3 player into the port (Fig. A). The sound
from the external source plays through the speakers of
the DCR017.
5. The USB power output port
powering low power devices such as mobile phones, CD
and MP3 players.
* iPod is a registered trademark of Apple Inc.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
English
5 .
3 to scroll to Clock Adjust on the LCD
.
7
5 and scroll using the left or right
7 .
11 , plug the output jack from a
16 is a connection port for
7 .
3 .
7
9