Cooling Mode; Dehumidifying Mode - Black & Decker BXAC12001E Instruction Manual

ENGLISH (Original instructions)
appliance.
♦ Do not cover or obstruct the sides of the appliance,
and leave a minimum space of 50cm front other walls,
ceiling..
♦ The plug must be easily accessible so it can be discon-
nected in an emergency.
♦ To achieve the highest efficiency from the appliance
it should be situated in a place where the atmospheric
temperature is between 12 and 32ºC.
♦ Ensure that the extraction pipe remains in a horizontal
position. (Fig 2)
♦ Do not add new sections to the extraction tube provided,
as it could cause the appliance to malfunction.
♦ The appliance should be used with its base feet fitted.
♦ The appliance should be used with its wheels attached.
Assembly of the exhaust hose
♦ Lengthen one head of the hose, and spin the exhaust
hose into exhaust connector (counterclockwise).
♦ Caution: Exhaust pipe is 40 cm~160 cm long (including
adapter).
♦ The length of exhaust pipe is especially designed in
accordance with the specification of the air conditioner.
Please do not use other exhaust pipes of different leng-
ths or materials, in such way failure may be caused.
INSTALLATION OF WINDOW KIT (Fig 3)
♦ Partially open the window and then fix the window kit to
the window.
♦ The window kit can be installed on most of normal and
vertical windows and it is adjustable.
♦ Fix the other end of the heatexhausted hose to the
airoutlet window kit.
Instructions for use
Use:
♦ Unroll the cable completely before plugging it in.
♦ Connect the appliance to the mains.
♦ Press the ON/OFF button, the unit will enter in cooling
mode with low fan speed.
♦ Press the mode button to select cooling dehumidifying,
fan mode.
Fan Speed
♦ Under the cooling and the fan mode, the speed goes as
follow:
♦ Lower Fan→Mid Fan> High Fan.
♦ Temperature cannot be set.
8
Timer mode
♦ In standby mode, press time button to set time start.
Press the upanddown button to the time of start (0~24
hours), and time indicator light is on.
♦ In startup mode, press time button to set time switchoff.
♦ Press the upanddown button to the time of switchoff
(0~24 hours), and time indicator light is on.
Swing
♦ Press this button to control the movement of the louver.

Cooling mode:

♦ Press mode to select cooling mode, cooling mode
indicator turns on.
♦ Press Up or Down to adjust temperature in a range of
17ºC~30ºC.
♦ When the up or down is pressed once, temperature will
go up or down by 1ºC every time.
♦ Press speed to select high, mid or low fan speed.
Heat mode
♦ Press mode (d) to select heat mode, the Heat mode
indicator will light.
♦ Press (c) to adjust the temperature.
♦ Pulsa speed (b) to increase or decrease speed.
Fan mode:
♦ Press mode to select fan mode fan indicator turns on.
♦ Press speed to select high, mid or low speeds.
♦ Temperature is not adjustable.

Dehumidifying mode:

♦ Press "MODE" to select dehumidifying mode, dehumidif-
ying mode indicator turns on.
♦ Remove the plug of drainage cap, insert a tube and put
the other side of the tube into water containers or drain
channels.
♦ When entering dehumidification mode, if the room tem-
peratures is ≥17ºC, the compressor will start to work.
♦ If the room temperature is ≤15ºC, compressor stops;
when the temperature rises back to ≥17ºC, the com-
pressor restarts (the compressor shall meet the 3minute
delay protection function).
♦ In dehumidification mode, the fan run in low speed by
default, and the wind speed are not adjustable. ·Tempe-
rature cannot be set.
♦ NOTE: When the dehumidification function is in use, the
exhaust pipe assembly shall be removed; otherwise it
will lead to not obvious dehumidification effect or display