Sealey SA672.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT please read These insTrUcTions careFUllY. noTe The saFe operaTional reQUireMenTs, Warnings and
caUTions. Use This prodUcT correcTlY and WiTh care For The pUrpose For Which iT is inTended. FailUre To do so MaY
caUse daMage or personal inJUrY and Will invalidaTe The WarranTY. reTain These insTrUcTions For FUTUre Use.
1. saFeTY insTrUcTions
 Follow all workshop Health & Safety rules, regulations and conditions when using this tool.
 Warning! Disconnect the grinder from the air supply before changing accessories, servicing or performing any maintenance.
 Maintain the grinder in good condition and replace or repair any damaged or worn parts. Use genuine parts only. Unauthorised parts may
be dangerous and will invalidate the warranty.
 Warning! Ensure the correct air pressure (90psi) is maintained and not exceeded.
 Keep hoses away from heat, oil and sharp edges. Check hoses for wear before each use. Make certain that all connections are secure.
 Warning! Before each use check abrasive attachment is secure and that it is not worn or damaged. If damaged, replace immediately.
 Ensure replacement grinding bits are not damaged (cracks, deformations or splinters etc.).
 Always use the correct grinding bit for the material being ground. Ensure the maximum speed of the bit is equal to or higher than the
maximum of the die grinder.
 Ensure there are no flammable or combustible materials near the work area.
 Always wear approved safety eye protection, ear defenders, safety gloves and if dust or fumes are generated, appropriate respiratory
protection in accordance with COSHH regulations must be used.
 Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery and contain long hair.
 Locate the grinder in an adequate working area for its function, keep area clean, tidy, free from unrelated materials and ensure there is
adequate lighting.
 Maintain correct balance and footing, do not over reach. Ensure the floor is not slippery and wear non slip shoes.
 Keep children and unauthorised persons away from the working area.
 Secure non stable workpiece with a clamp, vice or other adequate holding device and do noT hold unsecured work in your hand.
 Avoid subjecting the grinding bit to excessive strain, always ease the grinding bit onto the workpiece.
 do noT place attachments close to your face and do not point at other persons or animals.
 do noT force the grinder to achieve a task it was not designed to perform.
 do noT operate the grinder when you are tired, under the influence of alcohol, drugs or intoxicating medication.
 do noT allow untrained persons to operate the grinder
 do noT direct air from from the air hose at yourself or others..
 do noT use the grinder where there are flammable liquids, solids or gases such as paint solvents, etc.
 do noT start the grinder with the grinding bit in contact with the workpiece.
 do noT leave the die grinder connected to the air supply whilst unattended.
 do noT carry the by the hose, or yank the hose from the air supply.
 do noT touch the workpiece close to the ground surface as it will be very hot, allow to cool and take care as sharp edges may be present.
 When not in use switch the grinder off, disconnect from the air supply, and store in a safe, dry, child proof area.
risk of hand arm vibration injury.
The SA672.V2 Long Reach Air Die Grinder, when operated in accordance with these instructions and tested in accordance with EN 28662-1:
1993 results in the following vibration emission declared in accordance with BS EN12096: 1996.
Measured vibration emission value: . . . . . . . . . 5.0m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
recommended Measures to reduce risk of hand-arm vibration syndrome:
This tool should not be used by an individual regularly for more than 244 minutes in any 8 hour period.
This duration of use should be reduced if the individual is exposed to hand-arm vibration from other sources.
2. speciFicaTion
One handed, straight type die grinder with machined aluminium body and trigger with safety catch. Long reach head chuck accepts grinding
points with Ø6mm shanks. Supplied with two spanners.
Collet size. . . . . . . . . . . . . . . . . 6mm
Free speed . . . . . . . . . . . . . . . . 25000rpm
Air consumption . . . . . . . . . . . . 4cfm
Operating pressure. . . . . . . . . . 90psi
Air inlet size . . . . . . . . . . . . . . . 1/4" BSP
Length. . . . . . . . . . . . . . . . . . . . 235mm
Weight . . . . . . . . . . . . . . . . . . . 0.7kg
A-weighted sound. . . . . . . . . . . 94dB
C-weighted sound . . . . . . . . . . 106dB
Vibration level . . . . . . . . . . . . . . 5.0m/s²
INSTRUCTIONS FOR:
long reach air die grinder
MODEL No:
Uncertainty: . . . . . . . . . . . . . . . . . . 2.0m/s²
Original Language Version
sa672.v2
SA672.V2 Issue: 3 - 11/11/09