COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-29 FACTORY MODEL: LB800H MODEL: ) ID LABEL MODEL No. CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html L1810B(LB800H-UL)
Signal Connector Pin Assignment • DVI-I Connector (Digital/Analog) Signal (DVI-I) T. M. D. S. Data2- T. M. D. S. Data2+ T. M. D. S. Data2/4 Shield T. M. D. S. Data4- T. M. D. S. Data4+ DDC Clock DDC Data Analog Vertical Sync.
WARNING FOR THE SAFETY-RELATED COMPONENT. • There are some special components used in LCD monitor that are important for safety. These parts are marked on the schematic diagram and the replacement parts list. It is essential that these critical parts should be replaced with the manufacturer’s specified parts to prevent electric shock, fire or other hazard.
OPERATING INSTRUCTIONS FRONT VIEW Front Control Panel 1. Power ON/OFF Button Use this button to turn the monitor on or off. 2. Power Indicator This indicator lights up green when the monitor operates normally. If the display is in DPM(Energy Saving)mode, this indicator color change to amber.
Making use of USB (Universal Serial Bus)* USB (Universal Serial Bus) is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and other to your monitor instead of having to connect them to your computer.
DESCRIPTION OF BLOCK DIAGRAM 1. Input signal switching part(BA7657). There are two anolog inputs which are D-Sub analog and DVI-anolog input. They come from each 15 pin D-Sub and 29 pin DVI-I connector. 2. Video Controller Part(GM5020). This part amplifies the level of video signal for the anolog to digital conversion and converts from the analog video signal to the digital video signal using a pixelclock.
Page 11
50 ~ 60Hz COMPONENTS LINE 100 ~ 240V Operation description_Power 1. EMI components. This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the circuit included a line-filter, across line capacitor and of course the primary protection fuse. 2.
All adjustment are thoroughly checked and corrected when the monitor leaves the factory, but sometimes several minor adjustment may be required. Adjustment should be following procedure and after warming up for a minimum of 10 minutes. • Alignment appliances and tools. - IBM compatible PC - Programmable Signal Generator.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK J801 INPUT VOLTAGE (12V) ? CHECK J801 5VST VOLTAGE (5V) ? CHECK U501’s PIN 6. IS THIS PIN OSCILLATED? TROUBLE SOMEWHERE ELSE TROUBLE IN BULT-IN POWER TROUBLE IN BULT-IN POWER TROUBLE IN U501 or X501 - 13 -...
Page 14
2. NO RASTER NO RASTER CHECK J702 PIN 1, 2, 3 (12V) ? CHECK J702 PIN 8 (5V) ? CHECK X501 H. PULSE ? CHECK U201(GM5020) ? CHECK L201, L202, L203 PULSE? CHECK U301, U302, U303 PIN 35 MEMORYCLK? TROUBLE IN POWER ADATER or L703, L704 TROUBLE IN...
Page 16
3. NO CLOCK (CLOCK GENERATOR) NO DOT CLOCK CHECK X201 24MHz ? CHECK L201 CLOCK ? TROUBLE IN X201 TROUBLE IN U201 - 16 -...
Page 17
4. TROUBLE IN DPM TROUBLE IN DPM CHECK R233, R234? CHECK U501 PIN 6 WAVEFORM (24MHz) ? CHECK U501 PIN 11 (0V) ? TROUBLE IN PC CHECK PC PC IS NOT GOING INTO DPM OFF MODE TROUBLE IN X501 TROUBLE IN SIGNAL CABLE - 17 -...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION MAIN BOARD CAPACITORS C106 0CC101CK41A 100PF 1608 50V 5% R/TP NP0 C107 0CC101CK41A 100PF 1608 50V 5% R/TP NP0...
GM5020 FUNCTIONAL BLOCK DIAGRAM Serial I/F Host Interface Anolog Triple Image Digital TMDS Caputure/ TMDS Measure. Input ment Video [8-bits] SYSTEM BLOCK DIAGRAM Anolog Composite S-Video PIN CONFIGURATION GENESIS 292P SDRAM/I/F Micro- Frame Store processor Interface YUV to RGB Converter Zoom/ Frame Rate Brightness,...
Page 31
DIP Package(p) SOIX Package(J) V CC V SS V SS TSSOP Package(U) V SS PIN CONFIGURATION PIN FUNCTION Pin Name Function A0, A1, A2 Device Adress Inputs Serial Data/Address Serial Clock Write Protect +1.8V to + 6.0V power Supply Ground CAT24WC08J-TE13 8P BLOCK DIAGRAM EXTERNAL LOAD...