Page 1
MCM148 Micro Hi-Fi System Register your product and get support at www.philips.com/welcome User manual 用戶手冊...
Page 2
CAUTION Use of controls or adjustments or perfor- mance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
Page 4
Index English ---------------------------------------------------- 6 中文 --------------------------------------------- 第 21 頁...
Contents General Information Supplied accessories ...7 Environmental Information...7 Safety Information ...7 Hearing Safety ...8 Preparations Rear connections ...9 Inserting batteries into the Remote Control..10 Using the Remote Control to operate the system ...10 Controls Controls on the system and remote control ..11 Controls available on the remote control only ...
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/ welcome. IMPORTANT! PLEASE NOTE THAT THE VOLTAGE SELECTOR LOCATED AT THE REAR OF THIS SYSTEM IS PRESET AT 110V FROM THE FACTORY. FOR...
General Information Hearing Safety Listen at a moderate volume. ● Using headphones at a high volume can impair your hearing. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute.
Rear connections The type plate is located at the rear of the system. A Power – Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. – If your system is equipped with a Voltage Selector, set the VOLTAGE SELECTOR to the local power line voltage.
Preparations Inserting batteries into the Remote Control Open the battery compartment. Insert two R03 or AAA batteries following the indications (+/-) inside the compartment. Close the cover. Using the Remote Control to operate the system Aim the Remote Control directly at the remote sensor (IR) on the front panel.
Controls on the system and remote control 1 STANDBY ON 2 (PWR) – switches the system to standby or on. 2 iR SENSOR – infrared sensor for remote control. 3 SOURCE – selects the respective sound source for CD/ TUNER/AUX. –...
Basic Functions STANDBY-ON MICR O SYSTE M MCM148 MP3-CD/CD - R/CD - RW COMPATIBLE SOURC E ALBUM/ PRESET TUNING IMPORTANT: Before you operate the system, complete the preparation procedures. Plug and Play (for tuner installlation) Plug and Play allows you to store all available radio stations automatically.
STANDBY-ON MICR O SYSTE M MCM148 MP3-CD/CD - R/CD - RW COMPATIBLE SOURC E ALBUM/ PRESET TUNING IMPORTANT: The lens of the CD player should never be touched. Loading a disc This CD player plays Audio Discs including CD- Recordables, CD-Rewritables and MP3 CD.
CD/MP3 Operation Press TUNING 4 ¢ (on the remote control ¡ / ™ ) to select a desired track. Press 2; to start playback. ● During playback, press CLOCK/DISPLAY on the remote control to show the title name, album name, ID3 information and clock time. Supported MP3 disc formats: –...
STANDBY-ON MICR O SYSTE M MCM148 MP3-CD/CD - R/CD - RW COMPATIBLE SOURC E PRESET ALBUM/ TUNING Tuning to radio stations Press SOURCE on the set repeatedly or press TUN on the remote control repeatedly until the desired waveband (FM or MW) is displayed.
AUX on the remote control to select AUX source. Use a cinch cable (not supplied) to connect MCM148’s AUX jack (3.5 mm, located on the back panel) to an AUDIO OUT or headphone jack on an external equipment (such as CD player, or VCR).
STANDBY-ON MICR O SYSTE M MCM148 MP3-CD/CD - R/CD - RW COMPATIBLE SOURC E ALBUM/ PRESET TUNING Setting the clock In standby mode, press and hold CLOCK/ DISPLAY on the remote control set for 2 seconds. Press PROG. to select 12-hour or 24-hour display.
Specifications AMPLIFIER Output power ...2 x 2W RMS Signal-to-noise ratio ... ≥ 60 dBA (IEC) Frequency response ... 125 – 16000 Hz Impedance loudspeakers ...4 Ω CD PLAYER Frequency range ... 125 – 16000 Hz Signal-to-noise ratio ...65 dBA TUNER FM wave range ...87.5 –...
If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help. Problem “NO DISC”...
Troubleshooting Problem The remote control does not function properly. The time is not working. The Clock/Timer setting is erased. Solution Select the source (CD or TUNER, for example) ✔ before pressing the function button ( É , í , ë ). Reduce the distance between the remote ✔...
Meet Philips at the Internet http://www.philips.com MCM148 CLASS 1 LASER PRODUCT C 2009 Koninklijke Philips Electronics N.V. All rights reserved. MCM148_96_UM_V1.0...