Sealey SA624 Instructions

Item Part No
Item Part No Description
1 SA624/01 MOTOR HOUSING
27 SA624/27 BUSHING
2 SA624/02 SPRING PIN
28 SA624/28 PIN
3 SA624/03 DAMPING MATERIAL
29 SA624/29 REDUCTION SPINDLE
4 SA624/04 EXHAUST DIFFUSER
30 SA624/30 CENTRE GEAR
5 SA624/05 AIR INLET
31 SA624/31 WORK SPINDLE
6 SA624/06 SCREW
32 SA624/32 SPRING
7 SA624/07 RUBBER GRIP
33 SA624/33 SPRING GUIDE
8 SA624/08 MOTOR GASKET
34 SA624/34 INTERNAL GEAR
9 SA624/09 BALL BEARING
35 SA624/35 BALL BEARING
10 SA624/10 END PLATE
36 SA624/36 CLAMP NUT
11 SA624/11 SPRING PIN
37 SA624/37 DRIVE DOG
12 SA624/12 CYLINDER
38 SA624/38 RETAINING RING
13 SA624/13 ROTOR BLADE
39 SA624/39 RETAINING RING
14 SA624/14 ROTOR 40 SA624/40 CAM SPINDLE
15 SA624/15 O-RING
41 SA624/41 STEEL BALL
16 SA624/16 REVERSE BUSHING
42 SA624/42 CLUTCH CARRIER
17 SA624/17 O-RING
43 SA624/43 STEEL BALL
18 SA624/18 REVERSE RETAINER
44 SA624/44 WASHER
19 SA624/19 REVERSE LEVER
45 SA624/45 SPRING
20 SA624/20 VALVE STEM SET
46 SA624/46 WASHER
21 SA624/21 VALVE SPRING
47 SA624/47 ADJUST NUT
22 SA624/22 SET SCREW
48 SA624/48 SPACER
23 SA624/23 TRIGGER
49 SA624/49 CLUTCH HOUSING
24 SA624/24 SPACER
50 SA624/50 BALL RETAINER
25 SA624/25 PINION GEAR
51 SA624/51 SPRING
26 SA624/26 PLANET GEAR
52 SA624/52 WASHER
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date. proof of which will be required for any claim. INFORMATION: Call us for a copy of our latest catalogue
and promotions on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500
Description
Original Date: 010700
Issue Date: 010700
Version No: 0
Date Modified: N/A
01284 703534
E-mail: sales@sealey.co.uk
INSTRUCTIONS FOR
AIR PISTOL SCREWDRIVER
SA624
Model:
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
3 Follow all workshop health & safety rules, regulations, and conditions when using screwdriver.
p WARNING! Disconnect from air supply before changing accessories or servicing.
3 Maintain screwdriver in good condition and replace any damaged or worn parts. Use
genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
p WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
Wear approved safety eye and ear protection.
Keep screwdriver bits clean and in good condition for best and safest performance.
3
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure non stable work piece with a clamp, vice or other adequate holding device.
Ensure the screwdriver bit is secure in the chuck.
3
Avoid unintentional starting.
3
3 Keep children and unauthorised persons away from the working area.
3
DO NOT get the screwdriver wet or use in damp or wet locations.
DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
8
7 DO NOT use the screwdriver for a task it is not designed to perform.
8
p WARNING! DO NOT use screwdriver if damaged or faulty. Contact your local service agent).
7 DO NOT use screwdriver unless you have been instructed in its use by a qualified person.
7 DO NOT drop, throw or abuse the screwdriver.
7 DO NOT carry the screwdriver by the air hose, or yank the hose from the air supply.
7 DO NOT operate screwdriver if you are tired, under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT carry screwdriver with your hand on the power trigger in order to avoid unintentional starting.
7 DO NOT direct air from the air hose at yourself or others.
3 When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATIONS
Fully polished finish with exhaust through handle base for reduced noise emission. Smooth air motor
runs on high quality ball bearings for long life and reliability. Fully reversible drive with finger-tip
control set above trigger. Fully adjustable torque between 45 and 145 ins/lb. Accepts 6mm hex
driver bits. Rubber grip gives added control.
Chuck size . . . . . . . . . . . . .1/4” - 6mm
Free speed . . . . . . . . . . . . . . .720rpm
Torque range . . . . . . . . . . .45-145In/lb
Air consumption . . . . . . . . . . . . . 4cfm
Operating pressure . . . . . . . . . . .90psi
Air inlet size . . . . . . . . . . . . . 1/4” BSP
Weight . . . . . . . . . . . . . . . . . . . .1.4kg
SA624 - 0016 - (2) -130700