Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Refer to the diversity tables for the correct values. two pins of the Mains/AC Power plug. • The correct component values are listed on the Philips • Check the cabinet for defects, to prevent touching of any Spare Parts Web Portal.
Page 6
• Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to avoid mixed regimes. If this cannot be avoided, carefully clear the solder-joint from old tin and re-solder with new tin.
Page 7
originating from the USA and used e.g. in • Always respect voltages. While some may not be dangerous in themselves, they can cause unexpected LATAM and AP-NTSC countries reactions that are best avoided. Before reaching into a B-TXT Blue TeleteXT powered TV set, it is best to test the high voltage Centre channel (audio) insulation.
Page 8
G-TXT Green TeleteXT distance is 6.5 MHz. L' is Band I, L is all H_sync to the module bands except for Band I High Definition LG.Philips LCD (supplier) Hard Disk Drive Loudspeaker HDCP High-bandwidth Digital Content Protection: LVDS Low Voltage Differential Signalling A “key”...
Page 9
Serial Peripheral Interface bus; a 4-wire module, implementing the CA system for a synchronous serial data link standard host (e.g. a TV-set) S/PDIF Sony Philips Digital InterFace Power On Reset, signal to reset the uP SRAM Static RAM PSDL Power Supply for Direct view LED...
Page 10
Thin Film Transistor toward external amplifier Total Harmonic Distortion Vestigial Side Band; modulation method TMDS Transmission Minimized Differential WYSIWYR What You See Is What You Record: record Signalling selection that follows main picture and Transport Stream sound TeleteXT WXGA 1280 × 768 (15:9) TXT-DW Dual Window with TeleteXT XTAL...
3.2 Assembly/Panel Removal 3.2.1 Stand removal Notes: Figures below can deviate slightly from the actual situation due to the different set executions. Remove the fixation screws [1] that secure the stand. Take the stand bracket out from the set. (5303 series) (5403 series)
Page 15
3.2.2 Rear Cover Warning: Disconnect the mains power cord before removing the rear cover. Releasing the clips carefully at the indicated areas [2] that secure the back cover. Unplug connector [3] carefully, as the speaker is catch on back cover. Gently lift the rear cover from the TV.
Page 16
3.2.3 Small Signal Board (SSB) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the SSB. Unplug all connectors [2] from the SSB. Remove all the fixation screws [3] from the SSB. The SSB can now be shifted from side connector cover, then lifted and taken out of the I/O bracket.
Page 17
3.2.6 Speakers Gently release the tapes that secure the speaker cables. Unplug the speaker connector from the SSB. Take the speakers out. When defective, replace the both units. 3.2.7 LCD Panel Remove the SSB as described earlier. Remove the PSU as described earlier. Remove the stand bracket as described earlier.
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM). SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. Some features are: Make alignments (e.g.
Page 19
When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the background). How to Store SAM Settings To store the settings changed in SAM mode (except the RGB Align settings), leave the top level SAM menu by using the POWER button on the remote control transmitter or the television set.
Page 20
Factory mode overview How to Exit the Factory mode Use one of the following methods: Select EXIT_FACTORY from the menu and press the “OK” button. Note: When the TV is switched “off” by a power interrupt, or normal switch to “stand-by” while in the factory mode, the TV will show up in “normal operation mode”...
Page 21
CSM Overview How to Navigate By means of the “CURSOR-DOWN/UP” knob (or the scroll wheel) on the RC-transmitter, can be navigated through the menus. How to Exit CSM To exit CSM, use one of the following methods. Press the MENU/HOME button on the remote control transmitter. Press the POWER button on the remote control transmitter.
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading 5.1.1. The following update is for .pkg file. Rename the file to “upgrade_loader.pkg”. Prepare a USB memory (File format: FLAT, Size: 1G~8G). Copy the software to USB flash disk (root directory). Switch off the TV and Insert the USB memory stick that contains the software update files in one of the TV’s USB 2.0 port.
Page 23
Press [Start] to start software upgrade Upgrade in progress. After software upgrade complete, select [Restart] to reboot TV. Step 3: Check the SW version After burning software, TV will restart. Press “123654”, enter Customer Service Mode to check if the software version is correct. Caution: Please make sure that software upgrade is finished before unplug the USB and AC power!
Page 24
5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set. In principle a unique error code is available for every: • Activated (SW) protection. • Failing I2C device. • General I2C error. The last five errors, stored in the NVM, are shown in the Service menu’s. This is called the error buffer. The error code buffer contains all errors detected since the last time the buffer was erased.
Page 25
Press the following key sequence on a standard RC transmitter: “062598” directly followed by MENU and “xxx”, where “xxx” is a 3 digit decimal value of the panel type: see column “Display Code” in below tab. After resetting the Display Code, restart the set immediately. CTN_ALT BOM# Panel Type Display Code 22PFS5303/12 TPM215WF1-WU3101.K 485BE 22PFS5403/12 TPM215WF1-WU3101.K 485BE 22PFT5303/05 TPM215WF1-WU3101.K 485BE...
Trouble shooting 2016年12月10日 2016/4/8 Picture-related Intermittent Ask Photo Picture ? problem ? Menu Smarkt Signal SW latest ? Backlight? issue function? issue SSB+LVDS+Panel Update SW LED working ? PSU/SSB Problem solved ? Sound ? PSU+ Panel Finish SW+SSB...
Page 27
Trouble shooting 2016年12月10日 2016/4/8 Audio/Sound- related Intermittent Sound ? problem ? Setting SW latest ? Mute ? issue issue Update SW Extra device Check extra connect? device Problem solved ? Factory setting Finish Sound back ? Setting issue SSB+SPK...
Page 28
6.Slow response to user interaction 7.Switches ON by itself 8.Switches Off by itself 9.Stuck in standby mode / unable to start up 10.Stuck on PHILIPS / ANDROID logo 11.CAM not recognized by TV 12.CAM authentication issue 13.Misc CAM issue 14.IP-EPG issues 15.BC-EPG issues...