Table of Contents
Advertisement
Intermittent mode
The intermittent function automatically switches on the extractor
hood for 10 minutes every hour. After 24 hours, this function
switches itself off again.
Note: If intensive mode or the run-on function has been
activated, the intermittent function will not be available.
Switching on
Press and hold the
K
button on the remote control or button 2
on the extractor hood's control panel.
Button 1 on the extractor hood's control panel flashes. The
intermittent function is now on. The extractor hood starts at fan
setting 1.
Switching off
Press the
"
button on the remote control or the
the extractor hood's control panel.
This switches off the intermittent function.
Run-on function
The run-on function allows the extractor hood to continue
running for a few minutes after it has been switched off. This
eliminates any remaining cooking smells. The extractor hood
will then switch itself off automatically.
Switching on
Note: If intensive mode has been activated, the run-on function
will not be available.
Cleaning and maintenance
:
Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
:
Risk of electric shock!
Penetrating moisture may result in an electric shock. Clean the
appliance using a damp cloth only. Before cleaning, pull out the
mains plug or switch off the circuit breaker in the fuse box.
:
Risk of electric shock!
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use any of the following:
Harsh or abrasive cleaning agents,
■
Cleaning agents with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
High-pressure cleaners or steam cleaners.
■
Wash new sponge cloths thoroughly before use.
Follow all instructions and warnings included with the cleaning
agents.
6
Select the fan setting.
1.
Press the
2.
button 1 on the extractor hood's control panel.
The button for the selected fan setting will flash on the
extractor hood's control panel. The fan will continue to run at
this setting for 30 minutes and then switch off automatically
once this time has elapsed. If the lighting has been switched
on, this will also be switched off once the run-on time has
elapsed.
Switching off
Press the
on the extractor hood's control panel.
This will deactivate the run-on function immediately.
Lighting
#
button on
The lighting will work even if the extractor hood is switched off.
Switching on
Press the
the extractor hood's control panel.
Reducing the brightness
Press and hold the
=
button on the extractor hood's control panel until the
brightness has been reduced.
Switching off
Press the
the extractor hood's control panel.
Area
Stainless steel
Painted surfaces
Aluminium and plas-
tic
Glass
Controls
button on the remote control or press and hold
K
"
or
K
button on the remote control or the
k
button on the remote control or the
k
button on the remote control or the
k
button on the remote control or the
Cleaning agent
Hot soapy water:
Clean with a dish cloth and then dry
with a soft cloth.
Clean stainless steel surfaces in the
grind direction only.
Special stainless steel cleaning prod-
ucts are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Do not use any stainless steel cleaners.
Glass cleaner:
Clean with a soft cloth.
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Risk of electric shock caused by pene-
trating moisture.
Risk of damage to the electronics from
penetrating moisture. Never clean
operating controls with a wet cloth.
Do not use any stainless steel cleaners.
#
button
=
button on
=
button on
Advertisement
Table of Contents
