Kenwood DMX1037S Instruction Manual

Kenwood DMX1037S Instruction Manual

Monitor with receiver
Table of Contents

Advertisement

&CAUTION
Be sure to attach the protective cover and fix with
the screws.
If the protective cover is not attached, this unit
will not turn
on.
&ATTEN:J'ION
Veillez
a
placer le cache de protection et
a
fixer
avec les vis.
Si le couvercle de protection n'est pas installe, cet
appareil ne s'allume pas.
&AEHTUNG
Bringen Sie unbedingt die Schutzabdeckung an
und befestigen Sie sie mit den Schrauben.
Wenn die Schutzabdeckung nicht angebracht ist,
lasst sich das Gerat nicht
einschalten.
&LET'OP
Zorg ervoor dat u de beschermkap bevestigt en
vastmaakt met de schroeven.
Als de beschermkap niet is bevestigd, zal
deze
unit niet ingeschakeld worden.
&
ATTENZIONE
Assicurarsi di applicare ii coperchio di protezione
e di fissarlo con le viti.
Se ii coperchio di protezione none applicato,
questa unita non si accendera.
&
PRECAUCION
Asegurese de colocar la cubierta protectora
y
fijarla con los tornillos.
Si la cubierta protectora no esta colocada, esta
unidad nose encendera.
Protective cover
Couvercle de protection
Schutzabdeckung
Beschermkap
Coperchio d1 protezione
Cub1erta protectora
Certifique-se de que monta a tam pa de protec;ao
ea fixa com os
parafusos.
Se a tam pa de protec;ao nao estiver
colocada,
esta
unidade nao se liga.
&
OCTOPO>KHO!
OfonaTe.JlbHO yCTaHOBIIITe 3al.J..IIIITHYIO KpblWKY
Ill
3aKpen111Te ee BIIIHTaMIII.
ECJ1111 3al.J..IIIITHafl KpblWKa He yCTaHOBJleHa,
yCTpo1kTso He
BKJ1t04111T01.
&UWAGA
Pami~taj,
aby zatozyc pokryw~ ochronnq i
zamocowac jq srubami.
Bez zatozenia pokrywy ochronnej wtqczenie tego
urzqdzenia b~dzie niemozliwe.
&POZOR
Nezapomente nasadit ochranny kryt a
prisroubovat jej.
Pokud ochranny kryt nenasadite a nepripevnfte,
jednotka se
nezapne.
&
VIGYAZAT
Mindenkeppen helyezze fel a vedoburkolatot, es
rogzftse a csavarokkal.
Ha a vedoburkolatot nem helyezte fel, a keszulek
nem kapcsol
be.
&
UPOZORNENIE
Nezabudnite pripoji( ochranny kryt a upevni( ho
pomocou
skrutiek.
Ak sa ochranny kryt
nepripojf,
tato jednotka sa
nezapne.
Tampa de protec;ao
3a1J..11t1THafl Kpb1wKa
Pokrywa ochronna
Ochranny kryt
Ved6burkolat
Ochranny kryt
BSH-033900

Advertisement

Table of Contents
loading

Summary of Contents for Kenwood DMX1037S

  • Page 2 Record the serial number, found on the top of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product.
  • Page 3: Table Of Contents

    Category/Channel search ........35 Wireless Mirroring Operation .......16 Replay ................35 Apple CarPlay Operation ........16 TuneMix™ ..............36 Android Auto Operation ........18 SmartFavorites, TuneStart™ ........36 KENWOOD Traffic Powered By INRIX ....20 TuneScan™ ..............36 Traffic & Weather Now™ .........37 Content Alerts............37 SportsFlash™ ..............38 SiriusXM SETUP ............38...
  • Page 4 Bluetooth Control Remote control Information for using Bluetooth® devices ..44 Battery Installation ...........79 Register the Bluetooth device ......45 Functions of the Remote control Buttons ..79 Bluetooth Setup ............47 Connection/Installation Playing the Bluetooth Audio Device ....48 Using the Hands-Free Unit ........50 Before Installation ............82 Hands-Free Setup .............55 Installing the unit .............85...
  • Page 5: Before Use

    See System Setup For best results while pairing with your (P.65). KENWOOD receiver, please be sure to close any • The Radio Broadcast Data System feature unused applications. won’t work in areas where the service is not supported by any broadcasting station.
  • Page 6: Basic Operations

    Basic Operations Basic Operations Functions of the Buttons on the Front Panel Number Name Motion Remote • Receives the remote control signal. Sensor • Displays the HOME screen (P.8). HOME/[ ] • Pressing for 1 second turns the power off. •...
  • Page 7: Turning On The Unit

    (P.63). ■ [Camera] Set the parameters for the camera. 1 Touch [Camera]. 2 Set each item and touch [ For details, see Camera Setup (P.56). [OEM SETUP] ■ This function requires a commercial adaptor. Consult your KENWOOD dealer for details.
  • Page 8 Basic Operations [Clock Adjust] ■ [DEMO] ■ Set the demonstration mode. Default is “ON”. If you select [Manual] for Clock, adjust the date and time manually. (P.7) Touch [Finish]. NOTE • Please set the date and time. If they are not set, some functions may not work.
  • Page 9: Adjusting The Volume

    Basic Operations Adjusting the volume HOME screen descriptions You can adjust the volume (0 to 40). Most functions can be performed from the HOME screen. Turn the knob clockwise to increase, and counter-clockwise to decrease. • Widget (P.14) Touch screen operations •...
  • Page 10: Popup Menu

    Basic Operations Popup menu Turn off the screen Select [Display OFF] on the popup menu. Press the [MENU]/[ATT] button. h Popup menu appears. Touch to display the popup menu. NOTE • Touch the display to turn on the screen. • To display the clock while the screen is off, it is necessary to set "OSD Clock"...
  • Page 11 Basic Operations Select the playback source • For sources and information displayed when an iDatalink is connected, see OEM Features Operation (P.60). Press the [HOME]/[ ] button. *1 When connecting as Apple CarPlay or Android Auto, it works as a phone provided in Apple CarPlay or h HOME screen appears.
  • Page 12: Source Control Screen Descriptions

    Basic Operations Customize Short-cut source icons Source control screen descriptions You can arrange the positions of the source icons as you like. There are some functions which can be The 4 items placed in bottom line will appear performed from most screens. on the bottom bar in various screens, as the short-cut playback source icons.
  • Page 13: List Screen

    Basic Operations * For right hand drive vehicles, the left and right etc. drawers are swapped. For how to set up the driving position, see User Interface Setup Keys with various functions are displayed here. (P.64). • : Plays all tracks in the folder containing the current track.
  • Page 14: Alert Message

    Basic Operations Alert Message Display of the received Alert Message This function is to receive alert messages. First, You can read the received alert message you need to turn on the “Emergency Alerts” on afterward. the HD Radio source control screen. (P.28) When an Alert Message comes Touch [ ] on the right side of the HD...
  • Page 15: Widget

    *1 You can receive INRIX weather forecast by connecting your iPhone or Android smartphone • [ ] (USB/HDMI/AV-IN/Wireless Mirroring source in which the “KENWOOD Traffic Powered By INRIX” only): application is installed. Displays the source control screen. *2 Displayable widgets vary depending on the type of •...
  • Page 16: Importing Image Files

    (P.64). Drag the drive widget to right or left. Preparation Weather Widget • Install the latest version of the “KENWOOD Portal You can display the weather forecast of the APP” application on your iPhone or Android present location.
  • Page 17: Apps

    APPS APPS Wireless Mirroring Operation Apple CarPlay Operation You can display the same screen of the Apple CarPlay is a smarter, safer way to use Android smartphone on the monitor of the your iPhone in the car. Apple CarPlay takes unit using the Wireless Mirroring function of the things you want to do with iPhone while the Android smartphone.
  • Page 18 APPS Ñ Select an Apple CarPlay device Wireless connection You can select the iPhone registered in [Device If two or more iPhone compatible with Apple List] and use it as the Apple CarPlay device. CarPlay have been registered, select the See Register the Bluetooth device (P.45).
  • Page 19: Android Auto Operation

    APPS Ñ Use Siri Android Auto™ Operation You can activate Siri. Android Auto enables you to use the functions Press the [VOICE] button. of your Android smartphone convenient for driving. You can easily access route guidance, make calls, listen to music, and access convenient functions on the Android smartphone while driving.
  • Page 20 APPS Ñ Ñ Connect Android smartphone Select an Android smartphone If two or more Android smartphones Wired connection have been registered, select the Android smartphone to be used as the Android Auto Connect an Android smartphone via the source. See Switch the connected device USB terminal.
  • Page 21: Kenwood Traffic Powered By Inrix

    Powered By INRIX” application is installed to this unit. Preparation Start speaking. • Install the latest version of the KENWOOD Traffic Powered By INRIX application on your iPhone or NOTE Android smartphone. • When you press and hold the [VOICE] button –...
  • Page 22: Usb

    Connecting a USB device USB Basic Operation Most functions can be controlled from the Connect the USB device with the USB source control screen and playback screen. cable. (P.92) NOTE • Set the remote controller mode switch to AUD mode before starting operation, see Switch the operation mode (P.79).
  • Page 23 Video screen • [DH] : Plays or pauses. • [ ] : Displays the Graphic Equalizer screen. (P.69) • [ ] : Repeats the current track/folder. Each time you touch the key, repeat modes are switched in the following sequence: File repeat ( ), Folder repeat ( ), Repeat...
  • Page 24: Search Operation

    Ñ Search Operation Link search (Audio file only) You can search for a file of the same artist/ You can search music or video files by the album/genre as that in the current track. following operations. Touch [Link Search]. Touch [1]. Touch the desired tag type.
  • Page 25: Ipod/Iphone

    Bluetooth device and do the profile setting • Latest compatible list of iPod/iPhone. For details, for the connection beforehand. See Register see www.kenwood.com/cs/ce/ipod/. the Bluetooth device (P.45) and Switch the connected device (P.46). • By connecting your iPod/iPhone to this unit with the iPod connection cable KCA-iP103 (optional •...
  • Page 26: Ipod/Iphone Basic Operation

    iPod/iPhone iPod/iPhone Basic Operation Content list • Touch the left side of the screen to display the Content list. Touch again to close the list. NOTE • Displays the playing list. When you touch a • Set the remote controller mode switch to AUD track/file name on the list, playback will start.
  • Page 27: Search Operation

    iPod/iPhone Ñ Search Operation Category search You can search for a file by selecting a You can search music files by the following category. operations. Touch [Category List]. Touch [1]. Touch the desired category. Touch [S]. Select a list type. h The list corresponding to your selection appears.
  • Page 28: Hd Radio™ Tuner

    HD Radio™ Tuner HD Radio™ Tuner HD Radio Tuner Basic Operation keys Operation • [E] [F] : Tunes in a station. The method of switching frequencies can be changed (see Seek mode). Most functions can be controlled from the • [CHS] [CHR] : Selects a channel. source control screen.
  • Page 29 HD Radio™ Tuner • [Emergency Alerts] : Turn on or off the alert message. See Alert Message (P.13). • [Alert Message Log] : Displays the alert message received. See Alert Message (P.13). Picture The picture data or station Logo data is displayed if available from current content.
  • Page 30: Receive Mode

    HD Radio™ Tuner Receive Mode Touch [ ] on the right side of the screen. Touch [AME]. You can set the radio broadcasts receive mode. Touch [ ] on the right side of the screen. Touch [RCV]. Touch [Yes]. Select a receive mode. h Auto memory starts.
  • Page 31 HD Radio™ Tuner Ñ Direct search Select the desired content from the list. You can tune in by entering the desired frequency or channel number. Touch [ ] on the right side of the screen. Touch [10key Direct]. NOTE • Touch [Info Change] in the channel list. Select the sequence of the list (Song title, artist name, album name).
  • Page 32: Bookmark

    HD Radio™ Tuner Bookmark Stores tag information (title, artist, album, URL, and description) about the song you are listening to now. Detailed information and QR codes can be displayed according to the stored tag information. Ñ Bookmark registration Delete] ■ Deletes the bookmarks being displayed.
  • Page 33: Siriusxm

    SiriusXM® SiriusXM® Control screen SiriusXM® Basic Operation Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio.
  • Page 34 SiriusXM® Logo: Channel logo SmartFavorite music channels on the current preset band. See TuneScan™ (P.36). Touching [ ] allows you to switch between • [TuneMix]* : When turned ON, shuffles the Content A, Content B and Content C. preset channels on P1-P6 to play a blend Content A: Artist Name, Song Title of songs from your favorite channels.
  • Page 35: Storing Channels In Preset Memory

    SiriusXM® Storing Channels in Preset Direct search Memory You can tune in a channel directly. You can store the current channel in memory. Touch [ ] on the right side of the screen. Touch [Direct Channel]. Tune in the channel you wish to store in the memory.
  • Page 36: Category/Channel Search

    SiriusXM® Category/Channel search Replay You can specify the desired category and You can replay the last 60 minutes of the select a channel. program from the current channel. Touch [1]. Touch [Replay] on the function panel. Select a category. ■ [E] [F] Press to skip to the previous/next track.
  • Page 37: Tunemix

    SiriusXM® TuneScan™ To return to live music/content Touch [ ] on the right side of the screen. TuneScan™ is a feature that plays samples from the starts of multiple buffered songs Touch [Live]. from each of the SmartFavorites channels that predominantly play music selections.
  • Page 38: Traffic & Weather Now

    SiriusXM® Traffic & Weather Now™ Content Alerts Traffic & Weather Now™ allows you to access When a broadcast program related to the the latest report whenever you want to hear registered artist, song or team starts, an Alert it. First select your city in the set up menu. See Content List screen appears to allow you to Select a City for Traffic &...
  • Page 39: Sportsflash

    SiriusXM® SportsFlash™ SiriusXM SETUP SportsFlash™ will notify you when a big play Touch [ ] on the right side of the screen. happens during a game with one of your Touch [SETUP]. favorite sports teams. Choose to tune in and hear the play unfold like it was live.
  • Page 40 SiriusXM® Ñ Ñ Parental code Parental Control You can set a SiriusXM parental code for Parental Control is a feature that provides the Parental Control. user with the ability to prevent unauthorized access to mature content and user selected Touch [Parental Code] on the SiriusXM channels.
  • Page 41 SiriusXM® Touch each channel in the list and set to NOTE ON or OFF. • Touch [All-Channels] to display all channels. • To delete the parental lock channel setting, touch [Disable All] and then touch [YES] on the confirmation screen. Touch each channel on the list and set to ON or OFF.
  • Page 42 SiriusXM® Touch each content list item you want to To select a Team check or uncheck. Get alerted when your favorite sports team is playing on another SiriusXM channel with GameAlert™ Touch [My Games]. NOTE • You can select (þ) up to 60 artists or songs. Touch the desired league in the list.
  • Page 43 SiriusXM® Ñ SportsFlash™ setup Touch [ ] twice. Activating SportsFlash Touch [SportsFlash] on the SiriusXM SETUP screen. h SportsFlash is turned on or off. Default is “ON”. Selecting SportsFlash Beep Touch [SportsFlash Beep] on the SiriusXM SETUP screen. ■ [Edit] h SportsFlash Beep is turned on or off.
  • Page 44 SiriusXM® Ñ Selecting Featured Bands Touch [Done]. Update Messages You can set whether to be notified when the featured seasonal theme is updated. Touch [Featured Bands Update Messages] on the SiriusXM SETUP screen. Featured Bands Update Messages is turned on or off. Ñ...
  • Page 45: Bluetooth Control

    Bluetooth Control Bluetooth Control Ñ Using the Bluetooth function allows you to use About the smartphone/cell- various functions such as listening to the audio phone and Bluetooth audio file and making/receiving a call. player Information for using This unit conforms to the following Bluetooth specifications: Bluetooth®...
  • Page 46: Register The Bluetooth Device

    Bluetooth Control Register the Bluetooth device [Android Auto] ■ To connect as Android Auto source. It is necessary to register the Bluetooth audio Touch [ player or smartphone/cell-phone in this unit h Bluetooth pairing waiting dialog before using the Bluetooth function. appears.
  • Page 47 Bluetooth Control To switch the connected device to a Touch [Yes]. Bluetooth device When data transmission and connection have completed, the Bluetooth connection Touch [Bluetooth] on the Device List icon appears on the screen. screen. NOTE h Bluetooth device list appears. •...
  • Page 48: Bluetooth Setup

    Bluetooth Control Touch the device name to check. Touch [Bluetooth] and set to [ON]. See the following section for each setting. • Change the PIN Code (P.47) • Change the device name (P.47) • Change the settings for Hands-Free function, see Hands-Free Setup (P.55). NOTE •...
  • Page 49: Playing The Bluetooth Audio Device

    Bluetooth basic operation (P.47) KENWOOD Music Mix Control screen Bluetooth audio devices can be switched easily to play music. See KENWOOD Music Mix (P.49). * These items appear only when the audio player which supports AVRCP profile is connected. NOTE •...
  • Page 50 Touch the desired file or folder. • : Device used normally. When you touch a folder its contents are • : Device used for KENWOOD Music Mix displayed. Touch [ ] (White/dark blue background) Touch the desired item in the content list.
  • Page 51: Using The Hands-Free Unit

    Bluetooth Control Using the Hands-Free Unit Select a dialing method. You can use the telephone function by connecting the Bluetooth telephone to this unit. NOTE • While Apple CarPlay or Android Auto is connected, the Bluetooth Hands-Free function and two Bluetooth devices connections cannot be used.
  • Page 52 Bluetooth Control Call using call records Select the phone number from the list. Touch [ Select the phone number from the list. NOTE • You can sort the phone numbers in the list by last name or first name. For details, see Hands-Free Setup (P.55).
  • Page 53 Bluetooth Control Ñ Receive a call Call by entering a phone number Touch [ Touch [ ] to answer a phone call or ] to reject an incoming call. Enter a phone number with number keys. NOTE Touch [ • When shifting the gear to the reverse (R) position and monitoring the picture from the rear view Ñ...
  • Page 54 Bluetooth Control Ñ Operations during a call ● Call-waiting When you receive a new call while talking on the phone, you can answer the newly received call by touching [ ]. The current call is put on hold. Each time you touch [ ], the caller will change to the other one.
  • Page 55 Bluetooth Control Ñ Ñ Phone number preset Phonebook transfer You can register frequently used phone You can transfer phonebook data from your numbers in this unit. Bluetooth smartphone using PBAP. Touch [ Touch [ Touch [Edit]. Touch [ h Phonebook data transfer starts. NOTE Select where to preset.
  • Page 56: Hands-Free Setup

    Bluetooth Control Touch [Delete]. [Auto Response]* ■ Set the automatic response time to pick-up h Confirmation message appears. an incoming call. Touch [Yes]. [OFF] (Default): Turns off the Automatic response function. Hands-Free Setup [1/5/10/15/20/25/30]: Sets the ringing time (second). You can make various settings for the Hands- [Auto Pairing] ■...
  • Page 57: Other External Components

    Other External Components Other External Components View Camera Camera off Touch to exit the camera screen. Switching the Guideline * NOTE Touching each time turns on or off the • To connect a camera, see Connecting the guideline. camera (P.94). •...
  • Page 58 Other External Components Ñ To set up the camera [Rear Camera Message] * ■ [Always display] (Default): Always displays assignment settings the caution message on the rear camera interruption screen. Touch [Camera Assignment Settings] in [Clear after 5 seconds]: Displays the the Camera setting menu.
  • Page 59: Use Dashboard Camera

    Other External Components Adjusting the position of the selected *1 Except the [REAR VIEW CAMERA] setting mark. screen. *2 The [REAR VIEW CAMERA] setting screen only. *3 The [REAR VIEW CAMERA] and [FRONT VIEW CAMERA / DASH CAM] setting screens only. *4 The [FRONT VIEW CAMERA / DASH CAM] and [3rd VIEW CAMERA] setting screens only.
  • Page 60: External Audio/Video Players (Av-In)

    Other External Components Ñ Display the dashboard camera External audio/video players screen (AV-IN) Press the [MENU]/[ATT] button. Connect an external component to the AV h Popup menu appears. Audio input and the Video input terminal. (P.91) Touch [Camera]. Select [AV-IN] as the source. (P.10) Turn on the connected component and start playing the source.
  • Page 61: Oem Features Operation

    Other External Components OEM Features Operation NOTE • Displayable screens, key names, and screen This unit can display vehicle information when names vary depending on the type of the connected to the bus system of the vehicle connected iDatalink and the model of the vehicle. using an iDatalink (commercially available).
  • Page 62: Setup

    Setup Setup Press the [HOME]/[ ] button. ■ [Backlight]/[Contrast]/[Black]/ [Brightness]/[Color]/[Tint] Touch [ ]. Adjust each setting. Touch [SETUP]. ■ [Aspect] Select a screen mode. [Full]: Changes the aspect ratio of video and displays video fully on the screen. [Normal]: Displays video at the ratio of 4:3. [Auto]: USB device: Displays video fully (vertically or horizontally) with no ratio change.
  • Page 63 Setup • If you select HDMI as the main source, files [Device Name] ■ with sampling rates higher than 96 kHz in If you select [ON] for [Bluetooth], you can USB selected as the AV output source are change the Bluetooth device name. skipped.
  • Page 64: Display & Button Setup

    Setup Ñ Display & Button Setup Customizing the button color You can set the button illumination color. Press the [HOME]/[ ] button. Touch [Button Illumination Color] in the Display & Button setting menu. Touch [ ]. Touch the desired color. Touch [SETUP].
  • Page 65: User Interface Setup

    “Variable”, this option is fixed to OFF. Touch [ To register an original image The album art currently being displayed is With “KENWOOD Portal APP” application used as a wallpaper. installed on your iPhone or Android Select a wallpaper color in advance.
  • Page 66: System Setup

    Setup System Setup ■ [Beep] Turn the key touch tone on or off. Default is “ON”. You can setup system parameters. [Parking Assist Display] ■ Press the [HOME]/[ ] button. When the iDatalink (commercially available) Touch [ ]. is connected, you can display information about obstacles around the car.
  • Page 67 Setup Ñ Software Information You can confirm the software version of this unit. Touch [Software Information] in the System setting menu. Confirm the software version. NOTE • For how to update the software, see the relevant update procedure manual which comes with the software.
  • Page 68: Controlling Audio

    Controlling Audio Controlling Audio You can adjust various settings such as audio 3-way speaker system setup balance or subwoofer level. (DMX1057XR) Press the [HOME]/[ ] button. Select the appropriate crossover network Touch [ ]. mode for the speaker system used (2-way or 3-way speaker system).
  • Page 69: Speaker / X'over Setup

    Controlling Audio Touch the speaker (1) you wish to adjust NOTE and set each parameter (2) as follows. • When the 3-way speaker system is selected, the following functions are disabled. – Front focus of Listening Position / DTA – Fader for Controlling General Audio –...
  • Page 70: Equalizer Control

    Controlling Audio Equalizer Control When Speaker network is set to 3-way: You can adjust equalizer by selecting the optimized setting for each category. Press the [HOME]/[ ] button. Touch [ ]. Touch [Audio]. h Audio screen appears. ■ [Speaker] Touch [EQ / SW Level]. You can select a speaker type and its size to get the best sound effects.
  • Page 71: Listening Position / Dta

    Controlling Audio Ñ Save the EQ curve Listening Position / DTA Adjust the EQ curve. Listening Position / DTA allows you to improve the sound field depending on the position of Touch [Memory]. the seat you sit. Listening Position / DTA allows you to set Select where to save.
  • Page 72 Controlling Audio Ñ Front Focus Position DTA control You can fine-adjust your listening position. You can focus the imaginary sound image on the front of the selected seat. Touch [Adjust]. Touch [Front Focus] in the Position / DTA Touch [Delay]. screen.
  • Page 73: Fader / Balance / Zone Control

    Controlling Audio Fader / Balance / Zone Control [Size of the Virtual Sound Field] ■ Adjust the size of sound image to meet your taste. If the sound image is shifted from the Press the [HOME]/[ ] button. front, move it back by [Sound Image LR (Front)] or [Sound Image LR (Rear)].
  • Page 74 Controlling Audio Ñ Zone Control NOTE You can select different sources for front and • When the rear source is switched, the audio source that is output at the AV OUTPUT terminal rear positions in the vehicle. is also switched to the same source. Touch [Dual Zone] on the FAD / BAL / •...
  • Page 75: Volume Offset

    Controlling Audio Volume Offset Set each parameter as follows. Finely adjust the volume of the current source to minimize the difference in volume between different sources. Press the [HOME]/[ ] button. Touch [ ]. Touch [Audio]. h Audio screen appears. [Bass Boost] ■...
  • Page 76: Parametric Equalizer

    Controlling Audio Parametric Equalizer About Adjustments If there are unpleasant peaks, you can slide the (DMX1057XR) peaking filter to the left or right and search the frequencies by ear. Studio engineers use In addition to the conventional Graphic this method to make adjustments quickly and Equalizer, this unit has a parametric equalizer, efficiently.
  • Page 77 Controlling Audio ● High-Pass Filter ● Peaking Filter Passes signals with frequencies higher than The frequencies in the vicinity of a certain a certain frequency (fc: cutoff frequency) frequency (f0: center frequency) are and attenuates signals with frequencies boosted or attenuated. Use this in the lower than the cutoff frequency.
  • Page 78 Controlling Audio Ñ Adjust the Parametric Equalizer EQ point (blue/yellow): EQ points that are not currently being adjusted. Preparation Curve (orange): EQ curve of the speaker currently being adjusted. • Correct the value in “Listening Position” and “Front Focus” before adjusting the parametric equalizer. Curve (blue): Overall EQ curve.
  • Page 79: Audio Setup Memory

    Controlling Audio Audio Setup memory When you have finished adjustments, save the results as a preset, and check the effects by switching presets or turning Audio Control settings can be memorized. the Parametric EQ [ON] and [OFF]. The memorized settings can be recalled at any time.
  • Page 80: Remote Control

    Remote control Remote control This unit can be operated using the remote Functions of the Remote control KNA-RCDV331 (optional accessory). control Buttons # CAUTION Ñ Switch the operation mode • Risk of fire or explosion if the battery is replaced by an incorrect type. Ensure to The functions operated from the remote replace only with the same type.
  • Page 81 Remote control Ñ Ñ Direct search mode Basic Operation Using the remote control, you can jump directly to the desired channel by entering the number corresponding to the content. NOTE • This operation cannot be performed for the USB device and iPod. Press the [#BS] button several times until the desired content appears.
  • Page 82 Remote control Key Name Mode Function switch Selects the track or file to be played. For the HD Radio, and SiriusXM sources, switches to broadcast stations received by the unit. Numeric Allows you to enter the number to search in the direct search mode. For details on the direct search mode, see Direct search mode (P.80).
  • Page 83: Connection/Installation

    Connection/Installation Connection/Installation This section is for the professional installer. • If the power is not turned ON (“There is an error in the speaker wiring. Please check the For safety’s sake, leave wiring and mounting to connections. ” is displayed), the speaker wire professionals.
  • Page 84 Connection/Installation Ñ Supplied accessories for installation Cooling fan • Do not press hard on the panel surface when (1 m) installing the unit to the vehicle. Otherwise scars, damage, or failure may result. • Reception may drop if there are metal objects (3 m) near the Bluetooth/Wi-Fi antenna.
  • Page 85 Connection/Installation (Ø3 x 6 mm) (Black) Ñ Installation procedure 1) To prevent a short circuit, remove the key from the ignition and disconnect the ¤ terminal of the battery. 2) Remove the vehicle parts for installing the unit and connecting wires to terminal. 3) Make the proper input and output wire connections for each unit.
  • Page 86: Installing The Unit

    Connection/Installation Installing the unit Ñ Confirm the installing position of the display unit ● Vehicles cannot be installed It may be possible to install if it can avoid the following by adjustment for slider position and display height. Lever operations are interfered A hazard switch is hidden from a The display unit hits a panel on the such as shift lever, wiper lever,...
  • Page 87 Connection/Installation Ñ Positioning the slider in Install the bracket for forward position (accessory 0) each side so that its forward projections are aligned with the slots on the main unit. Remove the four screws from the bottom of the main unit. Projection Screw Projection...
  • Page 88 Connection/Installation Ñ Ñ Adjusting the display height GPS antenna GPS antenna is installed inside of the car. It Remove the four flat head screws from should be installed as horizontally as possible both sides. to allow easy reception of the GPS satellite signals.
  • Page 89 Connection/Installation Ñ Ñ Microphone unit Installing the main unit 1) Check the installation position of the NOTE microphone (accessory 3). • Determine the slider position before installing the 2) Clean the installation surface. main unit. (P.86) The slider position cannot be 3) Remove the separator of the microphone changed after installing to the vehicle.
  • Page 90 Connection/Installation Install the display unit (accessory 8) to Attach the protective cover (accessory =) the main unit. to coupling part, and then fix it with two binding head screws (accessory ~). Main unit NOTE • If the display unit hits a panel on the vehicle, NOTE adjust the display height by referring to Adjusting the display height (P.87).
  • Page 91 Connection/Installation Ñ Connecting wires to terminals Fuse (15A) Speaker impedance: 4-8 Ω White To front left speaker White/Black Gray To front right speaker Gray/Black Green To rear left speaker Green/Black Connect to the vehicle’s Accessory 1 parking brake detection switch harness.
  • Page 92 Connection/Installation Ñ Ñ 3-way speaker system setup Connecting the system and external components ● DMX1057XR Subwoofer Preout Mid Range Preout Tweeter Preout When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit. Preout RCA Cable (Sold separately)
  • Page 93 Connection/Installation Ñ Connecting a USB device HDMI input Use HDMI cable KCA-HD100 (optional Accessory 2 (1 m) accessory). When you connect the cable to HDMI terminal, USB device remove the fixture. After connecting the cable, put the fixture again. Fixture USB terminal HDMI connector iDatalink connector...
  • Page 94 Connection/Installation Ñ Ñ Securing the USB extension Connecting an Android cable smartphone Secure the USB extension cable with insulating Android smartphone tape or the like so that its connectors are not USB cable disconnected. Accessory 2 (1 m) Ñ Connecting an iPod/iPhone USB terminal KCA-iP103 (0.8 m) Lightning Digital AV...
  • Page 95 Connection/Installation Ñ Connecting the camera For HD video, an HD camera is also used as Rear view camera. Left side view camera and For HD video, an HD camera is also used as Right side view camera Front view camera. Front view camera [4] [6] Video input...
  • Page 96: Troubleshooting

    † Turn the power off and on again. If the “Error 07−67” The dual zone function is disabled. message does not disappear, contact your nearest † Set the dual zone function to on. See Zone Control KENWOOD dealer. (P.73). No Device (USB device) • Cannot set up the equalizer.
  • Page 97 USB to use Apple CarPlay. † Turn the power off and on again. If the “Starting tuner failed. ” message does not disappear, contact your nearest KENWOOD dealer. Ñ SiriusXM Check Tuner A SiriusXM tuner is not connected to this unit.
  • Page 98: Appendix

    Appendix Appendix Playable Media and Files You can play various kinds of media and files on this unit. Ñ About files The following audio and video files are supported. ■ Playable Audio files Format Bit rate Sampling frequency Bit count AAC-LC (.m4a) MPEG-2/MPEG-4 AAC LC 8 –...
  • Page 99 Appendix ■ Limitation on structure of file and folder USB device Maximum number of folder layers Maximum number of files (per folder) Maximum number of folders (per folder) 9999 Maximum number of folders (per device) Unlimited • You can enter a folder name and file name with 255 or fewer single-byte characters. •...
  • Page 100: Specifications

    Appendix Specifications ■ Wireless Mirroring Section Mode ■ Monitor section : Sink Copyright protection Picture Size : HDCP2.2 : 10.1 inches (diagonal) wide : 223.7 mm (W) × 125.8 mm (H) Touch Control 8-13/16 × 4-15/16 inch : UIBC Display System ■...
  • Page 101 Appendix ■ HDMI section ■ Digital FM tuner section HDMI Frequency Range (step) : Type-A : 87.9 MHz – 107.9 MHz (200 kHz) Input Resolution Frequency Response (± 3.0 dB) • VGA (640x480p @59.94Hz/60Hz) : 20 Hz – 20 kHz •...
  • Page 102 : 22 W × 4 Output frequency band : 20 – 88,000 Hz Preout Level (V) DMX1057XR : 5 V/10 kΩ DMX1037S : 4 V/10 kΩ Preout Impedance : ≤ 300 Ω Speaker Impedance : 4 – 8 Ω ■ General...
  • Page 103: About This Unit

    Appendix Ñ About this Unit EULA ■ Software License Agreement Ñ Important Notice on Software JVCKENWOOD Corporation (hereinafter called “Licensor”) holds either the copyright to the embedded software or the right to sublicense it. This agreement ■ Software License on This Product establishes the conditions under which the customer The software embedded in this product comprises a uses this “Licensed Software.
  • Page 104 Appendix Article 4 (Rights to Licensed Software) Article 11 (Export Control) All rights to Licensed Software and the associated 1. Licensed Software and the associated literature or literature, including copyrights, shall reside with the like may not be exported to places outside the Licensor or Country (including transmission outside the Country the original right holder who has granted the Right...
  • Page 105 Appendix ■ Copyrights • Wi-Fi® is a registered trademark of Wi-Fi Alliance®. • The Wi-Fi CERTIFIED™ Logo is a certification mark of • The Bluetooth® word mark and logos are registered Wi-Fi Alliance®. trademarks owned by Bluetooth SIG, Inc. and any use •...
  • Page 106 Appendix LICENSED TO PROVIDE VC-1 VIDEO. NO LICENSE IS EXPRESS OR IMPLIED WARRANTIES, INCLUDING, GRANTED OR SHALL BE IMPLIED FOR ANY OTHER BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF USE. ADDITIONAL INFORMATION MAY BE OBTAINED MERCHANTABILITY AND FITNESS FOR A PARTICULAR FROM MPEG LA, L.L.C.
  • Page 107 Products: MONITOR WITH RECEIVER – Connect the equipment into an outlet on a Model Name: DMX1057XR / DMX1037S circuit different from that to which the receiver Responsible Party: JVCKENWOOD USA is connected. CORPORATION – Consult the dealer or an experienced radio/TV 2201 East Dominguez Street, technician for help.
  • Page 108 Appendix ■ Información acerca de la eliminación ■ Informação sobre a eliminação de de equipos eléctricos y electrónicos pilhas al final de la vida útil (aplicable a los Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor países que hayan adoptado sistemas ou entidade autorizada para que a mesma seja independientes de recogida de...
  • Page 109 Hi-Res Audio logo and Hi-Res Audio Wireless logo are used under license from Japan Audio Society.
  • Page 110 Record the serial number, found on the top of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product.
  • Page 111 Important Notice on Software JVCKENWOOD Corporation, the original (English) of the license is presented. Ñ Software License on This EULA Product Ñ Software License Agreement The software embedded in this product comprises a number of independent software JVCKENWOOD Corporation (hereinafter called components, each of which is copyrighted by “Licensor”) holds either the copyright to the JVCKENWOOD Corporation or by a third party.
  • Page 112 Article 3 (Terms of License) Article 8 (Cancellation of the Agreement) Licensor reserves the right to cancel this 1. In assigning this product, User may not retain agreement forthwith and claim compensation the original copy of the embedded Licensed from User for the damages caused by such Software (including associated literature, cancellation when User: updates and upgrades) and any duplicates...
  • Page 113 • If you experience problems during installation, consult your KENWOOD dealer. Ñ Precautions on using this unit • When you purchase optional accessories, check with your KENWOOD dealer to make sure that they work with your model and in your area.
  • Page 114: Before Use

    Ñ For best results while pairing with your Protecting the monitor KENWOOD receiver, please be sure to close any • To protect the monitor from damage, do not unused applications. operate the monitor using a ball point pen or similar tool with a sharp tip.
  • Page 115: Basic Operations

    Basic Operations Basic Operations Functions of the Buttons on the Front Panel Number Name Motion Remote • Receives the remote control signal. Sensor • Displays the HOME screen (P.10). HOME/[ ] • Pressing for 1 second turns the power off. •...
  • Page 116: Turning On The Unit

    Basic Operations Turning on the Unit ● To turn off the unit: Press the [HOME]/[ ] button. Press the [HOME]/[ ] button for 1 second. NOTE • If it is your first time to turn the unit on after installation, it will be necessary to perform Initial SETUP (P.8).
  • Page 117: Initial Settings

    For details, see Camera Setup (P.56) in time. the Instruction Manual. [OEM SETUP] ■ Set each item as follows. This function requires a commercial adaptor. Consult your KENWOOD dealer for details. ■ [DEMO] Set the demonstration mode. Default is “ON”. Touch [Finish]. ■ [Language] Select the language used for the control screen and setting items.
  • Page 118: Adjusting The Volume

    Basic Operations Calendar/clock settings ● Adjust the date and time manually Touch [Clock Adjust] in the System Press the [HOME]/[ ] button. setting menu. Touch [ Adjust the date, then adjust the time. Touch [SETUP]. h SETUP Menu screen appears. Touch [System].
  • Page 119: Touch Screen Operations

    Basic Operations Touch screen operations HOME screen descriptions To perform operations on the screen, you need Most functions can be performed from the to touch, touch and hold, flick or swipe to HOME screen. select an item, display a setting menu screen or change pages.
  • Page 120: Popup Menu

    Basic Operations Widget • Close the popup menu. • Displays the Device List screen. Press the [HOME]/[ ] button. h HOME screen appears. • Short-cut source icons: The source changes to the one you have set with a You can change the widget or customize short-cut.
  • Page 121 Basic Operations Select the playback source Put the unit in standby Press the [HOME]/[ ] button. Press the [HOME]/[ ] button. h HOME screen appears. h HOME screen appears. Touch [ Touch [ From the screen, you can select the following sources and functions.
  • Page 122: Source Control Screen Descriptions

    Basic Operations Source control screen List screen descriptions There are some common function keys in the list screens of most sources. There are some functions which can be performed from most screens. Display the list screen Touch [1]. h The list screen appears. Displays the source selection screen.
  • Page 123: Usb/Ipod

    USB/iPod USB/iPod Connecting a USB device Connect iPod/iPhone Connect the USB device with the USB Preparation cable. (P.32) • With an iPhone compatible with Apple CarPlay, turn off Apple CarPlay by operating the iPhone at functional setup before connecting iPhone. For details of the setup method, contact the manufacturer of the terminal.
  • Page 124: Usb/Ipod Basic Operation

    USB/iPod USB/iPod Basic Operation Press the [HOME]/[ ] button. Touch [ Touch [USB] or [iPod]. (P.12) Control screen CODEC When a high-resolution source is played, its format information is displayed. Operation keys • [1] : Searches track/file. • [E] [F] : Searches the previous/next track/ file.
  • Page 125: Hd Radio™ Tuner

    HD Radio™ Tuner HD Radio™ Tuner HD Radio Tuner Basic • [ ] : Stores the information about the song being received. Operation • [Emergency Alerts] : Turn on or off the alert message. To listen to the HD Radio source, touch [HD Radio] icon on the source selection screen.
  • Page 126: Memory Operation

    HD Radio™ Tuner Memory Operation Ñ Auto memory You can store stations with good reception in the memory automatically. Touch desired band key. Touch [ ] on the right side of the screen. Touch [AME]. Touch [Yes]. h Auto memory starts. Ñ...
  • Page 127: Bluetooth Control

    Bluetooth Control Bluetooth Control Operate your smartphone/cell-phone Register the Bluetooth device according to the displayed messages. It is necessary to register the Bluetooth audio ● Confirm the request both on the player or smartphone/cell-phone in this unit smartphone/cell-phone. before using the Bluetooth function. Press the [HOME]/[ ] button.
  • Page 128: Using The Hands-Free Unit

    Bluetooth Control Using the Hands-Free Unit • [ ]: Call using the preset number • [ ]: Call by entering a phone number You can use the telephone function by connecting the Bluetooth telephone to this ● Select the smartphone/cell-phone to use unit.
  • Page 129 Bluetooth Control Select the phone number from the list. NOTE • When shifting the gear to the reverse (R) position and monitoring the picture from the rear view camera, this screen does not appear even if a call comes in. •...
  • Page 130: Controlling Audio

    Controlling Audio Controlling Audio Ñ You can adjust various settings such as audio Equalizer Control balance or subwoofer level. You can adjust equalizer by selecting the optimized setting for each category. Press the [HOME]/[ ] button. Touch [EQ / SW Level]. Touch [ Touch the screen and set the Graphic Touch [Audio].
  • Page 131: Connection/Installation

    Connection/Installation Connection/Installation This section is for the professional installer. connections. ” is displayed), the speaker wire may have a short-circuit or touched the chassis For safety’s sake, leave wiring and mounting to of the vehicle and the protection function may professionals.
  • Page 132 Connection/Installation Ñ Supplied accessories for • This unit has the cooling fan to decrease the internal temperature. Do not mount the unit installation in a place where the cooling fan of the unit is blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction.
  • Page 133 Connection/Installation (Ø3 x 6 mm) (Black) Ñ Installation procedure 1) To prevent a short circuit, remove the key from the ignition and disconnect the ¤ terminal of the battery. 2) Remove the vehicle parts for installing the unit and connecting wires to terminal. 3) Make the proper input and output wire connections for each unit.
  • Page 134: Installing The Unit

    Connection/Installation Installing the unit Ñ Confirm the installing position of the display unit ● Vehicles cannot be installed It may be possible to install if it can avoid the following by adjustment for slider position and display height. Lever operations are interfered A hazard switch is hidden from a The display unit hits a panel on the such as shift lever, wiper lever,...
  • Page 135 Connection/Installation Ñ Positioning the slider in Install the bracket for forward position (accessory 0) each side so that its forward projections are aligned with the slots on the main unit. Remove the four screws from the bottom of the main unit. Screw Projection Projection...
  • Page 136 Connection/Installation Ñ Ñ Adjusting the display height GPS antenna GPS antenna is installed inside of the car. It Remove the four flat head screws from should be installed as horizontally as possible both sides. to allow easy reception of the GPS satellite signals.
  • Page 137 Connection/Installation Ñ Ñ Microphone unit Installing the main unit 1) Check the installation position of the NOTE microphone (accessory 3). • Determine the slider position before installing the 2) Clean the installation surface. main unit. (P.26) The slider position cannot be 3) Remove the separator of the microphone changed after installing to the vehicle.
  • Page 138 Connection/Installation Install the display unit (accessory 8) to Attach the protective cover (accessory =) the main unit. to coupling part, and then fix it with two binding head screws (accessory ~). Main unit NOTE • If the display unit hits a panel on the vehicle, NOTE adjust the display height by referring to Adjusting the display height (P.27).
  • Page 139 Connection/Installation Ñ Connecting wires to terminals Fuse (15A) Speaker impedance: 4-8 Ω White To front left speaker White/Black Gray To front right speaker Gray/Black Green To rear left speaker Green/Black Connect to the vehicle’s Accessory 1 parking brake detection switch harness.
  • Page 140 Connection/Installation Ñ Ñ 3-way speaker system setup Connecting the system and external components ● DMX1057XR Subwoofer Preout Mid Range Preout Tweeter Preout When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit. Preout RCA Cable (Sold separately)
  • Page 141 Connection/Installation Ñ Securing the USB extension HDMI input cable Use HDMI cable KCA-HD100 (optional accessory). Secure the USB extension cable with insulating When you connect the cable to HDMI terminal, tape or the like so that its connectors are not remove the fixture.
  • Page 142 Connection/Installation Ñ Ñ Connecting an iPod/iPhone Connecting an Android smartphone Lightning Digital AV KCA-iP103 (0.8 m) Adapter Android smartphone USB cable iPod/iPhone KCA-HD100 (1.8 m) KCA-iP103 (0.8 m) Accessory 2 (1 m) Accessory 2 (1 m) USB terminal USB terminal USB maximum power supply current : iPhone (with Apple CarPlay) DC 5 V = 1.5 A...
  • Page 143 Connection/Installation Ñ Ñ Connecting the camera To set up the camera assignment settings Left side view camera and Right side view camera Press the [HOME]/[ ] button. Front view camera [4] [6] Touch [ Touch [SETUP]. Video input h SETUP Menu screen appears. (Yellow) Touch [Camera].
  • Page 144: Appendix

    Appendix Appendix ■ Copyrights • The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under Note for specifications license. Other trademarks and trade names are those of their respective owners.
  • Page 145 Appendix • Wi-Fi® is a registered trademark of Wi-Fi Alliance®. AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE VC-1 VIDEO. NO LICENSE IS • The Wi-Fi CERTIFIED™ Logo is a certification mark of GRANTED OR SHALL BE IMPLIED FOR ANY OTHER Wi-Fi Alliance®.
  • Page 146 Appendix HOLDERS AND CONTRIBUTORS ``AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE...
  • Page 147 Hi-Res Audio logo and Hi-Res Audio Wireless logo are used under license from Japan Audio Society.

This manual is also suitable for:

Dmx1057xr

Table of Contents