Philips 24PFK5211 Service Manual page 16

EN 16 5. TPN16.1E LA
Item Item value
17 ORT_MODE
18 AGEING MODE
19 AUD_LIMITE_MODE
20 AUD_THRESHOLD_BYTE1
21 AUD_THRESHOLD_BYTE2
22 AUD_THRESHOLD_BYTE3
23 AUD_GAIN_LINEIN
24 AUD_GAIN_HDMI
25 AUD_GAIN_ATV
26 AUD_GAIN_DTV
27 AUD_GAIN_USB
28 AUD_GAIN_BT
29 TUNER_ID
30 CIPLUS QUERY
31 CIPLUS UPDATE
32 CI Key Type Selection
33 AQ_TABLE_INDEX
34 EDID UPDATE
35 LVDS SSC Ratio
36 LVDS SSC Freq
37 DDR SSC Ratio
38 DDR SSC Freq
39 Panel H.Flip
40 Panel V.Flip
41 Panel ABSwap
42 Watchdog
43 Backlight PWM freq.(Hz)
44 Backlight PWM Limit
45 VGA_TxRx_Mode
46 LVDS Driving
47 LVDS Format
48 Ziggo Aging
49 SPDIF
50 Standard PWM Gain
51 ECO PWM Gain
52 VGA port
53 Zero Detect Enable
54 Copy PQ table to TV
55 Copy AQ table to TV
56 Headphone
57 EnhancedH/88
58 Joysticker Enable
59 Ambilight Enable
60 Lounge Light Enable
61 FRC F/W Upgrade
62 Satellite Tuner Slave Address
63 912_SSC_LVDS_PERCENT
64 912_SSC_LVDS_FREQ
65 912_LVDS_DRIVING
66 912_LVDS_FORMAT
67 EXIF_FACTORY
How to Exit the Factory mode
Use one of the following methods:
• Select EXIT_FACTORY from the menu and press the "OK"
button.
Note: When the TV is switched "off" by a power interrupt, or
normal switch to "stand-by" while in the factory mode, the TV
will show up in "normal operation mode" as soon as the power
is supplied again. The error buffer will not be cleared.
5.1.4 Customer Service Mode (CSM)
Purpose
The Customer Service Mode shows error codes and
information on the TVs operation settings.The call centre can
instruct the customer (by telephone) to enter CSM in order to
identify the status of the set.This helps the call centre to
diagnose problems and failures in the TV set before making a
service call.
2016-Mar-11
Service Modes, Error Codes, and Fault Finding
Default value
24" Description
off ORT mode
off Use this for aging a new LCD panel
1 Three modes,0: off, 1: adaptive mode, 2: fixed mode
100 Limit threshold
200 Limit threshold
100 Limit threshold
0 Line-in audio gain
-10 HDMI audio gain
0 Analogue TV audio gain
0 Digital TV audio gain
0 USB audio gain
0
0 Displays and changes the Tuner ID with the left and right cursor. Not to be changed when the
tuner is replaced with the correct service part.
Press OK Shows the Validity of the CI+ key and the supplier information
Press OK Used to enter a new CI+ code into the NVM. This can only be used when no CI+ code exists in
the NVM
ProductKey CI Key Type Selection
16 Audio Quality index
Press OK Used to enter a new EDID codes into the NVM
5% LVDS SSC ratio
30KHz LVDS SSC frequency
2% DDR SSC ratio
30KHz DDR SSC frequency
off Flip panel
off Flip panel
on ABSwap panel
5sec Watchdog
150 Backlight PWM frequency
20 Backlight PWM Limit
off VGA_TxRx_Mode
2 LVDS Driving
VESA 8bit LVDS Format
Press OK Ziggo Aging
On Enable/Disable SPDIF source
100 Standard PWM Gain
100 ECO PWM Gain
on Enable/Disable VGA port
on Zero Detect Enable
Press OK Copy PQ table to TV
Press OK Copy AQ table to TV
on Enable/Disable Headphone source
on EnhancedH/88
Off Joysticker Enable
Off Ambilight Enable
Off Lounge Light Enable
Press OK FRC F/W Upgrade
0xC6 TUNER Address
0 Percent of 912_SSC_LVDS
0 912_SSC_LVDS_FREQ
0 912_LVDS_DRIVING
JEDIA 8bit The format for 912_LVDS
Press OK Exits the Factory mode
back to
div. table
The CSM is a read-only mode; therefore, modifications are not
possible in this mode.
Specifications
• Ignore "Service unfriendly modes".
• Line number for every
line (to make CSM language independent).
• Set the screen mode to full
screen (all contents on screen is visible).
• After leaving the Customer Service Mode, the original
settings are restored.
• Possibility to use "CH+" or "CH-" for channel surfing, or
enter the specific channel number on the RC.
How to Activate CSM
To activate CSM, press the following key sequence on a
standard remote control transmitter: "123654" (do not allow the
display to time out between entries while keying the sequence).