Energy Saving Tips - Frigidaire FFWC4222QS Use & Care Manual

InStALLAtIOn
Step 7:Remove the bolt on the bottom of the door by screwdriver (see chart
3)
Step 8:Remove the screw and the block ,then set them on the left side.(see
chart 3)
Step 9:Change the hinge axis
and fix the top hinge on the door,to make the door level,see chart 8.
Step 14:Check the sealing of the door,then refit the parts
Fig. 7
Step 10:Use knife to remove the parts ,see chart 5.
Placement of Wine Cooler
tEMpERAtuRE cOntROLS
The wine cooler should be placed in dry and ventilated room. The location of
the wine cooler should not be irradiated by direct sunshine. The wine cooler
should be far away from heating sources, such as: cooking stove or heating
Cool Down Period
radiator. If the wine cooler has to be placed near heating source, please adopt
For best performance, allow 4 hours for the wine cooler to cool down completely. The wine cooler will run continuously
proper heating insulation board for insulation or keep the wine cooler at least
for the first several hours.
the following minimum distances away from the heating sources:
Temperature Control for Single Zone Model
For electric stove: 3 .
Indication of Temperature in Lower Chamber
For oil or coal stove: 30 .
: Press this button once and the temperature increase 1°C.
Replacement of Door Hinge
: Press this button once and the temperature decrease 1°C.
The door hinges of this wine cooler can be interchanged between the left and
right sides.
Indication of Temperature in Upper Chamber
Installation of Handle
Indication of Temperature in Lower Chamber
1. Set the handle on the fixation shaft. Press this button once to increase temperature 1° F/C.
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature increase 1°C.
Press this button once to decrease temperature 1° F/C.
: Press this button once and the temperature decrease 1°C.
: Press this button once and the temperature decrease 1°C.
The wine cooler can be operated by adjusting the temperature control buttons (up arrow and down arrow) until
: Temperature display.
Indication of Temperature in Upper Chamber
the desired temperature is reached.
The display will flash for a few seconds before set point is locked in.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
: Press this button once and the temperature increase 1°C.
The temperature range MIN and MAX is 41° - 64°F (5° - 18° C).
Power: On/off button used to turn on/off all load.
: Press this button once and the temperature decrease 1°C.
Press Light and Power together for 2 seconds and you can convert between
fahrenheit temperature and Celsius temperature.
Temperature display
: Temperature display.
Light: This button turns the light ON and OFF.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
Notice!
Power: This buttons turns the power ON and OFF.
Power: On/off button used to turn on/off all load.
The default temperature is 10/10°C, and the temperature after power
Press both Light and Power button's at the same time
Press Light and Power together for 2 seconds and you can convert between
failure will be the temperature set before the power failure.
to change between Fahrenheit and Celsius temperatures.
fahrenheit temperature and Celsius temperature.
6
To elongate the service life of compressor, please wait for at least 5
minutes before the wine cooler is restarted after power failure.
Notice!
Chart 2
Stop
bracket
Bushing
Fig. 6
Chart 3
from the right hole to left hole(see chart 4)
.
Chart 4
- 8 -
Chart 8
- 10 -

ENERGY SAVING TIPS

•
Install the wine cooler in the
coolest part of a dry and ventilated
room, out of direct sunlight and
away from heating ducts or
registers. Do not place the wine
cooler next to heat-producing
appliances such as a range, oven
or dishwasher.
• Level the wine cooler so the door close tightly.
•
Do not over crowd the wine cooler or block cold air
vents. Doing so causes the wine cooler to run longer
and use more energy. Shelves should not be lined
with aluminum foil, wax paper or paper toweling.
Liners interfere with cold air circulation, making the
wine cooler less efficient.
• Wipe containers dry before placing them in the wine
cooler. This cuts down on moisture build-up inside
the unit.
• Organize the wine cooler to reduce door openings.
Remove as many items as needed at one time and
close the door as soon as possible.