Sharp DM-FX1 Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Copier
  5. DM-FX1
  6. Service manual
Sharp DM-FX1 Service Manual

Sharp DM-FX1 Service Manual

Digital copier fax expansion kit
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
[ 1 ] OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . 2 - 1
[ 3 ] INSTALLING PROCEDURE . . . . . . . . . . . . . . . . . 3 - 1
[ 4 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
[ 5 ] SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
[ 6 ] SOFTWARE SWITCH DESCRIPTIONS . . . . . . . . . . . 6 - 1
[ 7 ] USER PROGRAMS . . . . . . . . . . . . . . . . . . . . . . 7 - 1
[ 8 ] PRINTING . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
[ 9 ] FIRMWARE VERSION UP PROCEDURE . . . . . . . . . . 9 - 1
[10] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . .
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
DIGITAL COPIER
FAX EXPANSION KIT
(For USA/Canada)
EXPANSION 2MB: AR-MM5
MEMORY
MODEL
CONTENTS
SHARP CORPORATION
CODE: 00ZDMFX1//A1E
DM-FX1
4MB: AR-MM6
8MB: AR-MM7
10 - 1
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
DM-FX1

Advertisement

Table of Contents
loading

Related Manuals for Sharp DM-FX1

Summary of Contents for Sharp DM-FX1

  • Page 1: Table Of Contents

    DM-FX1 CODE: 00ZDMFX1//A1E DIGITAL COPIER FAX EXPANSION KIT (For USA/Canada) DM-FX1 EXPANSION 2MB: AR-MM5 MEMORY 4MB: AR-MM6 MODEL 8MB: AR-MM7 CONTENTS [ 1 ] OUTLINE ......1 - 1 [ 2 ] SPECIFICATIONS .

  • Page 2: 1 ] Outline

    2) The SPF or the RSPF must be installed to the copier which G The LINE STATUS indicator is not lit. this machine is attached to . SPF/RSPF FAX expansion kit (DM-FX1) Not lit Not lit FAX operation panel 2) Turn the power switch to the “OFF” position.

  • Page 3: 2 ] Specifications

    DM-FX1 a. Fax Mode Initial State YES(A3 to A5, 11 × 17 to Original size In the fax mode initial state, the messages similar to the following 8.5 × 5.5) detection are shown on the display panel. Depending on user program set- YES(A3 to A5, 11 ×...
  • Page 4 Relay Instructing Only from the transmission/ broadcast station machine having polling transmission Sharp relay broadcast Recall Automatic Intervals 1 to 15 minutes instruction mode recall mode Count 1 to 15 times/ transmission function when other...
  • Page 5 Confi- Confidential Sender Only Sharp (other party’s dential receiving machine having machine) (between function confidential function Sharp machines only) Confidential Up to 10 boxes may be set 6. Receiving function system Confidential 20 letters box name Recei- Default Automatic receiving...
  • Page 6 DM-FX1 Number Speed Transmission Speed dialing keys Sender registration Sender’s name 40 half-size letters, registra- dialing method + (000 to 149) + registered in user tion start key program Rapid Number of other 35 other parties Sender’s number 20 digits,...
  • Page 7 DM-FX1 9. Memory system Activity Time-specified Common to transmission Report communication record table Memory Standard table Capacity Option Up to 8MB (+2M/+4M/+8M) Confidential Confirmation Display in LCD receiving Transmission Print out confirmation table reservation Communica Communication YES (any of always...

  • Page 8: 3 ] Installing Procedure

    DM-FX1 3) Install the Fax key unit. [3] INSTALLING PROCEDURE G Connect the flat cable to the machine connector and fold the flat cable under the FAX key unit. Fix the Fax key unit with screws. 1. FAX expansion kit installation...
  • Page 9 DM-FX1 7) Remove the rear cabinet of the machine. 11) Attach the FAX PWB. G Remove the document cover. Remove the screw and remove the G Fix it with (9) M3 screw (gold) packed together with the FAX expan- rear cabinet.
  • Page 10 DM-FX1 15) Attach the left cabinet to the copier. 18) Attach the ground plate. G Attach the left cabinet using the screw, then pass the speaker har- G Hang the hook, and fix with M3 screw (gold) packed together. ness through the hole of the PWB mounting frame and connect the M3X6 speaker harness to the connector of the copier.

  • Page 11: 4 ] Adjustments

    DM-FX1 [4] ADJUSTMENTS Section Adjustment items Adjustment procedures Density section FAX mode density adjustment <FAX mode> SIM 46-12 (Overall mode) FAX mode density adjustment <FAX mode> SIM 46-14 - 46-16 (Individual mode) Communication section Dial test <FAX mode> SIM 66-13 1.
  • Page 12 DM-FX1 6) Start transmission from the line. 2. Communication section Note: These items are factory adjusted when shipping according to H:xx L:yy FCC standards. Therefore, do not change the setting in the 1:YES 2:NO market. SENDING DTMF A. Dial test (<FAX mode> SIM 66-13)
  • Page 13 DM-FX1 [5] SIMULATIONS B. FAX mode 1. Entering the simulation mode Main A. Copy mode ∗ Content code code The following key operations allow to enter the simulation mode from the copy mode. Fax related counter display Clear key → Interruption key → “0” key → Interruption key → Main Fax ROM ver.
  • Page 14 DM-FX1 Main Initial Content Operational description code code value range Option switch display Used to display the installed options with LED on the operation panel. Key operation Display Display switch: <LED lighted when installing an option> magnification ratio key • When “A” is displayed on the display:...
  • Page 15 DM-FX1 B. FAX mode Main Initial Content Operational description code code value range FAX related counter The current Fax related counters are displayed on the LCD. display Display Copy quantity Transmission counter Reception counter Time Accumulated transmission time Accumulated reception time FAX ROM Ver.
  • Page 16 DM-FX1 G The following signals are sent to the line and the main body speaker. Display/Key operation <Signal send level> <Send signals> 18: 14400bps (V17) 0db: Signals are 01: No signal (CMLON) 19: 12000bps (V17) sent in 0db. 02: 33600bps (V34)
  • Page 17 DM-FX1 300bps signal send Used to send signals in 300bps. Display/Key operation <Signal send level> <Signal pattern> 0db: Signals are sent in 0db. 1: No signal Soft SW: Signals are sent in the 2: 111111 level set with the soft switch.

  • Page 18: 6 ] Software Switch Descriptions

    DM-FX1 [6] SOFTWARE SWITCH DESCRIPTIONS 1. Software switch changing procedure 2. Details 1) Execute SIM 66-01 in the FAX mode. When a value which is outside of the specified range is entered, the 2) Select “1.YES” in the FAX soft SW setup.
  • Page 19 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark Reserved Reserved Reserved Reserved Remote select Used to set the number for remote select reception from When a value No. setup an external telephone with binary input. However, the in the range of remote select numbers “x∗”...
  • Page 20 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark Reserved Reserved Reserved Reserved Signal send Used to set the signal send level from the Modem. The 7 (–12 level set range is 0 – 15 in the increment of 1dBm by binary dBm) input.
  • Page 21 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark MH fixing Used to fix the image data compression method in Setup in a transmission to MH. However, when SW52-7 (V.34 mode communication function) is OFF or when SW52-7 (V.34 mode function) other than V.34...
  • Page 22 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark Communication Used to set whether total communication time and total record total number of sheets are recorded or not on the time/total communication record table. number of 1.
  • Page 23 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW13 Reserved Reserved Call ring sound Used to set the reception sound volume regardless of Medium volume handset. SW13 Bit No. Silent Small Medium Large Reserved...
  • Page 24 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW15 Lower limit of Used to set the lower limit of busy tone detection time 250 ms busy tone (ON time). detection time 1: 350 ms...
  • Page 25 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW18 Reserved Reserved ∗1: Refer to Reception size Used to set the receivable document width which is By the specification informed the other party when receiving a...
  • Page 26 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW19 Output only in Effective only when SW19-1 is set to 1 (YES). Used to case of set whether protocol monitor is outputted only when a...
  • Page 27 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW21 Interval Used to set the time interval between the end of a 1 sec between the communication and a call for the next communication. end of a SW21 Bit No.
  • Page 28 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW25 Auto reduction Used to set the auto reduction ratio when “Auto ratio setup reduction print” is set to Enable. The set value is the min. reduction ratio.
  • Page 29 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW28 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Standard Read mode setup in the standard mode Reading reading setup Fine 1: cm50% (Standard 0: Without cm50%...
  • Page 30 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW31 Report output Used to set whether the communication report is Only When set to (Transmission) outputted or not after completion of transmission when “11”, set to “10”...
  • Page 31 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW33 Page number Used to set whether the page number is added to the print setup position where date and transmitter information are printed. (In memory transmission, paper number/total...
  • Page 32 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW37 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW38 Pause time Used to set the pause time. The set range is 1 sec to 2 sec...
  • Page 33 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW41 Number of Used to set the number of recall times in case of busy 2 times When it is set recall times in state of the other party or when call does not reach the...
  • Page 34 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW45 F.A.S.T mode Used to set YES/NO of the conformity for F.A.S.T 1: YES 0: NO Date format of Used to set the date format of LCD display, report...
  • Page 35 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW49 Time Used to set time designation 2 (hour) to be printed on When set to 24 designation 2 the activity report. – 31, it is set (hour) print on to “00”.
  • Page 36 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW53 DTMF send Used to set the DTMF signal send level (high group). level (High The set range is 0 – 15 with binary input in the group) setup increment of 0.5dB.
  • Page 37 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW57 Reserved Reserved Reserved SW58 V.34 Used to set whether 3429 is supported as the symbol Supported 3429 (Baud) rate in V.34 communication or not. Rate Mask...
  • Page 38 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW62 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW63 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW64 Reserved Reserved Reserved Reserved Reserved Reserved Reserved...
  • Page 39 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW67 Make time Used to set the make time when dialing at 10PPS. The 40 ms (10PPS) setup set range of N is 0 – 15 in binary input for the make time of (N +26 ms), which ranges from 26 to 41 ms.
  • Page 40 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW72 EYE-Q check Used to set whether TCF is checked or not in TCF “0” reception. reception & EYE-Q 0: "0" reception & EYE-Q 1: EYE-Q check only...
  • Page 41 DM-FX1 User Data Item Switch selection and contents of functions Initial value program Remark SW76 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW77 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW78 Reserved Reserved Reserved Reserved Reserved Reserved Reserved...

  • Page 42: 7 ] User Programs

    DM-FX1 [7] USER PROGRAMS 1. List Soft SW Number Program Name Function Note setup DEPARTMENT CODE SW30-4 Set to restrict the use of the fax function to certain departments. SETTING SW44-1 ∼ 2 DIAL MODE SETTING Set to select the type of phone line used for connection.
  • Page 43 DM-FX1 Soft SW Number Program Name Function Note setup IMAGE MEM. PRINT Set to control whether to print the first part of the original on the SW1-7 (LINE ERROR) SETTING transaction report when there is an error. SW19-7 ∼ 8, SW47-1 ∼...

  • Page 44: 8 ] Printing

    DM-FX1 Example [8] PRINTING 1=TIMER LIST 1. How to Print PRESS START KEY From the message display, select the type of list or report that you want to print. The lower line of the display shows the type of list or report you are G The activity report can be automatically printed by setting a user pro- printing.
  • Page 45 When sending a confidential fax 1) The other fax machine does not have the confidential fax receiving function or is not a SHARP product. 2) The other fax machine has only one confidential box and the passcode has not been entered in it.
  • Page 46 DM-FX1 Reception Explanation Result The reception completed successfully. P. FAIL There was a power failure during transmssion. MEM. FULL When using substitute reception, memory has become full. LENGTHOVER The received original was extra long. CONF. ERROR When receiving a confidential fax, the other fax machine entered a confidential box number that does not exist on your fax machine.
  • Page 47 DM-FX1 (Telephone Number List) You can print out a list of number stored in rapid dialing and speed dialing. (Example) P . 01 TELEPHONE NUMBER LIST SEP-10-1999 FRI 06:30 PM RAPID/SPEED # RECEIVER'S FAX # INTL TX SET RECEIVER'S NAME...
  • Page 48 DM-FX1 (Passcode List) You can print a list of your fax information and polling security information. (Example) PASSCODE LIST SEP-10-1999 FRI 06:30 PM POLL SECURITY XXXX SYSTEM# X X X X XXXX XXXX PASSCODE# XXXXXXXXXX XXXXXXXXXX RELAY ID# XXXXXXXXXXXX SENDER'S N AME...
  • Page 49 DM-FX1 (Department Usage List) You can only print out this list if auditing is turned on with a user program. Each time you print out the list, the data is erased. (Example) DEPARTMENT USAGE LIST SEP-10-1999 FRI 06:30 PM DEPT # DEPARTMENT N AME COM.

  • Page 50: 9 ] Firmware Version Up Procedure

    DM-FX1 D. Program operation [9] FIRMWARE VERSION UP PRO- (1) Starting the program CEDURE Double-click MFP.exe in the installed folder, or execute the pro- gram from the start menu. 1. Cases where firmware version up is re- ∗ This program cannot be multi-started. When it is tried to be multi- quired started, an error message will be shown.
  • Page 51 DM-FX1 <Card information> The current operation mode of the application is displayed in the The following information of the inserted card is displayed. CardType section. • Card information The File(F) menu which can be operated differs depending on the a. Kind of the card operaton mode of the application.
  • Page 52 DM-FX1 7) After completion of writing, turn off the power of the notebook PC, and remove the card adapter. 8) Set the write protect switch to ON. 4. Writing to main PWB flash ROM 1) Necessary tools Small flash card (4MB) Panasonic BN-S04MF4C (UKOG- 0008QSZZ) <RegistrationCard>...

  • Page 53: [10] Trouble Code List

    DM-FX1 [10] TROUBLE CODE LIST 1. Machine trouble codes Main Main Sub code Details of trouble Sub code Details of trouble code code Content F6∗∗ MCU-FAX communication Content FAX control PWB trouble (Overrun) trouble (MCU detection) Detail MCU-FAX control PWB...
  • Page 54 DM-FX1 2. Communication error codes Error code Communication Communication (Communication report result A. Error code identification interruption content result) column Communication error xx (xxxx) (Image quality (In print out, the communication error display is made. In FAX status error) check, “NGxxxxxx” is displayed.
  • Page 55 DM-FX1 <Communication result codes> Timeout standby for turning off the reception control channel Error Final reception signal Final reception signal code (Transmitting side) (Receiving side) Error in the first CC train Abnormal signal Abnormal signal Timeout standby for PPh NSF, DIS...
  • Page 56 DM-FX1 <Error codes 2> Error Content of communication Transmission/ codes interruption Reception Transmission length over Transmission EOL time over Reception Carrier detection time up Reception Polarity reversion detection (in Transmission/ phase C) Reception 8 min over (in phase C) Transmission...
  • Page 57 DM-FX1 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced.
  • Page 58 DM-FX1 COPYRIGHT © 1999 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Table of Contents