1. Manuals
  2. Brands
  3. HP Manuals
  4. Laptop
  5. Compaq Presario
  6. Reference manual

HP Compaq Presario,Presario 2100 Reference Manual

Hp compaq presario,presario 2100: reference guide
Hide thumbs Also See for Compaq Presario,Presario 2100:
Table of Contents

Advertisement

Quick Links

See also: Troubleshooting Manual , Reference Manual
Compaq Notebook Series
Reference Guide

Advertisement

Table of Contents
loading

Related Manuals for HP Compaq Presario,Presario 2100

Summary of Contents for HP Compaq Presario,Presario 2100

  • Page 1 Compaq Notebook Series Reference Guide...
  • Page 2 Macrovision Corporation. Reverse engineering or disassembly is prohibited. HP shall not be liable for technical or editorial errors or omissions contained herein. The information is provided “as is” without warranty of any kind, and is subject to change without notice.

  • Page 3: Important Safety Information

    Important Safety Information CAUTION To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord to connect a modem to the telephone wall jack. In Australia, the notebook must be connected to the Telecommunication Network through a line cord that meets the requirements of ACA Technical Standard TS008.
  • Page 4 COPIES AND ADAPTATIONS. Customer may make copies or adaptations of the software (a) for archival purposes or (b) when copying or adaptation is an essential step in the use of the software with an HP product so long as the copies and adaptations are used in no other manner.
  • Page 5 CD-ROM or DVD: (i) The product recovery CD-ROM or DVD and/or support utility software may only be used for restoring the hard disk of the HP product with which the product recovery CD-ROM or DVD was originally provided.
  • Page 6 FAR 52.227-19 (or any equivalent agency regulation or contract clause), whichever is applicable. The Customer agrees that it has only those rights provided for such Software by the applicable FAR or DFARS clause or the HP standard software agreement for the product involved.

  • Page 7: Table Of Contents

    Contents Getting Started with Your Notebook...1 Identifying Parts of the Notebook ...2 Series 2100 and N1050v...2 Series 2500...5 Status Lights ...8 Setting Up Your Notebook...10 Step 1: Insert the battery ...10 Step 2: Connect AC power ...11 Step 3: Connect a phone line ...12 Step 4: Turn on the notebook ...13 Step 5: Set up Windows...13 Basic Operation ...15...
  • Page 8 Batteries and Power Management...29 Managing Power Consumption ...30 How the notebook manages power automatically...30 Using Battery Power...32 To check battery status ...32 To respond to a low-battery warning...32 To recharge the battery ...33 To get the most from your batteries...33 Modem and Network Connections ...35 Using the Modem ...36 To change your modem settings...37...
  • Page 9 Display problems ...68 Hard disk drive problems ...69 Heat problems...70 Infrared problems...70 Keyboard and pointing device problems ...71 Local area network (LAN) problems...72 Memory problems...73 Modem problems ...73 PC Card (PCMCIA) problems...76 Performance problems ...76 Power and battery problems ...77 Printing problems...79 Serial, parallel, and USB problems ...80 Startup problems...81...

  • Page 10: Getting Started With Your Notebook

    Getting Started with Your Notebook Reference Guide...

  • Page 11: Identifying Parts Of The Notebook

    Getting Started with Your Notebook Identifying Parts of the Notebook Identifying Parts of the Notebook Series 2100 and N1050v NOTE Components included with the notebook may vary by geographical region and the features you selected. The following illustrations identify the standard external components included with most notebook models.
  • Page 12 13 AC adapter jack. 14 Universal serial bus ports (USB). RJ-45 jack. Connects a network cable. 16 S-video out jack. 17 Parallel port (LPT1). Use this port for a parallel printer or other parallel device. 18 Serial port (COM1). Use this port for a serial mouse, modem, printer, or other serial device.
  • Page 13 Getting Started with Your Notebook Identifying Parts of the Notebook 28 Hard disk drive. 29 Battery latch. 30 RAM (memory) cover. Reference Guide 31 Reset button. 32 Docking port (select models only). 33 Mini-PCI cover (no user parts inside).

  • Page 14: Series 2500

    Series 2500 Notebook open/close latch. One-Touch buttons. Keyboard status lights. Power button. Turns the notebook on and off. TouchPad, scroll pad, Click buttons, plus on-off button. Main status lights (left to right): power mode, hard disk activity, and battery. Infrared port (select models only). Getting Started with Your Notebook Identifying Parts of the Notebook Wireless on-off button and indicator light...
  • Page 15 Getting Started with Your Notebook Identifying Parts of the Notebook 14 AC adapter jack. 15 Two USB ports. 16 RJ-45 network jack. Connects a network cable. 17 PS/2 port. 18 Parallel port (LPT1). Use this port for a parallel printer or other parallel device. Reference Guide 19 External monitor port.
  • Page 16 26 Hard disk drive. 27 Battery latch. 28 Mini-PCI cover (no user parts inside). Getting Started with Your Notebook Identifying Parts of the Notebook 29 RAM (memory) cover. 30 Docking port (select models only). 31 Reset button. Reference Guide...

  • Page 17: Status Lights

    Getting Started with Your Notebook Identifying Parts of the Notebook Status Lights The notebook includes a number of status lights that report power and battery status, drive activity, and keyboard functions such as Caps Lock and Num Lock. The following diagram shows the main status lights on the front of the notebook. 1 Power mode.
  • Page 18 The keyboard status lights, located above the keyboard, indicate the states of the keyboard locks. 1 Caps Lock On: Caps Lock is active. 2 Num Lock On: Num Lock is active. (The Keypad Lock must also be on to use the embedded keypad.) 3 Keypad Lock On: The embedded keypad is active (Fn+F8).

  • Page 19: Setting Up Your Notebook

    Getting Started with Your Notebook Setting Up Your Notebook Setting Up Your Notebook Improper use of keyboards and other input devices has been associated with WARNING ergonomic injury. If you are using your notebook as your primary computer, or using it for extended periods, you should use it with a full-sized keyboard, monitor, and mouse.

  • Page 20: Step 2: Connect Ac Power

    Step 2: Connect AC power CAUTION Use only the AC adapter included with your notebook (or other approved adapter that meets the power requirements of the notebook). Using the wrong AC adapter could damage the notebook or adapter, cause data loss, and may void your warranty. (See the printed document Worldwide Limited Warranty and Technical Support that came with the notebook.) 1.

  • Page 21: Step 3: Connect A Phone Line

    Getting Started with Your Notebook Setting Up Your Notebook Step 3: Connect a phone line 1. Make sure the telephone line is an analog line, sometimes called a data line. (You must not use a digital line.) 2. Connect the telephone cord (RJ-11) into a telephone jack 3.

  • Page 22: Step 4: Turn On The Notebook

    Step 4: Turn on the notebook Press the power button above the left side of the keyboard. The notebook then boots up, and Windows starts automatically. Hint If your notebook does not turn on when operating on battery power, the battery may be out of power.

  • Page 23: Basic Operation

    Basic Operation Reference Guide...

  • Page 24: Operating Your Notebook

    Basic Operation Operating Your Notebook Operating Your Notebook You can start and stop your notebook using the power button. However, at certain times you may want to use other methods to start or stop the notebook, depending on power considerations, types of active connections, and startup time. Default power settings Power mode ON—Power status...

  • Page 25: To Reset The Notebook

    To reset the notebook Occasionally, you may find that Windows or the notebook has stopped responding and will not let you turn off the notebook. If this happens, try the following in the order listed: If possible, shut down Windows: press CTRL+ALT+DEL, and then select Shut Down, Restart.

  • Page 26: To Use The Touchpad

    Basic Operation Operating Your Notebook To use the TouchPad The TouchPad includes an on-off button so you can turn off the TouchPad to avoid moving the pointer accidentally when you are typing. The indicator light turns off when you turn off the TouchPad. 1 Select buttons.

  • Page 27: To Use The Function Hot Keys

    To use the function hot keys The combination of the Fn key plus another key creates a hot key—a shortcut key sequence—for various system controls. To use a hot key, press and hold Fn, press the appropriate second key, and then release both keys. This hot key Does this Fn+F1...

  • Page 28: To Use The One-Touch Buttons

    Basic Operation Operating Your Notebook To use the One-Touch buttons Your notebook includes five One-Touch buttons that can start any application or open a document or Web site with a single press. Press the One-Touch button to open the corresponding application, document, or Web site.

  • Page 29: To Use The Windows And Applications Keys

    To use the Windows and Applications keys The Windows key brings up the Windows Start menu. This is the same as selecting the Start button on the taskbar. The Applications key brings up the shortcut menu for the current application. This is the same menu that appears when you right-click while pointing at the application.

  • Page 30: Using Cds Or Dvds

    Basic Operation Using CDs or DVDs Using CDs or DVDs To insert or remove a CD or DVD CAUTION Do not remove a CD or DVD while the notebook is reading it, or the notebook could stop responding and you could lose data. To avoid damage to the disk or drive, be sure to press the CD or DVD firmly onto the spindle.

  • Page 31: To Play Dvd Movies

    Select Start > All Programs > Multimedia > DVD Player > InterVideo WinDVD. Hint For best performance while playing movies on battery power, set the Control Panel Power Scheme to Portable/Laptop. Important DVDs can have regional codes embedded in the disc data. These codes prevent DVD movies from being played outside the region of the world in which they are sold.

  • Page 32: Securing Your Notebook

    Basic Operation Securing Your Notebook Securing Your Notebook To set up password protection You can protect your notebook from access by another user when you set up password protection, which is available through Windows and through the BIOS Setup utility. See details on the BIOS Setup Utility in the “Troubleshooting and Maintenance”...

  • Page 33: To Attach A Security Cable

    Basic Operation Securing Your Notebook To attach a security cable Your notebook includes a built-in connector to allow you to secure the notebook with a cable and a lock (such as the Kensington MicroSaver lock system, available at many notebook stores). 1.

  • Page 34: To Lock The Hard Disk Drive

    Basic Operation Securing Your Notebook To lock the hard disk drive The notebook enables you to lock its internal hard disk drive to help keep your information secure. Hard disk drive lock does not protect a second hard disk drive installed in the module bay.

  • Page 35: Taking Care Of Your Notebook

    Taking Care of Your Notebook Follow these recommendations to maintain your notebook during everyday use and prevent potential physical damage or data loss. To protect your hard disk drive Hard disk drives, as well as other internal components, are not indestructible and can be damaged by inappropriate handling and operation.

  • Page 36: To Safeguard Your Data

    Basic Operation Taking Care of Your Notebook To safeguard your data Do not use a pointing device or activate any other device that interrupts operation while the system is starting or stopping. Back up your work regularly. Copy files to floppy, CDs, DVDs, and other media, or network drives.

  • Page 37: Batteries And Power Management

    Batteries and Power Management Reference Guide...

  • Page 38: Managing Power Consumption

    Batteries and Power Management Managing Power Consumption Managing Power Consumption When you’re running your notebook on battery power, you can maximize operating time without compromising performance. Your notebook is designed to help you reduce power consumption and extend battery life. During idle periods, the notebook automatically enters power-saving modes after specified timeout periods.
  • Page 39 The notebook can also enter Hibernation if battery power reaches a critically low level. If this happens, you will find on resuming that all your data has been saved, but some functions may be disabled. To resume normal operation, restore power by connecting an AC adapter or installing a charged battery, and then shut the notebook off and restart it.

  • Page 40: Using Battery Power

    Batteries and Power Management Using Battery Power Using Battery Power To check battery status From the battery status light Check the battery status light on the notebook. From the Windows taskbar The Windows taskbar can display a power icon that provides detailed battery status information (see Windows Help for details).

  • Page 41: To Recharge The Battery

    Once the notebook enters Hibernation in this way, you won’t be able to turn it on again until you restore power by doing one of the following: Replace the battery with a charged one. Plug in the AC adapter. Note If you plug in the AC adapter, you can continue to work while your battery recharges.
  • Page 42 Batteries and Power Management Using Battery Power If your notebook has a wireless on-off button, turn off the wireless function when you’re not using it. Press the wireless on-off button to turn off the light. If you have a PC Card, such as a network card, remove it when you’re not using it.

  • Page 43: Modem And Network Connections

    Modem and Network Connections Reference Guide...

  • Page 44: Using The Modem

    Modem and Network Connections Using the Modem Using the Modem You can connect your modem to a telephone line and communicate throughout the world. You can explore the Internet, send and receive e-mail messages, and use your notebook to send and receive faxes. Your notebook contains several software programs that work with your modem: Internet Explorer, for browsing the World Wide Web Outlook Express, for sending and receiving e-mail messages...

  • Page 45: To Change Your Modem Settings

    Special restrictions in certain countries Many countries impose a blackout period after a modem repeatedly fails to connect to a service provider. The number of failed attempts and the period you must wait before trying again differ from country to country. Check with your telephone company.

  • Page 46: Connecting To A Local Area Network (Lan)

    Modem and Network Connections Connecting to a Local Area Network (LAN) Connecting to a Local Area Network (LAN) You can connect to local area networks (LANs). LANs give you access to network resources, such as printers and file servers on your corporate network, and possibly to the Internet.

  • Page 47: Making Wireless Network Connections (Select Models Only)

    Modem and Network Connections Making Wireless Network Connections (select models only) Making Wireless Network Connections (select models only) If your notebook includes a wireless on-off button, you can connect by radio to an 802.11 wireless local area network (LAN) and access notebooks and other resources on the network.
  • Page 48 Modem and Network Connections Making Wireless Network Connections (select models only) 2. A list of available networks appears. Select the network you want, enter the encryption key if required, and select Connect. If the network you want is not on the list, select Advanced > Configure, and enter the required network parameters.

  • Page 49: To Turn Wireless Communication On And Off

    5. If you want to use encrypted communication, uncheck the automatic key option, and then select the following parameters: Key: ASCII passphrase or hexadecimal key string. Key format: ASCII for passphrase, hexadecimal for key string. Key length: smaller number for 64-bit encryption, larger number for 128-bit. 6.
  • Page 50 Modem and Network Connections Making Wireless Network Connections (select models only) Turning off communication and ending a connection 1. Important: close any files that reside on other network notebooks. 2. To turn off the wireless 802.11 communication without turning off the notebook, press the wireless on-off button.

  • Page 51: Making Wireless Bluetooth Connections (Select Models Only)

    Making Wireless Bluetooth Connections (select models only) If your notebook includes Bluetooth wireless capabilities, you can use it to make short-range radio connections to a wireless personal area network (PAN) and access other Bluetooth-compatible devices, such as other notebooks, cell phones, and printers.

  • Page 52: To Prepare For Bluetooth Connections

    4. On the General tab, check the following settings: Give your notebook a unique name that will identify it to other Bluetooth users. Set the notebook type to Laptop. Select the security mode you want to use. 5. On the Information Exchange tab, check the following settings: Check the directory you want to make available to other Bluetooth users for sharing files, both sent and received.

  • Page 53: To Send Or Receive Files Using Bluetooth

    Making Wireless Bluetooth Connections (select models only) Detailed information about these and other advanced settings are included in the online help. To create your business card, you can open Microsoft Outlook, then open the address book and create a new contact. After entering your personal information, select File, Export To vCard File, and store the file in your business card directory.

  • Page 54: Add-On Devices

    Add-On Devices Reference Guide...

  • Page 55: Connecting External Devices

    Add-On Devices Connecting External Devices Connecting External Devices Connecting PC Cards The notebook PC Card slot is available for storing data and expanding the communication capabilities of the notebook. The notebook supports standard Type II and III PC Cards (PCMCIA and CardBus). To insert or remove a PC Card Inserting a PC Card 1.
  • Page 56 Removing a PC Card CAUTION Before removing a PC Card, you must use the Eject Hardware or Safely Remove Hardware icon in the taskbar, or shut down the notebook. Otherwise, you could lose data. 1. Before removing the card, select the Eject Hardware or Safely Remove Hardware icon in the taskbar, and then select the card you want to remove.

  • Page 57: To Connect An Audio Device

    Add-On Devices Connecting External Devices To connect an audio device You can plug in an external microphone, external speakers, or headphones. In addition, if you connect your notebook to the port replicator, you can plug in a stereo source (such as a CD player) or a device that accepts digital audio (such as a digital audio recorder).

  • Page 58: To Use An External Monitor

    To use an external monitor Connecting an external monitor 1. Select Start > Turn Off Computer > Turn Off. 2. Connect the monitor cable from the monitor to the monitor port on the back of the notebook. 3. Connect the monitor to a power source and turn it on. 4.

  • Page 59: To Connect An Ieee 1394 Device (Select Models Only)

    Add-On Devices Connecting External Devices Using dual display mode You can extend your desktop by connecting an external monitor to your notebook. 1. Select Start > Control Panel > Appearance and Themes > Display. 2. Select the Settings tab. 3. Select the second display, and then select the option to extend the desktop. You can set different resolutions and numbers of colors for each display.

  • Page 60: To Connect An Infrared Device (Select Models Only)

    To connect an infrared device (select models only) Note: select models only If your model has an infrared port, a small, rectangular lens located on the front of the notebook provides wireless, serial communication between the notebook and other infrared devices such as printers or other notebooks. Using the infrared port Make sure the infrared ports of your notebook and the other device lie in a straight line.

  • Page 61: To Use A Port Replicator (Select Models Only)

    Add-On Devices Connecting External Devices To use a port replicator (select models only) A port replicator provides your notebook with external connections that you can leave in place whenever you remove the notebook from your desk. Instead of disconnecting and reconnecting peripheral devices, you can simply undock and dock the notebook.
  • Page 62 To dock to the port replicator 1. Plug in the AC adapter, and then connect it to the back of the port replicator. You can also operate the port replicator using power from the notebook battery. 2. Remove the rubber cover from the docking connector on the bottom of the notebook.
  • Page 63 Add-On Devices Connecting External Devices To undock from the port replicator 1. Press down the undock button on the right side of the port replicator. 2. Lift the notebook out of the port replicator. Reference Guide...

  • Page 64: Installing Additional Ram (Memory)

    Installing Additional RAM (Memory) The notebook has two slots that hold two RAM modules. At least one slot contains a RAM module installed at the factory. You can use both slots to expand your RAM. To install a RAM expansion module Use only PC2100 DDR-266 MHz or higher RAM.
  • Page 65 Add-On Devices Installing Additional RAM (Memory) 4. Insert the RAM board into the connector at about a 30 degree angle until it is fully inserted. Then press down at both sides until both latches snap closed. Series 2100 and 1050v Series 2500 5.

  • Page 66: To Remove A Ram Expansion Module

    To remove a RAM expansion module You may want to remove a RAM module so you can install a larger one. You’ll need a small Phillips screwdriver for these steps. CAUTION Your notebook internal components are extremely sensitive to static electricity and can be permanently damaged by it.
  • Page 67 Add-On Devices Installing Additional RAM (Memory) 4. Release the two latches at the sides of the RAM board, so the free edge of the board pops up. Series 2100 and 1050v Series 2500 5. Pull the board out of the connector. 6.

  • Page 68: Replacing The Hard Disk Drive

    Replacing the Hard Disk Drive To replace the hard disk drive You will need a small Phillips screwdriver for this procedure. 1. Unplug the AC adapter, if connected. 2. Remove the battery. 3. Turn the unit bottom side up. 4. Use a pointed tool to remove the plugs from the two screw holes, then remove the two screws.

  • Page 69: To Replace The Hard Disk Drive Holder

    Add-On Devices Replacing the Hard Disk Drive To replace the hard disk drive holder If you are installing a new hard drive that does not have a holder, you can remove the holder parts from the old hard drive. You’ll need a small Phillips screwdriver for this procedure.

  • Page 70: To Prepare A New Hard Disk Drive

    Add-On Devices Replacing the Hard Disk Drive To prepare a new hard disk drive When you install a new hard disk drive, you also need to prepare it to be able to work with your notebook. If you want to restore the Windows software and operating system that were originally installed on your notebook, use the QuickRestore System Recovery CD that came with your notebook.

  • Page 71: Troubleshooting And Maintenance

    Troubleshooting and Maintenance Reference Guide...

  • Page 72: Troubleshooting Your Notebook

    Troubleshooting and Maintenance Troubleshooting Your Notebook Troubleshooting Your Notebook This section contains solutions to many types of problems you might have with your notebook. Try the solutions one at a time, in the order in which they are presented. Here are some other sources of information for troubleshooting: Use the Windows troubleshooters.

  • Page 73: Cd-Rom And Dvd Problems

    If you hear a loud high-pitched whine (feedback) from the speakers In the Volume Control, try reducing the Master volume by double-clicking the speaker icon in the taskbar. In Volume Control, select Options > Properties, and select the microphone option for the playback settings. Then in Volume Control, make sure the microphone is muted.

  • Page 74: Display Problems

    Troubleshooting and Maintenance Troubleshooting Your Notebook Restart the system: remove the disc from the drive, and select Start > Turn Off Computer > Restart. If you created the CD on a DVD/CD-RW combo-type drive, try using a different media brand. Read and write quality may vary for media. If a DVD movie doesn’t fill the screen Each side of a double-sided DVD has a different format (standard or widescreen).

  • Page 75: Hard Disk Drive Problems

    If an external display does not work Check the connections. Press Fn+F5 in case the external monitor was disabled. (Do this three times to return to the state you started from.) The external monitor may not be detected. In the BIOS Setup utility, try setting Video Display Device to Both in the System Devices menu.

  • Page 76: Heat Problems

    Troubleshooting and Maintenance Troubleshooting Your Notebook Heat problems Your notebook normally gets warm during routine operation. If the notebook gets abnormally hot Always set the notebook on a flat surface, so that air can flow freely around and underneath it. Make sure the air vents on the bottom and sides of the notebook are clear.

  • Page 77: Keyboard And Pointing Device Problems

    Keyboard and pointing device problems Use these suggestions for built-in or external devices. If the pointer is difficult to control Adjust the pointer controls. Select Start > Control Panel > Printers and Other Hardware > Mouse. If the TouchPad doesn’t work Press the TouchPad on-off button to turn on the light.

  • Page 78: Local Area Network (Lan) Problems

    Troubleshooting and Maintenance Troubleshooting Your Notebook Local area network (LAN) problems If the built-in network adapter doesn’t connect to the LAN Check all cables and connections. Try connecting at a different network station, if available. Make sure the LAN cable is Category 3, 4, or 5 for 10Base-T operation, or Category 5 for 100Base-TX operation.

  • Page 79: Memory Problems

    Memory problems If a message says you are out of memory Make sure drive C is not running low on free space. If you are having memory problems while running MS-DOS programs, use the MS-DOS or Application and Software troubleshooter in Windows Help. Select Start >Help and Support.
  • Page 80 Troubleshooting and Maintenance Troubleshooting Your Notebook If the modem doesn’t dial or no dial tone is detected Check all cables and connections. Connect a standard telephone to the phone line and make sure the line is working. Make sure someone else isn’t using the same phone line. Try another telephone line, preferably one normally used for a fax machine or modem.
  • Page 81 Open the hardware Device Manager. Select Start > Control Panel > Performance and Maintenance > System. If the modem is disabled, try to enable it. If it has a conflict, try disabling another device. If you’re running fax software using fax Class 2, try using Class 1. If the modem dials but you can’t hear it If your model has an audio mute light, make sure it is turned off.

  • Page 82: Pc Card (Pcmcia) Problems

    Troubleshooting and Maintenance Troubleshooting Your Notebook PC Card (PCMCIA) problems If the notebook doesn’t recognize a PC Card Remove and reinsert the PC Card. Restart the notebook. Select Start > Turn Off Computer > Restart. Try the card in another notebook to see whether the card functions properly. Zoomed Video is not supported.

  • Page 83: Power And Battery Problems

    Press CTRL+ALT+DEL and use Task Manager to see if an application is not responding. Restart the notebook. Select Start > Turn Off Computer > Restart. Some file browsers respond slowly while processing graphics or waiting for broken network connections to time out. If the notebook hard disk drive frequently runs (as indicated by the hard drive light on the front of the notebook) while the notebook appears to be paused or running slowly, Windows is likely spending excess time writing to its swap file...
  • Page 84 Troubleshooting and Maintenance Troubleshooting Your Notebook If the battery doesn’t charge Make sure the AC adapter is fully plugged into the power source and the notebook, and that the light on the adapter is on. If you’re using a power strip, remove the AC adapter from the power strip and plug it directly into a wall outlet.

  • Page 85: Printing Problems

    If the notebook doesn’t enter Standby mode as expected If you have a connection to another computer, the notebook won’t suspend if the connection is active. If the notebook is performing an operation, it normally waits for the operation to finish before going into Standby.

  • Page 86: Serial, Parallel, And Usb Problems

    Troubleshooting and Maintenance Troubleshooting Your Notebook Serial, parallel, and USB problems If a serial mouse doesn’t work Make sure you followed the manufacturer’s installation instructions completely and have installed the mouse properly. If not, repeat the procedure. Make sure the port connection is secure. Restart the notebook.

  • Page 87: Startup Problems

    If the USB port is not working Contact the vendor of the peripheral device for the latest USB drivers. Check the port settings in Control Panel. Open the hardware Device Manager, and then double-click Universal Serial Bus Controller. Startup problems If the notebook doesn’t respond when you turn it on Connect the AC adapter.

  • Page 88: Wireless Problems

    Troubleshooting and Maintenance Troubleshooting Your Notebook If the notebook takes a long time to resume after being suspended The notebook can routinely take a minute or more to resume if it has a network card installed. While the operating system is loading drivers and checking hardware and network connections, you will see a blinking cursor on your display.
  • Page 89 If you cannot connect to a particular notebook on the network Make sure the notebook is properly connected to the network. Make sure your TCP/IP setup is correct for your network. Select Start > Control Panel > Network Connections. If you can connect, but the network is slow Check whether you might be in an area served by more than one wireless LAN.

  • Page 90: Configuring The Notebook

    Troubleshooting and Maintenance Configuring the Notebook Configuring the Notebook The BIOS Setup utility helps you configure your notebook operation. To run the BIOS Setup utility The BIOS (Basic Input and Output System) Setup utility enables you to make changes to the notebook system configuration, and to tailor the operation of your notebook to your individual work needs.
  • Page 91 Setting Description BIOS Revision Shows the current BIOS version. System Time Sets the time using 24-hour format. Values set take effect immediately. System Date Sets the date using dd/mm/yy format (except English, which uses mm/dd/yy format). Language Sets the language for BIOS Setup. Internal Hard Disk Sets the hard disk drive type and various parameters.
  • Page 92 Troubleshooting and Maintenance Configuring the Notebook Setting Description User Password is Shows if a user password is set. Administrator Shows if an administrator password is set. Password is Set User Password Press ENTER to set, change, or clear the user password. The password can have no more than 8 characters (0-9, A-Z), and cannot include special or accented characters.

  • Page 93: To Change Video Memory Settings Using Bios Setup Utility

    To change video memory settings using BIOS Setup utility The notebook comes with either 32MB or 16MB of video memory. Note Changing your video memory to 8MB, 16MB, 32MB, or 64MB may change the performance of your notebook, depending on your selection. To change your video memory: Select Start >...

  • Page 94: Reinstalling And Updating Software

    Troubleshooting and Maintenance Reinstalling and Updating Software Reinstalling and Updating Software Your notebook includes two features that allow you to install individual software applications or to restore the entire contents of your hard drive: QuickRestore System Recovery CD, included with the notebook, allows you to restore your hard drive to the factory image.

  • Page 95: Reference Information

    Reference Information Reference Guide...

  • Page 96: Modem Reference Information

    Reference Information Modem Reference Information Modem Reference Information You can customize the operation of the modem using AT commands and S-registers. You can do this from Phone and Modem Options in Control Panel, from most communications software, or by using terminal mode in your software. Note You should have a good understanding of modems and how they operate before you change default settings.
  • Page 97 Conexant AT Commands (Advanced Users Only) Command (Conexant) 0=go on-line, 1=go on-line and initiate retrain sequence. Force pulse dialing. 0=enable result codes to DTE (default), 1=disable. Select S-register n as default. Sn=v Set default S-register n to value v. Force DTMF dialing. Report result codes: 0=short form (terse), 1=long form (verbose) (default).
  • Page 98 Reference Information Modem Reference Information Conexant AT Commands (Advanced Users Only) Command (Conexant) +ESA=a,b,c,d, Controls operation of synchronous access mode: e,f,g,h a=0 specifies in transparent sub-mode, modem transmits 8-bit SYN sequence on idle. b=0 specified in framed sub-mode, modem transmits HDLC flags on idle (default and fixed). c=0 specifies in framed sub-mode, modem transmits abort on underrun in middle of frame (default);...
  • Page 99 Conexant AT Commands (Advanced Users Only) Command (Conexant) +VCID=n Set caller ID reporting: 0=disable (default), 1=enable with formatted presentation, 2=enable with unformatted presentation. +VRID=n Report caller ID: 0=use formatted presentation, 1=use unformatted presentation. -QCPC Use full startup procedures on next connection, then select startup procedure defined by +PQC. -QCPS=n 0=do not allow modem to save generated quick-connect profile, 1=allow (default) &Cn...
  • Page 100 Reference Information Modem Reference Information Conexant AT Commands (Advanced Users Only) Command (Conexant) +MS=a,b,c,d, Select modulation (b, c, d, e, and f are optional). a is the carrier (allowable rates in parentheses): B103 (300), B212 (1200 Rx/75 Tx or 75 Rx/1200 Tx), V21 (300), V22 (1200), V22B (1200/2400), V23C (1200), V32 (4800/9600), V32B (4800–14400), V34 (2400–33600), K56 (32000–56000), V90 (28000–56000), V92 (downstream: 28000–56000;...
  • Page 101 Conexant AT Commands (Advanced Users Only) Command (Conexant) +FLO=a Set flow control type: 0=XON/XOFF and RTS/CTS flow control turned off; 1=XON/XOFF flow control in either direction; 2=RTS for flow control of modem by DTE, and CTS for flow control of DTE by modem.
  • Page 102 Reference Information Modem Reference Information Register Function (Conexant) Number of rings to auto-answer. Ring counter. Escape character. Line termination character. Response formatting character. Command line editing character. Wait time for dial tone. Wait time for carrier. Pause time for dial delay modifier. Carrier loss disconnect time.

  • Page 103: Safety Information

    Safety Information Power Cords The power cord supplied with the notebook AC adapter should match the plug and voltage requirements for your local area. Regulatory approval for the AC adapter has been obtained using the power cord for the local area. However, if you travel to a different area or need to connect to a different outlet or voltage, you should use one of the power cords listed below.

  • Page 104: Battery Safety

    Reference Information Safety Information Battery Safety To avoid risk of fire, burns, or damage to your battery pack, do not allow a metal object to touch the battery contacts. Do not disassemble the battery. There are no serviceable parts inside. Do not dispose of the battery pack in fire or water.

  • Page 105: Led Safety

    Do not attempt to make any adjustment of the unit. Avoid direct exposure to the laser beam—do not open the unit. CLASS 1 LASER PRODUCT LASER KLASSE 1 LED Safety The infrared port located on the front of certain models is classified as a Class 1 LED (light-emitting diode) device according to International Standard IEC 825-1 (EN60825-1).

  • Page 106: Exposure To Radio Frequency Radiation

    Reference Information Safety Information Exposure to Radio Frequency Radiation The radiated output power of the IEEE 1394, 802.11 and Bluetooth internal wireless radio is far below the FCC radio frequency exposure limits. Nevertheless, the wireless radio shall be used in such a manner that the potential for human contact during normal operation is minimized.

  • Page 107: Regulatory Information

    Regulatory Information This section presents information that shows how your notebook complies with regulations in certain regions. Any modifications to your notebook not expressly approved by the manufacturer could void the authority to operate the notebook in these regions. U.S.A. This notebook has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 108 Reference Information Regulatory Information Applicable certification jack USOC = RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product.

  • Page 109: Regulatory Information

    The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a notebook or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business,...

  • Page 110: European Union

    Reference Information Regulatory Information The internal wireless radio complies with RSS 210 of Industry Canada. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
  • Page 111 Reference Information Regulatory Information Germany: License required for outdoor installations. Check with reseller for procedure to follow. Netherlands: License required for outdoor installations. Check with reseller for procedure to follow. Italy: Indoor or outdoor use in a public area requires a user license. Die Geräte wurden gemäß...

  • Page 112: Japan

    Reference Information Regulatory Information Questa apparecchiatura è stata approvata in conformità alla Decisione del Consiglio 98/482/EC che regolamenta, in seno all’Unione Europea, la connessione di singoli terminali alla rete telefonica pubblica commutata (PSTN) e alla rete wireless in radio frequenza. Tuttavia, a causa delle differenze esistenti tra i singoli servizi PSTN forniti nei diversi paesi, l’approvazione in sé...

  • Page 113: New Zealand

    TELEC approval number: D02-0005JP Name of Equipment: T60H424 New Zealand Conexant AMC20493-KT5 Data Fax Modem PTC 211/02/071 PTC200 General Warning The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network.

  • Page 114: Russia

    Reference Information Regulatory Information PTC200 7.5.2 (3) (4) Ringer Sensitivity This device may be subject to ringing or bell tinkle when certain other devices are connected to the same line. If this occurs, the problem should not be referred to the Telecom Faults Service. Associated Software Limits of Compliance Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the application software or PC equipment associated with this device.
  • Page 115 (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The HP F1454, F1781, F4600, F4814, F4813, F5104, 0950-4334, and 0950-4406 ac/dc adapters used with this product are designed to operate on all power systems, other than IT power systems.

  • Page 116: Index

    Index AC adapter compatibility, 11, 54 connecting, 11 AC adapter jack location, 3, 6 adding RAM, 57 AdHoc wireless network setup, adjusting brightness, 19 volume, 19 airplanes, wireless communication in, 41, 43 ALT GR key, 21 antistatic precautions, 57, 59 Applications key, 21 AT commands, 37, 90 audio...
  • Page 117 + Page Down (decrease audio), + Page Up (increase audio), 19 hard disk drive caring for, 28 Hibernation partition, 61, 87 holder, 62 location, 4, 7 locking, 26 protecting, 27 replacing, 61 troubleshooting, 69 Hibernation mode definition, 16 Hibernation partition, 61, 87 hot computer, 70 hot keys, 19 IEEE 1394 port...
  • Page 118 hard disk drive, 61 hard drive holder, 62 PC Card, 49 RAM, 59 reset button, 17 resetting, 17 safety battery use, 98 infrared port, 99 laser, 98 power cords, 97 wireless communication, 41, 43 safety information, iii saving battery power, 33 scroll pad, 2, 5 secondary display, 51 security...

This manual is also suitable for:

Compaq presario,presario 2500Evo n1050vDm760a#aba - compaq presario 2585us

Table of Contents