Page 1 PRIMERGY RX300 S3 User’s Guide Areas Covered Before Reading This Manual This section explains the notes for your safety and conventions used in this manual. Chapter 1 Overview This chapter explains component names and basic operations of this server, as well as an overview of the software provided with this server.
Page 2 It is the customer's responsibility to maintain backup copies in advance. In case of data loss, Fujitsu assumes no liability for data maintenance or restoration and damages that occur as a result of the data loss for any reason, except for items covered under warranty.
Page 3 PRIMERGY RX300 S3 User’s Guide Remarks ■ Warning Descriptions Various symbols are used throughout this manual. These are used to emphasize important points for your safety and that of others. The following are the symbols and their meanings. Fully understand these symbols when reading this manual.
Page 4 ■ Entering Commands (Keys) Command entries are displayed in the following way. • At each blank in a command line (as pointed out above), press the [Space] key once. • When using Windows or DOS OS, commands are not case sensitive. •...
Page 5 PRIMERGY RX300 S3 User’s Guide ■ Abbreviations The following expressions and abbreviations are used throughout this manual. table: Abbreviations of Product Names Product name Expressions and abbreviations PRIMERGY RX300 S3 This server or the server ® Windows Server 2003 R2 Windows ™...
Page 6 ■ Latest Information about Software Provided with This Server For the latest information regarding ServerStart and other software provided with this server, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com). Warning and Caution Labels Warning and caution labels are found on the server.
Page 7: Table Of Contents
PRIMERGY RX300 S3 User’s Guide Contents Chapter1 Overview 1.1 RX300 S3 ..........14 1.2 Supplied Software .
Page 8 3.1.2 Open/create a Configuration File ....... 60 3.1.3 RAID and Disk Wizard ........61 3.1.4 OS Installation Wizard .
Page 9 PRIMERGY RX300 S3 User’s Guide Chapter 5 Operations after OS Installation 5.1 Memory Dump/Paging File Setting ..... . 136 5.1.1 How to Obtain Memory Dump for Windows Server 2003 and Windows Server 2003 x64 .
Page 10 Chapter 7 Installing Internal Options 7.1 Before Installing Internal Options ..... . 180 7.2 Installing/Removing the Top Cover ..... . 182 7.2.1 How to Remove the Top Cover .
Page 11 PRIMERGY RX300 S3 User’s Guide 8.1.6 The Peripheral Configuration Submenu ......236 8.1.7 The PCI Configuration Submenu .......238 8.1.8 The Advanced System Configuration Submenu .
Page 12 Appendix A Server Specifications ....... . 290 A.1 Diskless Type ..........290 B Specifications for Internal Options .
Page 13: Chapter1 Overview
Chapter1 Overview This chapter explains component names and basic operations of this server, as well as an overview of the software provided with this server. In addition, the workflow, from placing the server to starting the operation, is also described. 1.1 RX300 S3 .
Page 14: Rx300 S3
Chapter1 Overview 1.1 RX300 S3 This server has the following features. ■ High Reliability ● Advanced Memory Protection Function The server supports the Chipkill function using PC2-4200F (DDRII 533) compliant memory (Fully Buffered DIMM). Also, memory mirroring function is supported to enable data recovery in the event of a memory error.
Page 15 PRIMERGY RX300 S3 User’s Guide ■ High-speed Processing   ● Dual Core Intel Xeon Processors The server can have up to two dual core Intel® Xeon® processors for high-speed data processing (one processor in standard servers). The server supports the 64-bit processing and the Hyper-Threading function providing high-efficiency and high-speed processing.
Page 16: Supplied Software
Chapter1 Overview 1.2 Supplied Software ServerStart for supporting setup and high reliability tools for avoiding problems during server operation are supplied with this server. 1.2.1 Setup Support Tool - ServerStart ServerStart is a setup support tool that helps to install PRIMERGY. It offers easy server installation and proper installation of recommended drivers.
Page 17 PRIMERGY RX300 S3 User’s Guide ● Supported OS The following OSs can be installed using ServerStart V5.603. ® ™ • Microsoft Windows Server 2003, Standard Edition ® ™ • Microsoft Windows Server 2003, Enterprise Edition ® ™ • Microsoft Windows Server 2003, Standard x64 Edition ®...
Page 18 Chapter1 Overview ■ Intuitive User Interface The intuitive user interface allows you to easily set the necessary information. ● Main Window When ServerStart is started, the following window appears. The window and tool bar differ depending on the mode. ● Toolbar In Guided Mode/Expert Mode Brings you to...
Page 19 PRIMERGY RX300 S3 User’s Guide ● Wizard Window Clicking a wizard displays a wizard window. Set items in the wizard window. To move to a step in the next wizard window, click the operation button at the bottom of the window. Clicking [help] displays a tip for setting the item.
Page 20: High Reliability Tools
Chapter1 Overview 1.2.2 High Reliability Tools High reliability tools are a comprehensively useful set of software for stable system operations of the server. The following tools have respective roles to manage normal operations or recovery from errors. • Server Monitoring Tools •...
Page 21: Installing High Reliability Tools
PRIMERGY RX300 S3 User’s Guide ■ LAN Driver Advanced Setup Tools LAN Driver Advanced Setup Tool sets details on the LAN, including the use of the Teaming function and VLAN configuration. ● Broadcom Advanced Control Suite (BACS) BACS is a tool for setting details on the onboard LAN when it is used to use the Teaming (load balance) function between the onboard LAN, or to setup a VLAN using the onboard LAN.
Page 22: Component Names And Functions
Chapter1 Overview 1.3 Component Names and Functions This section explains the component names and functions of the server. 1.3.1 Server (Front View) a 3.5-inch storage bay Install the internal hard disk unit or internal backup device into the server unit. b Floppy disk drive Writes/reads data to/from a floppy disk.
Page 23 PRIMERGY RX300 S3 User’s Guide h Reset switch ( ) Pressing this switch resets and restarts the system. When the hard disk access LED lights, do not reset the system. Data in the hard disk may be damaged. i Maintenance switch ( ) This switch is used only by maintenance personnel.
Page 24: Server (Rear View)
Chapter1 Overview 1.3.2 Server (Rear View) [Standard card slot] [With basic card slot conversion mechanism] a Power supply unit 1 (installed as standard) One power supply unit is installed by default. Up to two units can be installed. Adding a power supply unit enables the redundant power supply function. b Power supply unit failure LED The LED indicates the power supply unit status.
Page 25 PRIMERGY RX300 S3 User’s Guide h Rear maintenance LED / System identification LED ( This LED lights amber when the server is not turned on (standby mode). When the server is turned on and an error is detected in a server component, this LED lights or blinks amber (OFF in normal status).
Page 26: Server (Internal)
Chapter1 Overview 1.3.3 Server (Internal) a Power supply unit b Memory slot Contains memory. c CPU socket Install the CPU. One socket is installed by default. Up to two sockets can be installed. d System fan The system fan has a redundant configuration and a failed system fan can be replaced while the system is running.
Page 27: Baseboard
PRIMERGY RX300 S3 User’s Guide 1.3.4 Baseboard [Rear] [Front] a PCI slot Contains an expansion card. b Serial port connector Serial port expansion kit is plugged in. c Parallel port connector Parallel port expansion kit is plugged in. d Memory slot Contains memory.
Page 28 Chapter1 Overview f Power connector g Operation panel connector h IDE connector An IDE cable of the internal CD-ROM or internal DVD-RAM drive is plugged in. i Floppy disk connector j SAS connector...
Page 29: Standard Operations
PRIMERGY RX300 S3 User’s Guide 1.4 Standard Operations This section explains standard server operations, including how to turn the server on/ off and to insert/eject a floppy disk. 1.4.1 Opening the Rack Door This section explains how to open the front and rear doors of the 40U standard rack.
Page 30 Chapter1 Overview Turn the handle in the direction of the arrow and pull it forward. Turn and then pull ■ Opening the Rear Door Turn the rack key and pull the rack handle up.
Page 31 PRIMERGY RX300 S3 User’s Guide Turn the handle in the direction of the arrow and pull it forward. Turn and then pull Unless you are inserting/removing media or turning the power on/off, keep the rack door closed. Doing so blocks electric waves from cell phones, etc.
Page 32: Turning On The Server
When operating the device outside of this operating environment, the server may operate improperly, damage data etc. Furthermore, Fujitsu cannot be held responsible for any related damage, malfunction, or loss of data, etc. • Be sure to wait for 10 seconds or more after shutdown before turning the server on.
Page 33: Turning Off The Server
PRIMERGY RX300 S3 User’s Guide 1.4.3 Turning Off the Server • In the event of smoke or sparks, immediately unplug the electric cord. Failure to do so may lead to a fire or electrocution. • When turning off the server, be sure to follow the procedures described in this section.
Page 34: Inserting And Ejecting A Floppy Disk
Chapter1 Overview ■ Cautions for Turning the Power On/Off (for a Windows OS) For the power switch of this server, you can specify the following operation modes depending on the OS settings. • For Windows Server 2003 "Do Nothing", "Prompt Input", "Standby", "Hibernation", or "Shutdown" (normally, "Shutdown" is specified).
Page 35 PRIMERGY RX300 S3 User’s Guide ■ Inserting the Floppy Disk Insert the floppy disk into the floppy disk drive from the shutter side. When clicking into place, the floppy disk eject button pops out. Floppy disk eject button Shutter Label side up ■...
Page 36: Inserting And Ejecting A Cd-Rom (Dvd-Ram)
Chapter1 Overview 1.4.5 Inserting and Ejecting a CD-ROM (DVD-RAM) This section explains how to insert and eject a CD-ROM, and DVD-RAM. ■ Cautions for Handling CD-ROM Drive • Use the drive in a dry place with low airborne dust levels. Entry of water, a paper clip, or other liquids or metal objects can cause electric shock or failures.
Page 37 PRIMERGY RX300 S3 User’s Guide ■ Inserting the CD-ROM Make sure the server is turned on and press the CD-ROM eject button. The CD-ROM tray comes out a little. CD-ROM eject button Pull the CD-ROM tray out. CD-ROM tray Place the CD-ROM at the center of the tray.
Page 38 Chapter1 Overview Move the tray back. Push the tray gently until it clicks into position. CD-ROM unit bezel Push the center of the CD-ROM unit bezel gently until the tray clicks into position. ■ Ejecting the CD-ROM ■ To eject the CD-ROM, press the CD-ROM eject button in the same way as steps 1 to 2 in " Inserting the CD-ROM"...
Page 39: Workflow
PRIMERGY RX300 S3 User’s Guide 1.5 Workflow Use the following workflow from server installation to start of operation. Installing the server Refer to "Safety Precautions" and "Start Guide" to install the server to a suitable place. Preparing the server - Install hardware options - Set hardware Refer to "2.1 Preparation on the server", "Chapter 7 Installing Internal Options"...
Page 40 Chapter1 Overview...
Page 41 Chapter 2 Checking before OS Installation This chapter explains the preparation on the server and cautions necessary before OS installation. Please read this chapter before starting installation. 2.1 Preparation on the Server ......2.2 Selecting the Installation Method .
Page 42: Chapter 2 Checking Before Os Installation
Chapter 2 Checking before OS Installation 2.1 Preparation on the Server Before starting installation, install internal options to the server and perform necessary hardware settings. 2.1.1 Installing Internal Options Internal options are classified into those that must be installed before the OS installation and those that must be installed after the OS installation.
Page 43 PRIMERGY RX300 S3 User’s Guide ■ Cautions for Installing a Memory Module This server supports up to 8GB of memory. However, the maximum installable size varies depending on the OS. Furthermore, since the server uses part of the memory as PCI resources, the maximum available size is limited.
Page 44: Hardware Settings
Chapter 2 Checking before OS Installation 2.1.2 Hardware Settings Before starting installation, set necessary hardware, such as the BIOS Setup Utility. ■ BIOS Setup Utility The BIOS Setup Utility must be set in the following cases. For details on how to set the BIOS Setup Utility, refer to "8.1 BIOS Setup Utility"...
Page 45 PRIMERGY RX300 S3 User’s Guide Check the MAC address. Start up the server from the network. The MAC address is displayed as shown below. CLIENT MAC ADDR: XX XX XX XX XX XX The MAC address is required for remote installation. Write it down.
Page 46: Selecting The Installation Method
To set up multiple servers with the same model and configuration, refer to "3.5 Installation on Multiple (the Second and Subsequent) Servers" ( pg.106). Linux For the use of Linux, refer to the Fujitsu PRIMERGY What OS will you use? website (http://primergy.fujitsu.com).
Page 47: Precautions On Installation
PRIMERGY RX300 S3 User’s Guide 2.3 Precautions on Installation Read the following notes before starting OS installation. 2.3.1 Installation Partition Size For installation using ServerStart, the installation partition size can be set as follows, depending on the OS to be installed and format.
Page 48: Notes On A Multiple Lan Adapter Configuration
Chapter 2 Checking before OS Installation ● Hardware Configuration • Only internal hard disk units can be used. • Be sure to use hard disk units of the same model and with the same capacity. ■ Notes • When a RAID-configured disk is used Hard disk units that have been used before may have unwanted partition information or array configuration information, which may cause unexpected problems.
Page 49 PRIMERGY RX300 S3 User’s Guide ■ Ejecting the CD-ROM Do not eject the ServerStart CD-ROM while ServerStart is running. If the ServerStart CD-ROM is ejected and inserted again, ServerStart starts up in multiple windows, and settings you have made can be lost.
Page 50: Expansion Cards Supported By Serverstart
Chapter 2 Checking before OS Installation 2.3.6 Expansion Cards Supported by ServerStart ServerStart supports automatic driver installation for the following expansion cards. table: Automatic Expansion Card Driver Installation Name Model Onboard FDD/IDE －－ SCSI array controller card PCI-X PG-142E3 Onboard LAN PCI-E －...
Page 51: Preparation For Using Serverstart On A Client Computer
PRIMERGY RX300 S3 User’s Guide 2.4 Preparation for Using ServerStart on a Client Computer When using the preconfiguration mode for setting installation information in advance or when creating a driver disk using the FloppyBuilder function, install ServerStart on the client computer.
Page 52 Chapter 2 Checking before OS Installation Click [OK]. The Windows installer starts and the setup window appears. Click [Next]. The [License Agreement] window appears. Select [I accept the license agreement] and click [Next]. The [User Information] window appears. Enter the user information of the software and click [Next]. The [Destination Folder] window appears.
Page 53 PRIMERGY RX300 S3 User’s Guide Disable [ServerStart - remote installation] and click [Next]. The [Ready to Install the Application] window appears. Specify whether or not to copy the contents of the CD. When you select [Yes] for "enable the use of ServerStart without CD.", you can start the preconfiguration mode on the client computer without using the CD-ROM.
Page 54: Uninstalling Serverstart
Select [Fujitsu ServerStart] and click [Remove] (or [Modify]). When the uninstallation is executed successfully, Fujitsu ServerStart is deleted. If [ServerStart - remote installation] has been installed using ServerStart, "FjPXEServer" seems undeleted. Leave it and complete the operation.
Page 55 Chapter 3 OS Installation Using ServerStart This chapter explains how to install the OS in the server using ServerStart. 3.1 Guided Mode ....... . . 3.2 Preconfiguration Mode .
Page 56: Chapter 3 Os Installation Using Serverstart
Chapter 3 OS Installation Using ServerStart 3.1 Guided Mode In guided mode, follow the wizard to specify hardware configuration and the OS to be installed, save the information necessary for installation in a configuration file, and install the OS. 3.1.1 Starting Up the Guided Mode Start up the guided mode.
Page 57 PRIMERGY RX300 S3 User’s Guide Click [OK]. The [Initialization of ServerStart core running] window appears and the ServerStart initialization process starts. Depending on the hardware configuration, this process may take a few minutes. When the process is completed, the [Create a ServerStart Floppy Disk] window appears.
Page 58 Chapter 3 OS Installation Using ServerStart Select your keyboard language from the drop-down list and click [OK]. The subsequent start procedure may take several minutes. The [Welcome to ServerStart] window appears. Click [Click here to prepare and/or initiate an operating system installation]. The [Select the operating system to be installed] window appears.
Page 59 PRIMERGY RX300 S3 User’s Guide Click [Prepare & initiate an unattended installation of (OS)]. The guided mode for the selected OS starts up. Start up the wizards to set items in the following procedures. Exiting the wizard returns the display to the guided mode window.
Page 60: Open/Create A Configuration File
Chapter 3 OS Installation Using ServerStart 3.1.2 Open/create a Configuration File Open a configuration file. Or create a new one. Click [Start here to create a complete configuration file]. The [Open ServerStart Configuration File] window appears. Once a configuration file is opened, another file cannot be opened until you click [Close and save Configuration File].
Page 61: Raid And Disk Wizard
PRIMERGY RX300 S3 User’s Guide 3.1.3 RAID and Disk Wizard Configure RAID, and create and format hard disk partitions. Click [RAID and Disk Wizard: RAID configuration and hard disk pertitioning / formatting]. The [Configuration for Disks and RAID Controllers] window appears.
Page 62 Chapter 3 OS Installation Using ServerStart ■ Installation While Maintaining the Established RAID Environment Select [Logical Drive View] on the [Configuration for Disks and RAID Controllers] window. Add a partition 1. Click [Add Partition]. A partition is added. Add required partitions. 2.
Page 63 PRIMERGY RX300 S3 User’s Guide ■ Configuring RAID Select [Mass Storage Controller View] on the [Configuration for Disks and RAID Controllers] window. Click [Details]. As the default values are configured, confirm the settings and modify them as necessary. Add partitions as necessary.
Page 64 Chapter 3 OS Installation Using ServerStart Add a partition 1. Click [Add Partition]. A partition is added. Add required partitions. 2. Click [Details] and modify the settings as necessary. The partition configuration is displayed. As the default values are configured, confirm the settings and modify them as necessary.
Page 65: Os Installation Wizard
PRIMERGY RX300 S3 User’s Guide 3.1.4 OS Installation Wizard Set computer information, user information, and the network protocol. ServerStart can configure multiple network patterns. When configuring a domain controller, refer to "Using ServerStart to Configure the Network". The setup window differs depending on the OS to be installed. The following describes operations on Windows Server 2003 R2.
Page 66 Chapter 3 OS Installation Using ServerStart Set items and click [Next]. When using the CD-ROM applied Service Pack 1 on Windows Server 2003, select the [(OS) including SP1] menu from the [Operating System Type] list. The [Installation Directory and Time Zone] window appears. Set items and click [Next].
Page 67 PRIMERGY RX300 S3 User’s Guide Set items and click [Next]. The [Network Protocol] window appears.
Page 68 Chapter 3 OS Installation Using ServerStart Set items and click [Next]. The [Software Components] window appears.
Page 69 PRIMERGY RX300 S3 User’s Guide If Windows Server 2003 R2 is selected at the Computer Identification, R2 components are always copied to the hard disk. To install the components, click [Properties] and check the components to be installed. Set items and click [Next].
Page 70: Application Wizard
[>>]. Set all applications to be installed on the [Selected applications] list. Fujitsu ServerView, Broadcom Advanced Control Suite (BACS), and RAID Management Tool are always installed in guided mode. In expert mode, the selection can be released. Click [leave wizard].
Page 71: Close/Save The Configuration File
PRIMERGY RX300 S3 User’s Guide 3.1.6 Close/save the Configuration File When settings in all wizards are completed, save the configuration file. Click [Close and save Configuration File]. The [Save ServerStart Configuration File] window appears. Click [Save As]. The configuration file is saved.
Page 72 Chapter 3 OS Installation Using ServerStart Click [Start now]. Clicking [Start now] deletes all disk contents and starts installation. Click [Stop] when you do not perform installation. After 10 seconds, installation starts automatically. 1. When RAID has been configured, the system restarts. 2.
Page 73 PRIMERGY RX300 S3 User’s Guide When the system restarts, log on to the server using the Administrator account for the local computer. The server setup and OS installation have been completed. Refer to "Chapter 5 Operations after OS Installation" ( pg.135) and perform necessary procedures...
Page 74: Preconfiguration Mode
If the contents of the ServerStart CD-ROM have been copied to the computer 1. Click [Start] → [Programs] → [Fujitsu ServerStart] → [ServerStart]. ServerStart starts up and the [Welcome to ServerStart] window appears. If the contents of the ServerStart CD-ROM have not been copied to the computer 1.
Page 75 PRIMERGY RX300 S3 User’s Guide Click [FloppyBuilder]. The [ServerStart FloppyBuilder] window appears. Click [ServerStart Status Diskette]. A message prompts you to insert the floppy disk. Insert the ServerStart floppy disk supplied with the server and click [OK]. Set the ServerStart floppy disk in the write-enabled state.
Page 76 Chapter 3 OS Installation Using ServerStart Select the OS to be installed. The [Preparing the Installation] window appears.
Page 77: Configure Settings In Wizards
PRIMERGY RX300 S3 User’s Guide 3.2.2 Configure Settings in Wizards Click the wizards to set items in the following procedures. For setting procedures, refer to description on guided mode wizards ("3.1.2 Open/create a Configuration File" ( pg.60) to "3.1.5 Application Wizard"...
Page 78: Close/Save The Configuration File
Chapter 3 OS Installation Using ServerStart 3.2.3 Close/save the Configuration File When settings in all wizards are completed, save the configuration file. Click [Close and save Configuration File]. The [Save ServerStart Configuration File] window appears. Click [Save As]. The [ServerStart Session IP Settings] window appears. Set items when performing remote installation.
Page 79: Starting Os Installation
PRIMERGY RX300 S3 User’s Guide 3.2.4 Starting OS Installation Install the OS to the server using the created configuration file. During installation, do not use the mouse or keyboard unless it is necessary for installation operations. Otherwise, installation may fail.
Page 80 Chapter 3 OS Installation Using ServerStart 4. If a message prompts you to insert the Service Pack CD-ROM, insert the CD-ROM and click [OK]. This message does not appear when Service Pack is not selected. 5. For Windows Server 2003 x64, a message prompts you to insert the ServerStart Disc 2 and restart the system.
Page 81: Expert Mode
PRIMERGY RX300 S3 User’s Guide 3.3 Expert Mode In expert mode, start up Disk Manager, format the installation partition, and install the Use the expert mode only when you want to perform installation while maintaining the existing partitions. Use the guided mode for normal installation.
Page 82 Chapter 3 OS Installation Using ServerStart Select the OS to install. Click [Install MS Windows Server 2003 interactively (expertise required)]. The expert mode starts. Start up the configuration tools to set items in the following procedures. Exiting a tool returns to the display to the expert mode window.
Page 83: Disk Manager
PRIMERGY RX300 S3 User’s Guide 3.3.2 Disk Manager Start up Disk Manager and format the installation partition. Click [Use Disk Manager to partition and format your disk drives]. Disk Manager starts up. Format the OS installation partition. Select the OS installation partition and click the [Partition] menu →...
Page 84: Os Installation Wizard
Chapter 3 OS Installation Using ServerStart 3.3.3 OS Installation Wizard Set computer information, user information, and the network protocol. ServerStart can configure multiple network patterns. When configuring a domain controller, refer to "Using ServerStart to Configure the Network". The setting window differs depending on the OS to be installed. The following describes operations on Windows Server 2003 R2.
Page 85: Application Wizard
PRIMERGY RX300 S3 User’s Guide Set items and click [Next]. The [Software Components] window appears. If Windows Server 2003 R2 is selected at the Computer Identification, R2 components are always copied to the hard disk. To install the components, click [Properties] and check the components to be installed.
Page 86 Chapter 3 OS Installation Using ServerStart Click [Yes]. The following window appears. Enter the file name and click [Save As]. Installation starts automatically. 1. If a message prompts you to insert the Array Controller Document & Tool CD, insert the CD-ROM and click [OK]. 2.
Page 87 PRIMERGY RX300 S3 User’s Guide When a message prompts you to insert the OS CD-ROM, insert the CD-ROM and click [OK]. For Windows 2000 / Windows Server 2003 / Windows Server 2003 x64 Insert the OS CD-ROM (Installation CD-ROM). For Windows Server 2003 R2 / Windows Server 2003 R2 x64 Insert the OS CD-ROM (Installation CD-ROM) Disc 1.
Page 88: Remote Installation
Chapter 3 OS Installation Using ServerStart 3.4 Remote Installation ServerStart supports remote installation. Before performing remote installation, be sure to read "Cautions for Remote Installation" in the online help. 3.4.1 Overview of Remote Installation Remote installation is a method to save resources necessary for installation, such as the OS and Service Pack, in a different server on the network and install them via the network.
Page 89 PRIMERGY RX300 S3 User’s Guide ● Remote Installation Using a Remote Resource Server In remote installation using a remote resource server, ServerStart starts up on the target server. Procedures for starting installation are the same as those in normal installation (preconfiguration, guided, and expert modes).
Page 90 Chapter 3 OS Installation Using ServerStart ■ Checking Server Free Space Decide a server to use as a remote resource server / PXE server and check it for enough free space for storing resources. ● Checking the Number of Servers •...
Page 91: Preparation Of The Pxe Server (When The Pxe Server Is Used)
PRIMERGY RX300 S3 User’s Guide 3.4.2 Preparation of the PXE Server (When the PXE Server is Used) When performing remote installation using a PXE server, preparatory procedures, such as installing ServerStart, are required. Perform the following procedures to prepare the PXE server.
Page 92 Chapter 3 OS Installation Using ServerStart ■ Installing ServerStart Insert the ServerStart Disc 1 CD-ROM into the PXE server. The [ServerStart Launcher] window appears. When the [ServerStart Launcher] window does not appear, execute "Launcher.exe" in the CD- ROM. Click [OK]. The Windows installer starts and the Setup window appears.
Page 93 PRIMERGY RX300 S3 User’s Guide Select the installation folder and click [Next]. To change the installation folder, click [Browse] and select the folder. The [Select Features] window appears. Configure [ServerStart - remote installation] so that it will be installed. To install Windows Server 2003 x64, configure [Microsoft Windows Server x64 Edition -Remote install] as well.
Page 94 Chapter 3 OS Installation Using ServerStart Click [Next]. The [contents tree] window appears. Configure the ServerStart image necessary for network startup (PXE) and click [Next]. The [Useraccount for access to the content tree] window appears.
Page 95 PRIMERGY RX300 S3 User’s Guide Specify the user account for the content tree and click [Next]. The [PXE server] window appears. Select [yes] when the PXE server performs the DHCP service or select [no] when the DHCP and PXE servers are configured separately. Then click [Next].
Page 96 Chapter 3 OS Installation Using ServerStart Click [show Readme file]. The [Readme] window appears. Read the text. When you finish, click [ ] in the upper-right corner of the window to close the [Readme] window. Click [Next]. The image file is copied. The image file copying process takes about 10 to 20 minutes.
Page 97 Guest account to obtain the image via network startup (PXE). Click [Start] → [Programs] → [Accessories] → [Windows Explorer] and move to the TFTP path (the default is C:\Program Files\Fujitsu Siemens\DeploymentService\tftp). Right-click the TFTP folder and click [Properties].
Page 98: Preparation Of Remote Resources
Chapter 3 OS Installation Using ServerStart Click the [Security] tab, add the Guest account, and set the "Read and execute", "View folder contents list", and "Read" access permissions. The preparation of the PXE server has been completed. Then, perform "3.4.3 Preparation of Remote Resources" ( pg.98). 3.4.3 Preparation of Remote Resources Store resources to be installed on the remote resource server (PXE server) before starting installation.
Page 99: Starting Remote Installation Using A Pxe Server
PRIMERGY RX300 S3 User’s Guide 3.4.4 Starting Remote Installation Using a PXE Server Perform remote installation using a PXE server in the following procedures. Checking the Network Startup (PXE) Setting Checking the MAC Address Creating a Configuration File (Setting of remote installation) Starting remote Installation ■...
Page 100 On the PXE server, start up ServerStart. If ServerStart has already been started, you do not have to restart it. If it is not started, click [Start] → [Programs] → [Fujitsu ServerStart] → [ServerStart]. The [Welcome to ServerStart] window appears.
Page 101 PRIMERGY RX300 S3 User’s Guide Configure remote installation. 1. Enter the "MAC address of target system". 2. Select the "PRIMERGY model type". 3. Specify the "Configuration File" containing the installation settings. Click [Start Installation]. Installation starts. All disk contents on the target server are deleted.
Page 102: Starting Remote Installation Using A Remote Resource Server
Chapter 3 OS Installation Using ServerStart Turn on the target server. It is started up via the network (PXE) and installation starts. When the resources have been copied, the "Preparation for automatic OS installation has completed." message appears. Subsequent installation is performed automatically. When the installation is completed, an installation completion message appears on the target server.
Page 103 PRIMERGY RX300 S3 User’s Guide ■ Checking Remote Resources Check that the remote resource server is shared properly. Start up "Command Prompt" on the remote resource server. Enter the following and press the [Enter] key. prompt:>net share Check that the created shared folder is displayed properly.
Page 104 Chapter 3 OS Installation Using ServerStart Click [MS Windows Operating Systems]. The [Install Microsoft Windows Operating System Installation] window appears. Select the OS to install and the mode. Set items in wizards and save the configuration file. For settings in wizards, refer to "3.1 Guided Mode" ( pg.56) or "3.3 Expert Mode" ( pg.81). Set items in wizards and save the configuration file.
Page 105 PRIMERGY RX300 S3 User’s Guide Click [Start]. Installation starts. At steps where the CD-ROM for resources such as the OS to be installed is necessary, the resource is automatically acquired from the resource server via the network. Eject the CD-ROM and floppy disk and click [OK].
Page 106: Installation On Multiple (The Second And Subsequent) Servers
Chapter 3 OS Installation Using ServerStart 3.5 Installation on Multiple (the Second and Subsequent) Servers This chapter explains how to perform installation on multiple servers using ServerStart. By editing the configuration file created for installation on the first server, you can use it for installation on other servers of the same model and configuration.
Page 107: Installation In Guided Mode
PRIMERGY RX300 S3 User’s Guide 3.5.2 Installation in Guided Mode Edit the configuration file and perform installation in guided mode. Turn on the server and insert the ServerStart Disc 1 CD-ROM immediately after that. ServerStart starts up and a message prompts you to insert the ServerStart floppy disk.
Page 108: Installation In Preconfiguration Mode
When the CD has been copied on Windows 2000 Professional/Windows XP Professional 1. Click [Start] → [Programs] → [Fujitsu ServerStart] → [ServerStart]. ServerStart starts up and the [Welcome to ServerStart] window appears. When Windows NT is used or CD has not been copied 1.
Page 109 PRIMERGY RX300 S3 User’s Guide Insert the ServerStart floppy disk copied in the preparatory procedure into the floppy disk drive and click [Start here to configuration file]. The [Open ServerStart Configuration File] window appears. Specify "SerStartBatch.ini" on drive A and click [Create].
Page 110 Chapter 3 OS Installation Using ServerStart...
Page 111: Chapter 4 Manual Os Installation
Chapter 4 Manual OS Installation This chapter explains how to install the OS without using ServerStart. 4.1 Creating Driver Disks ......112 4.2 Starting Manual Installation .
Page 112: Creating Driver Disks
Onboard arry controller MegaRAID SAS Driver Windows 2003 for x64 Edition Drivers Disk V1.18L10 Onboard LAN PRIMERGY RX300 S3/RX300W S3 Onboard LAN Driver Windows 2003 for x64 Edition Drivers Disk PG-185x/186x/188x/189x LAN Driver Windows 2003 for x64 LAN card (PG-1862 / PG-1882(L) / PG-1892(L)) Edition Drivers Disk Ver10.1...
Page 113 Driver provided with the Server Start CD-ROM Onboard arry controller MegaRAID SAS Driver Windows 2000/2003 Drivers Disk V1.18L10 Onboard LAN PRIMERGY RX300 S3/RX300W S3 Onboard LAN Driver Windows 2000/2003 Drivers Disk PG-185x/186x/188x/189x LAN Driver Windows 2000/2003 LAN card (PG-1862 / PG-1882(L) / PG-1892(L)) Drivers Disk Ver10.1...
Page 114: How To Create Driver Disks [Floppybuilder Function]
● For Creation on a Client Computer When the CD has been copied Click [Start] → [Programs] → [Fujitsu ServerStart] → [ServerStart]. ServerStart starts up and the [Welcome to ServerStart] window appears. When the CD has not been copied Insert the ServerStart Disc 1 CD-ROM into the client computer.
Page 115 PRIMERGY RX300 S3 User’s Guide ● For Creation on the Server Turn on the server and insert the ServerStart Disc 1 CD-ROM immediately. ServerStart starts up and a message prompts you to insert the ServerStart floppy disk. Insert the attached [ServerStart floppy disk] into the server's floppy disk drive.
Page 116 Chapter 4 Manual OS Installation ■ Creating Driver Disks Start up ServerStart and confirm that the [Welcome to ServerStart] window is displayed. Click [FloppyBuilder]. The [ServerStart FloppyBuilder] window appears. Select the Drivers Diskettes for Windows Server 2003 / Windows 2000 Server or Windows Server 2003 x64.
Page 117: Starting Manual Installation
PRIMERGY RX300 S3 User’s Guide 4.2 Starting Manual Installation This section explains the procedures for installing the OS manually. 4.2.1 Installing Windows Server 2003 x64 For details on the OS settings, refer to the following URL. http://www.microsoft.com/technet/prodtechnol/exchange/2003/Library/default.mspx Create driver disks.
Page 118 Chapter 4 Manual OS Installation Install the Drivers for onboard array controller manually. 1. When the following message appears, press the [S] key. To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows, including those for which you have a devicesupport disk from a mass storage device manufacturer, press S.
Page 119: Installing Windows Server 2003
PRIMERGY RX300 S3 User’s Guide 3. Click [Next]. Follow the instructions in the window to perform installation. 4. When the "InstallShieled(R) wizard has completed" message appears, eject the ServerStart CD-ROM from the CD-ROM drive and click [Finish] to restart the system.
Page 120 Chapter 4 Manual OS Installation Turned on the server and configure RAID. Turn on the server to display the following message and press the [Ctrl] + [H] key to start up the WebBIOS. Press <Ctrl><H> for WebBIOS The array system is configured by using WebBIOS. For more details, refer to the "MegaRAID SAS User’s Guide"...
Page 121 PRIMERGY RX300 S3 User’s Guide 5. Follow the instructions in the window to perform installation The message which prompts you to set the floppy disk appears during the installation, set the driver disk and push the [Enter] key. Follow the instructions from the setup program to continue the installation procedure.
Page 122: Installing Windows 2000 Server
Chapter 4 Manual OS Installation ● Before Starting Operation After OS installation, refer to "Chapter 5 Operations after OS Installation" ( pg.135) and perform the necessary procedures. 4.2.3 Installing Windows 2000 Server Create driver disks. Prepare necessary drivers before installing Windows 2000 Server. Some drivers used with Windows 2000 Server are created from the ServerStart CD-ROM.
Page 123 PRIMERGY RX300 S3 User’s Guide Install the Drivers for onboard arry controller manually. 1. When the following message appears, press the [S] key. To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows 2000, including those for which you have a device support disk from a mass storage device manufac- turer, press S.
Page 124 Chapter 4 Manual OS Installation 2. Execute the following command on the CD-ROM. [CD-ROM drive] :\DRIVERS\ChipSet\Intel\5000P\infinst_autol.exe The installation wizard starts up. 3. Click [Next]. Follow the instructions in the window to perform installation. 4. When the "InstallShieled(R) wizard has completed" message appears, eject the ServerStart CD-ROM from the CD-ROM drive and click [Finish] to restart the system.
Page 125: Installing Linux
The installation of Windows 2000 Server has completed. ● Before Starting Operation After OS installation, refer to "Chapter 5 Operations after OS Installation" ( pg.135) and perform the necessary procedures. 4.2.4 Installing Linux For the use of Linux, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).
Page 126: Installing The Lan Driver
Chapter 4 Manual OS Installation 4.3 Installing the LAN Driver This section explains the procedure for installing the driver. In addition to the case where the OS is installed manually, the driver must be installed when a LAN card is added. 4.3.1 Installing the LAN Driver (Windows Server 2003 x64) The LAN driver installation procedure differs depending on whether the network adapter was recognized during the OS installation.
Page 127 PRIMERGY RX300 S3 User’s Guide ● When a recognized network adapter is present ■ Perform " Updating the LAN Cards" ( pg.127) on the LAN device name under [Network adapters], ■ then " Installing the LAN Driver" ( pg.128) on [Ethernet controller] under [Other devices].
Page 128 Chapter 4 Manual OS Installation ■ Installing the LAN Driver Perform the following procedures on each [Ethernet controller] under [Other devices] in [Device Manager]. Insert the driver disk created from the ServerStart CD-ROM into the server. Double-click [Ethernet controller] under [Other devices]. The properties window for the Ethernet controller appears.
Page 129: Installing The Lan Driver (Windows Server 2003 )
PRIMERGY RX300 S3 User’s Guide 4.3.2 Installing the LAN Driver (Windows Server 2003 ) The LAN driver installation procedure differs depending on whether the network adapter was recognized during the OS installation. For the following LAN card, the network adapter is recognized when the card is mounted during OS installation.
Page 130 Chapter 4 Manual OS Installation When the LAN driver is installed to [Other devices] before updating the driver for the network adapter recognized immediately after the OS installation When driver installation starts, the following window appears. Clicking [Finish] displays the [Help and Support Center] window. Click [X] to close the window. After installation, the "!"...
Page 131 PRIMERGY RX300 S3 User’s Guide ■ Installing the LAN Driver Perform the following procedures on each [Ethernet controller] under [Other devices] in [Device Manager]. Insert the driver disk created from the ServerStart CD-ROM into the server. For the onboard LAN, insert the ServerStart CD-ROM.
Page 132: Installing The Lan Driver (Windows 2000 Server)
Chapter 4 Manual OS Installation 4.3.3 Installing the LAN Driver (Windows 2000 Server) Insert the driver disk created from the ServerStart CD-ROM into the server. Right-click the [My Computer] icon on the desktop and select [Manage] from the displayed menu. Click [Device Manager].
Page 133: Latest Drivers
Intel(R) PRO/1000 MT Dual Port Server Adapter PG-1882(L) Intel(R) PRO/1000 MF Server Adapter PG-1892(L) Intel(R) PRO/1000 MT Server Adapter PG-2861L Intel(R) PRO1000 PT Dual Port Server Adapter 4.3.4 Latest Drivers For the latest drivers, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).
Page 134 Chapter 4 Manual OS Installation...
Page 135 Chapter 5 Operations after OS Installation This chapter explains the operations to be performed after OS installation. Be sure to perform these operations before operating the server. 5.1 Memory Dump/Paging File Setting ....136 5.2 Creating a Disk for System Recovery .
Page 136: Chapter 5 Operations After Os Installation
Chapter 5 Operations after OS Installation 5.1 Memory Dump/Paging File Setting Before starting operating this server, configure the setting for obtaining memory dump. The setting procedure varies between Windows Server 2003 and Windows 2000 Server. ● Memory Dump If memory dump is set, debugging information will be automatically saved when a STOP error (fatal system error) occurs in the system.
Page 137 PRIMERGY RX300 S3 User’s Guide ● Kernel Memory Dump Information of only kernel memory space is recorded. The file is stored in the directory displayed in the [Dump file] box. Capacity required for kernel memory dump is as follows: • Paging file: Depending on installed physical memory amount For memory of 256 to 1,373MB - Installed physical memory x 1.5...
Page 138 Chapter 5 Operations after OS Installation Click the [Advanced] tab and click [Settings] in [Startup and Recovery]. The [Startup and Recovery] window appears. Set as follows: 1. In the [Write debugging information] section, select the memory dump file type. • Complete memory dump (Recommended) The whole system memory information is recorded to the memory dump file.
Page 139 PRIMERGY RX300 S3 User’s Guide ■ Paging File Setting Set up the paging file according to the following procedures: Log on to the server with administrator privileges. Check free space of the drive where the system is installed. ■ Check the required amount of free space according to "...
Page 140 Chapter 5 Operations after OS Installation Click [Change] in the [Virtual memory] section. The [Virtual Memory] window appears. Specify the drive where the paging file is to be created. In [Drive], select the drive where the system is installed. The selected drive is displayed in [Drive] in [Paging file size for selected drive]. Select [Custom size] and enter a value in [Initial size].
Page 141: How To Obtain Memory Dump For Windows 2000 Server
PRIMERGY RX300 S3 User’s Guide Restart the system. The setting is enabled after the system is restarted. 5.1.2 How to Obtain Memory Dump for Windows 2000 Server Check the following settings before starting configuration to obtain memory dump. ■ Checking Hard Disk Free Space Once memory dump is obtained, a file containing contents of the whole physical memory installed in the system is created.
Page 142 Chapter 5 Operations after OS Installation ● Small Memory Dump Minimum amount of useful information for problem identification is recorded. In this option, a paging file of at least 2MB is required in the boot volume. Also, a new file is created each time the system unexpectedly stops.
Page 143 PRIMERGY RX300 S3 User’s Guide Set as follows: 1. In the [Write debugging information] section, select the memory dump file type. • Complete memory dump (Recommended) The whole system memory information is recorded to the memory dump file. • Kernel memory dump Only kernel memory is recorded to the memory dump file.
Page 144 Chapter 5 Operations after OS Installation Click the [Advanced] tab and click [Performance Options]. The [Performance Options] window appears. Click [Change] in the [Virtual memory] section. The [Virtual Memory] window appears. Specify the drive where the paging file is to be created. In [Drive], select the drive where the system is installed.
Page 145 PRIMERGY RX300 S3 User’s Guide Save the settings. Click [Set] in the [Paging file size for selected drive] section. The settings are saved, and the value specified is displayed in [Paging File Size] of [Drive]. Click [OK] to close the [Virtual Memory] window.
Page 146: Creating A Disk For System Recovery
Chapter 5 Operations after OS Installation 5.2 Creating a Disk for System Recovery If the installation of the OS was performed manually, create a system recovery disk. If the system file, system configuration or environment setting change at startup, etc., are damaged, such data can be reconstructed using the recovery information stored in the created system recovery disk.
Page 147: Creating A System Recovery Disk For Windows 2000 Server
PRIMERGY RX300 S3 User’s Guide When the process is completed, a message appears. Eject the floppy disk according to the message and put a label on it. Label Example: "Windows Automated System Recovery Disk: Backup.bkf, Created at 12:00 04/ 01/2003"...
Page 148: Storing The System Configuration Information
Chapter 5 Operations after OS Installation 5.3 Storing the System Configuration Information Before starting operations, store the configuration information of the BIOS Setup Utility. By storing this information, the system can be recovered with the stored information in case of a system failure (such as when the information is deleted due to the drain of the built-in battery).
Page 149: Storing The Bios Information
PRIMERGY RX300 S3 User’s Guide 5.3.1 Storing the BIOS Information Store the BIOS information according to the following procedures. Before starting the operation, if the "OS Boot Monitoring" function of ServerView is enabled, disable it (it is disabled by default).
Page 150: Recovering The Bios Information
Chapter 5 Operations after OS Installation 5.3.2 Recovering the BIOS Information If the information configured with the BIOS Setup Utility was deleted due to a drain of the built-in server battery, etc., restore the BIOS information according to the following procedures. Do not turn off the server during a program run.
Page 151: Creating Maintenance Tools
Types of a Hardware Configuration Tool vary by model. ■ Starting ServerStart ● For Creation on a Client Computer When the CD has been copied Click [Start] → [Programs] → [Fujitsu ServerStart] → [ServerStart]. ServerStart starts up and the [Welcome to ServerStart] window appears.
Page 152 Chapter 5 Operations after OS Installation When the CD has not been copied Insert the ServerStart Disc 1 CD-ROM into the client computer's CD-ROM drive. ServerStart starts up and the [Welcome to ServerStart] window appears. ● For Creation on the Server Turn on the server and insert the ServerStart Disc 1 CD-ROM immediately after that.
Page 153 PRIMERGY RX300 S3 User’s Guide Click [or Insert a ServerStart Floppy Disk to Start ServerStart]. The [Welcome to ServerStart] window appears. Eject the ServerStart floppy disk. ■ Creating a Hardware Configuration Tool Floppy Disk Start up ServerStart and confirm that the [Welcome to ServerStart] window is displayed.
Page 154: Creating A Dos Floppy Disk
Chapter 5 Operations after OS Installation Perform the subsequent operations according to the messages on the window. The floppy disk will be formatted automatically and file copying will start. The respective tools will be created automatically. When a message appears indicating that the disk is created, click [OK] and eject the disk.
Page 155: Notes Before Operating The Server
PRIMERGY RX300 S3 User’s Guide 5.5 Notes Before Operating the Server This section explains the settings required before starting to operate the server. For details on the settings, refer to the following URL. http://www.microsoft.com/technet/prodtechnol/exchange/2003/Library/default.mspx • If a LAN card was added, install a driver according to "4.3 Installing the LAN Driver" ( pg.126).
Page 156: Auto-Run Function From Cd-Rom Drives
Chapter 5 Operations after OS Installation 5.5.2 Auto-run Function from CD-ROM Drives Perform the following procedures to change the settings of the auto-run function from the CD-ROM drives after server installation: Make the registry editable, and change the value of AutoRun of the following registry key: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\CDRom Set the value of Autorun to "1"...
Page 157: Notes On Advanced Uninterruptible Power Supply (Ups)
5.5.5 Using the Fiber Channel Controller (PG-FC202) To use the Fiber Channel Controller (PG-FC202), the driver needs to be updated after installing the OS. You can used the driver supplied with the Fiber Channel Controller or download it from the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).
Page 158: Turning The Power On Via A Lan
Chapter 5 Operations after OS Installation 5.5.6 Turning the Power On via a LAN You can turn the power on the server from a client (via a LAN) by utilizing the Wakeup on LAN (WOL) function. Be sure to install ServerView to control the power supply via a LAN. When the power cable is disconnected from the server or the server is powered off due to power interruption, restart the server.
Page 159 PRIMERGY RX300 S3 User’s Guide ■ Notes on 24-hour Operation ● Automated System Operation To provide an extra margin of safety against unintentional damage, introduce disaster-prevention measures in the office and keep disaster prevention personnel (such as a security guard or janitor) in the building.
Page 160: Lan Driver Advanced Setup [Bacs]
Chapter 5 Operations after OS Installation 5.6 LAN Driver Advanced Setup [BACS] BACS is an integrated GUI application consisting of programs such as BASP (Broadcom Advanced Server Program) that provides the load balancing feature, etc., by teaming up multiple adapters. BACS is used in the following situations: •...
Page 161 PRIMERGY RX300 S3 User’s Guide Click [Next]. License agreement window appears. Click [I accept the terms in the license agreement] and click [Next]. Custom Set up window appears. Click [Install]. Click [OK]. Click [Finish].
Page 162: Load Balance
Chapter 5 Operations after OS Installation ■ For Windows Server 2003, Windows 2000 Server If the OS is installed using ServerStart, "BACS" is already installed with the driver. If the OS is installed manually, BACS will not be installed. Execute the following file contained in the ServerStart Disc 1 CD-ROM. [CD-ROM drive]: \PROGRAMS\GENERAL\Broadcom\MgmtApps\setup.exe The installer starts up.
Page 163 PRIMERGY RX300 S3 User’s Guide Click [Create a Team] from the [Tools] menu. Click [Expert Mode] form the [Welcome to the Broadcom Teaming Wizard] window.
Page 164 Chapter 5 Operations after OS Installation Specify [team name] and select [Team Type] in the [New Team Configuration] window. Do not select [Link Aggregation(802.3ad)] for the [Team Type]. Select an adapter to add to the created team from [Available adapters], click the [ ] and [ ] buttons, and move the adapter to [Load Balance Members]...
Page 165: Vlan Setup Procedure
PRIMERGY RX300 S3 User’s Guide Click [Apply] to apply the settings. After the network is temporarily disconnected, a window is displayed. Click [Yes (Y)]. When continuing to VLAN settings, go to "5.6.3 VLAN Setup Procedure" ( pg.165). 5.6.3 VLAN Setup Procedure Start up BACS.
Page 166 Chapter 5 Operations after OS Installation Specify [Team Name] , [VLAN ID] and [VLAN Name] in the [Create New VLAN] window. If you selected [Add VLAN] in step 2, the [Team Name] is not displayed. The [VLAN ID] should be identical with the switch setting. The [VLAN Name] does not need to be identical with the switch setting.
Page 167: Cautions On Using The Teaming (Slb (Auto-Fallback Disable)) Function
PRIMERGY RX300 S3 User’s Guide 5.6.4 Cautions on Using the Teaming (SLB (Auto-Fallback Disable)) Function When a primary adapter is recovered from a failure during standby operation, auto-fallback is not performed for the primary adapter. Communication is continued with the standby adapter.
Page 168: Cautions For Onboard Lan Driver
Chapter 5 Operations after OS Installation Select the Team name of the Teamed Up adapter, and click [Fallback] from the [Team Properties] tab in the right pane of the window. Confirm that the mark moved from the standby adapter to the primary adapter and communication is maintained.
Page 169: Lan Driver Advanced Setup [Intel® Proset]
PRIMERGY RX300 S3 User’s Guide 5.7 LAN Driver Advanced Setup ® [Intel PROSet] ® "Intel PROSet" is a tool for configuring details on the LAN driver. This is used in the following cases. • Use the Teaming function between LAN cards or between a LAN card and the onboard LAN •...
Page 170: Cautions For Pg-185X/186X/188X/189X/286X Lan Driver V10.1
Chapter 5 Operations after OS Installation 5.7.2 Cautions for PG-185x/186x/188x/189x/286x LAN Driver V10.1 ■ Event Log Once a Team is setup, multiple identical logs from the same source that starts with the following log may be stored in the system log file of the event viewer at system start-up. Source iANSMiniport Type...
Page 171 PRIMERGY RX300 S3 User’s Guide • The team cannot be configured with only Broadcom onboard LANs. It is necessary to incorporate in Intel LAN card more than one port. • Make sure to set any port of the Intel LAN card as [Set Primary]. To configure it, click the [Settings] tab and [Modify Team...], select the LAN card, and click [Set Primary].
Page 172: Vlan
Chapter 5 Operations after OS Installation Click [OK] to close the property window for the LAN adapter. When the Teaming setting is completed, the following virtual adapter will be created. • "Team:(Team Name)" Upper protocols will be bound with the main virtual adapter. You cannot bind them with the LAN card consisting of a Team.
Page 173: Chapter 6 High Reliability Tools
Chapter 6 High Reliability Tools For stable PRIMERGY server operations, we recommend that high reliability tools be installed. This chapter explains the installation and necessary settings of high reliability tools. 6.1 RAID Management Tool [Global Array Manager] ..174 6.2 Server Monitoring Tool [ServerView] .
Page 174: Raid Management Tool [Global Array Manager]
Chapter 6 High Reliability Tools 6.1 RAID Management Tool [Global Array Manager] RAID Management Tool is software that performs array configuration, disk initialization and disk array monitoring. For more details, refer to "MegaRAID SAS User’s Guide" of the Array Controller Document & Tool CD. OS installation using ServerStart If the OS is installed using ServerStart, RAID Management Tool is installed with the OS and other high reliability tools.
Page 175: Server Monitoring Tool [Serverview]
PRIMERGY RX300 S3 User’s Guide 6.2 Server Monitoring Tool [ServerView] ServerView constantly monitors the status of the servers' hardware in the network and provides a console with which the administrator can check the status of all the servers at a glance. When using ServerView, the server hardware is monitored all the time.
Page 176: Installing Serverview
Chapter 6 High Reliability Tools ● Power Supply Monitoring ServerView monitors the power supply. In an environment where ServerView is not applied, power supply irregularities cannot be detected during operation. In order to detect the problem, the server must reboot to run the BIOS Setup Utility or the Server Management Tools. System stops due to power supply failures cannot be prevented.
Page 177: Solving Problems Early [Dsnap]
PRIMERGY RX300 S3 User’s Guide 6.3 Solving Problems Early [DSNAP] DSNAP is a tool for collectively acquiring failure investigation information such as server environment information. OS installation using ServerStart If the OS is installed using ServerStart, DSNAP is installed with the OS and other high reliability tools.
Page 178 Chapter 6 High Reliability Tools...
Page 179 Chapter 7 Installing Internal Options This chapter explains how to install internal options on this server. 7.1 Before Installing Internal Options ....180 7.2 Installing/Removing the Top Cover .
Page 180: Chapter 7 Installing Internal Options
Chapter 7 Installing Internal Options 7.1 Before Installing Internal Options The following types of internal options can be installed on this server. Intenal 3.5-inch option Expansion card Memory module " With basic card slot conversion kit " Power supply unit When re-installing internal options, make sure to use the removed screws for the same device at the same location where it was last installed.
Page 181 PRIMERGY RX300 S3 User's Guide • Before installing/removing internal options to/from the server, turn off the server, all peripheral devices, and any other connected devices. Also unplug all power cables from the server. Failure to do so may cause electric shock ( "1.4.3 Turning Off the Server"...
Page 182: Installing/Removing The Top Cover
Chapter 7 Installing Internal Options 7.2 Installing/Removing the Top Cover When installing internal options, remove the top cover. See below how to remove the top cover. • Before installing/removing the top cover, turn off the server and all peripheral devices. Also unplug all power cables from the server ( "1.4.3 Turning Off the Server"...
Page 183 PRIMERGY RX300 S3 User's Guide Slide out the server. Hold the handle and slide out the server until it clicks, and the server is locked on the rail on both sides. Lock Handles • Be careful not to pinch fingers or clothes when sliding out the server or pushing it back.
Page 184: Installing The Cpu
Chapter 7 Installing Internal Options 7.3 Installing the CPU Up to two CPUs can be installed on this server by installing an optional CPU. • Before installing/removing the CPU, turn off the server and all peripheral devices. Also unplug all power cables from the server ( "1.4.3 Turning Off the Server"...
Page 185: Installable Cpus And Notes
PRIMERGY RX300 S3 User's Guide 7.3.2 Installable CPUs and Notes ■ Installable CPUs The following types of CPUs can be installed on this server. When installing an optional CPU, the two CPUs must have the same product name (same frequency/cache size).
Page 186 Chapter 7 Installing Internal Options Remove the CPU dummy that is installed in CPU socket 2. Slightly tilt the CPU dummy to unhook it (4 places), and remove it. Slightly tilt to remove the hook CPU dummy Remove the socket protection cover. Socket protection cover Open the socket cover.
Page 187 PRIMERGY RX300 S3 User's Guide Install the CPU. 1. Align the No.1 pin mark (a small triangle) of the CPU socket with the triangle mark of the CPU, and install the CPU. 2. Close the socket cover to secure the CPU to the CPU socket.
Page 188: Defective Cpu Disconnection Function
Chapter 7 Installing Internal Options Initialize the Extended System Configuration Data (ESCD). Set [Reset Configuration Data] to [Yes] in the Advanced menu of the BIOS Setup Utility. See "Reset Configuration Data" in "8.1.5 The Advanced Menu" ( pg.235). Save the BIOS configuration data. "5.3 Storing the System Configuration Information"...
Page 189: Installing Memory Modules
PRIMERGY RX300 S3 User's Guide 7.4 Installing Memory Modules Additional memory modules will help increase the amount of data that can be read at a time and improve the server processing capability. • Before installing or removing memory modules, turn off the server and all peripheral devices.
Page 190: Installation Locations And Order Of Memory Modules
Chapter 7 Installing Internal Options 7.4.1 Installation Locations and Order of Memory Modules Install memory modules in the memory slots on the baseboard. Memory Pair 1 Memory Pair 3 Memory Pair 2 Memory Pair 4 Front ■ Installation Order Install the memory modules in this order: memory pair 1 → memory pair 2 → memory pair 3 → memory pair 4.
Page 191 PRIMERGY RX300 S3 User's Guide ■ How to Identify a Memory Module When installing memory modules, make sure that the two memory modules (DIMMs) in each set have the same number beginning with "CA" (e.g. CA05946-E101) on their DIMM label.
Page 192: How To Install Or Remove Memory Modules
Chapter 7 Installing Internal Options Press the [F10] key. A message confirming whether to save the BIOS setting change is displayed. Select [Yes] and press the [Enter] key. After the system restarts, the memory mirror configuration becomes effective. 7.4.3 How to Install or Remove Memory Modules •...
Page 193 PRIMERGY RX300 S3 User's Guide Install memory modules. Insert the memory module vertically in the memory slot while fitting the concavity. When the memory module is properly installed, the levers on both sides of the slot are pulled back. At this time, confirm that the memory module is fixed. If the levers are not pulled back completely, make sure the levers are pushed inwards.
Page 194: Defective Memory Disconnection Function
Chapter 7 Installing Internal Options 7.4.4 Defective Memory Disconnection Function This server has a defective memory disconnection function. This function disconnects the memory block (two DIMMs) judged to be defective (causing an error) during Power On Self Test (POST) to start the server. When POST is executed, if the memory capacity is discovered to be smaller than the capacity of the memory installed, a memory module may be defective.
Page 195: Installing Expansion Cards
PRIMERGY RX300 S3 User's Guide 7.5 Installing Expansion Cards This section contains notes concerning types of expansion cards, various specific expansion cards, and how to install them. • Before installing an expansion card, turn off the server and all peripheral devices, and unplug the power cables from the outlet ( "1.4.3 Turning Off the...
Page 196: Installation Location Of Expansion Cards
Chapter 7 Installing Internal Options 7.5.1 Installation Location of Expansion Cards This server is equipped with five PCI slots, and a maximum of five expansion cards can be installed. If the server is equipped with the standard card slot conversion feature, a maximum of three expansion cards can be installed.
Page 197: Installable Expansion Cards And Notes
PRIMERGY RX300 S3 User's Guide ■ PCI Hot Plug (PHP) • PCI slot 3 and PCI slot 4 in this server support the PHP function. If an expansion card is defective, you can replace the defective expansion card without turning off the server and peripheral devices.
Page 198 Chapter 7 Installing Internal Options ● When Using the Standard Card Slot Conversion Feature table: Installable Expansion Cards Using the Standard Card Slot Convert Feature Installed card Model Remarks SCSI array controller card PG-142E3 Ultra320 SCSI 2ch, for optional external SCSI devices (incl.
Page 199: How To Install Expansion Cards
PRIMERGY RX300 S3 User's Guide ■ Notes on Installing Expansion Cards ● Notes on Individual Cards For information about specific expansion cards, see the manual supplied with the card and the notes provided with the server. Also, check the following for various expansion cards.
Page 200 Chapter 7 Installing Internal Options Unlock the slide lock to remove the slot cover. Slide lock Slot cover In the case of slot number 3, 4, or 5, remove the slot cover and PCI card holder. Slide lock PCI card holder Slot cover To remove PCI card holder, remove it by holding its handle.
Page 201 PRIMERGY RX300 S3 User's Guide Attach the expansion card to the PCI card holder 1. Remove the stopper by sliding it down. Stopper 2. Install the expansion card in the PCI card holder and fix it by sliding the stopper from above.
Page 202 Chapter 7 Installing Internal Options Attach the top cover. "7.2 Installing/Removing the Top Cover" (pg.182) Push the server back into the rack. Store the removed slot cover in a safe place. ■ When Using the Standard Card Slot Conversion Feature Turn off the power to the server and all peripheral devices and remove the top cover.
Page 203 PRIMERGY RX300 S3 User's Guide Install the expansion card. Attach the expansion card firmly to the connector of the riser card and fix it by returning the slot cover lock. Install the riser card in the server. Attach the riser card firmly to the connector of the server and fix it by tightening the hand screw.
Page 204: Installing Internal Hard Disk Units
Chapter 7 Installing Internal Options 7.6 Installing Internal Hard Disk Units This section explains how to install internal hard disk units. • Before installing an internal hard disk unit, turn off the server and all peripheral devices, and unplug all power cables from the server. Failure to do so may cause electric shock ( "1.4.3 Turning Off the Server"...
Page 205: Installation Locations Of Internal Hard Disk Units
PRIMERGY RX300 S3 User's Guide 7.6.1 Installation Locations of Internal Hard Disk Units Install the internal hard disk unit in a 3.5-inch storage bay at the front of server. Up to six units can be installed. When an internal backup device is installed, a maximum of four internal hard disk units can be installed.
Page 206: How To Install Internal Hard Disk Units
Chapter 7 Installing Internal Options ■ Correspondence between the Hard Disk Bay Number and the Slot Number The correspondence between the hard disk bay number and the slot number is as follows. Standard installation number When an internal backup device is installed Slot Number 7.6.3 How to Install Internal Hard Disk Units...
Page 207 PRIMERGY RX300 S3 User's Guide ■ How to Remove Internal Hard Disk Units Turn off the server and all peripheral devices. Also unplug all power cables from the server. "1.4.3 Turning Off the Server" (pg.33) Touch a metal part of the server to discharge static electricity.
Page 208: Installing An Internal Backup Device
Chapter 7 Installing Internal Options 7.7 Installing an Internal Backup Device Internal backup device can be installed in a 3.5 inch storage bay. • Before installing the internal backup device, turn off the server and all peripheral devices, and unplug the power cables from the outlet. Failure to do so may cause electric shock ( "1.4.3 Turning Off the Server"...
Page 209: Installable Internal Backup Devices
PRIMERGY RX300 S3 User's Guide 7.7.2 Installable Internal Backup Devices The following internal backup devices can be installed. For details about the internal backup device, see the manual supplied with the internal backup device. table: List of internal backup devices...
Page 210 Chapter 7 Installing Internal Options Remove the fan duct (1) and the L cover (2). Remove the L cover by pushing its tab in the direction of the arrow and raising it. L cover Fan duct Remove all fans and the fan cage. 1.
Page 211 PRIMERGY RX300 S3 User's Guide 4. Draw the fixing lever of fan cage upwards (1), push the fan cage towards the device (2), and raise it upwards (3) to remove it. Fixing lever of fan cage Remove all three cable covers at the side of the device.
Page 212 Chapter 7 Installing Internal Options • Remove the dummy units Press both tabs inwards Dummy units Remove the USB unit. 1. Push the ejector in the direction of an arrow (in front side) while holding up the USB unit lock (green) to unlock it. Lock Ejector Remove the...
Page 213 PRIMERGY RX300 S3 User's Guide Remove the SMB cable and open the holder at the back of the 3.5-inch storage bay while pressing the tabs. Tabs SMB Cable Tilt back SAS backplane. SAS Backplane...
Page 214 Chapter 7 Installing Internal Options Install the internal backup device to bay 2 and bay 3. 1. Connect the power cable and the SCSI cable to the connectors of the internal backup device by putting them through the hole at the back of the 3.5-inch storage bay.
Page 215 PRIMERGY RX300 S3 User's Guide 4. Turn back the SAS backplane and close the both holders at the back of the 3.5-inch storage bay. 5. Connect each cable. • Connect the power cable to the power connector at the back of the hard disk unit.
Page 216 Chapter 7 Installing Internal Options Pull in the SCSI cable into the side of the device and attach the three cable covers. To attach, perform the removal procedure in reverse. Be careful with the front and back of the cover when attaching it. Attach the fan cage and all the fans.
Page 217: Installing An Internal Dvd-Ram Drive Unit
PRIMERGY RX300 S3 User's Guide 7.8 Installing an Internal DVD-RAM Drive Unit An internal DVD-RAM drive unit can be installed in this server by removing the CD- ROM drive. • Before installing the DVD-RAM drive, turn off the server and all peripheral devices, and unplug the power cables from the outlet.
Page 218 Chapter 7 Installing Internal Options Remove the IDE cable form the baseboard. IDE connector Internal hard disk unit Internal hard disk unit Internal DVD-RAM unit Front At this time, do not unplug the power cable. Lift the (green) lock of the internal CD-ROM drive unit and unlock it by sliding the ejector in the direction of the arrow.
Page 219 PRIMERGY RX300 S3 User's Guide Remove the power cable from the power connector of the internal CD-ROM drive unit. Power connector Unplug the IDE cable from the internal CD-ROM drive unit and remove the CD frame. IDE connector Mount the internal DVD-RAM drive unit in the empty CD frame and connect the IDE cable.
Page 220 Chapter 7 Installing Internal Options Connect the power cable to the power connector of the internal DVD-RAM drive unit and install the drive unit in the server. Since the IDE cable is not yet connected, do not install the drive unit completely in the server. Power connector Connect the IDE cable to the baseboard and install the drive unit completely in...
Page 221: Installing Power Supply Units
PRIMERGY RX300 S3 User's Guide 7.9 Installing Power Supply Units One power supply unit (PSU) is installed in this server by default. Up to two PSUs can be installed. By adding one more PSU, the redundant power feature can be enabled.
Page 222 Chapter 7 Installing Internal Options Remove the dummy unit. Remove the screws on the dummy unit and pull it out by the handle. Handle Store the removed screws in a safe place. Install the PSU. Hold the PSU with both hands and insert it straight into the PSU slot. When installing the PSU, be sure to confirm that the connector of the PSU is not damaged or bent.
Page 223 PRIMERGY RX300 S3 User's Guide Remove the PSU by pressing the lever. Pull out the PSU by holding the handle with one hand and supporting the PSU with the other hand. Lever Handle If the PSU is hard to remove, do not pull out it by force. Slide the PSU all the way down once, and then remove it while holding the lever completely down.
Page 224: Connecting Optional External Scsi Devices
Chapter 7 Installing Internal Options 7.10Connecting Optional External SCSI Devices This section explains how to connect optional SCSI devices. 7.10.1 How to Connect Optional External SCSI Devices ■ Connecting a Hard Disk Cabinet for Configuring a High-Capacity Array System Connect the hard disk cabinet as shown below. "Server"...
Page 225 PRIMERGY RX300 S3 User's Guide ■ Notes on Optional External SCSI Device Connections ● SCSI-ID Setting Take care that the settings of each device do not overlap. ● SCSI Cable Connect the optional SCSI device with a SCSI cable that suits the purpose.
Page 226 Chapter 7 Installing Internal Options...
Page 227: Chapter 8 Configuring Hardware And Utilities
Chapter 8 Configuring Hardware and Utilities This chapter explains how to make the necessary environment settings to operate the server. 8.1 BIOS Setup Utility ......228...
Page 228: Bios Setup Utility
Chapter 8 Configuring Hardware and Utilities 8.1 BIOS Setup Utility This section explains how to make settings in the BIOS Setup Utility, and the items of each setting. 8.1.1 Starting and Exiting the BIOS Setup Utility The following explains how to start and exit the BIOS Setup Utility. ■...
Page 229 PRIMERGY RX300 S3 User's Guide ● Key Operations in the BIOS Setup Utility The roles of the keys used for BIOS Setup Utility settings are as follows: table: List of key operations on the BIOS Setup Utility Screen Description [F1] Switches the detailed information display on and off.
Page 230 Chapter 8 Configuring Hardware and Utilities Use the [← ] [→] keys to move the cursor to [Yes] or [No], and press the [Enter] key. • If you selected [Save Changes & Exit] from the Exit menu: Select [Yes] to exit. After saving the changed settings, the BIOS Setup Utility closes and the server restarts.
Page 231: The Main Menu
PRIMERGY RX300 S3 User's Guide 8.1.2 The Main Menu The Main menu is displayed initially when you start the BIOS Setup Utility. Settings for the time and date and for the drives are configured on the Main menu. System Time:...
Page 232: The Standard Ide Submenu
Chapter 8 Configuring Hardware and Utilities 8.1.3 The Standard IDE Submenu This submenu appears when selecting [Standard IDE] from the main menu. Use this submenu to set the type and operating mode for connected IDE devices. PhoenixBIOS Setup Utility Main Advanced Security Server...
Page 233: The Boot Options Submenu
PRIMERGY RX300 S3 User's Guide 8.1.4 The Boot Options Submenu This submenu appears when selecting [Boot Options] from the main menu. Use this submenu to set system startup options. PhoenixBIOS Setup Utility Main Advanced Security Server Exit Boot Options Item Specific Help...
Page 234 Chapter 8 Configuring Hardware and Utilities table: Items on the Boot Options Submenu Item Setting Description Boot Menu Enabled (Unchangeable) Sets whether or not to enable the Boot menu. MultiBoot for HDs Enabled (Unchangeable) Sets whether or not to enable selection of which hard disk unit to load the OS from, when multiple hard disk units are installed.
Page 235: The Advanced Menu
PRIMERGY RX300 S3 User's Guide 8.1.5 The Advanced Menu The Advanced menu sets the peripheral device and PCI device options. PhoenixBIOS Setup Utility Main Advanced Security Server Exit Item Specific Help Setup Warning Setting items on this menu to incorrect values may cause your system to malfunction.
Page 236: The Peripheral Configuration Submenu
Chapter 8 Configuring Hardware and Utilities 8.1.6 The Peripheral Configuration Submenu This submenu appears when you select [Peripheral Configuration] from the Advanced menu. Sets the serial port, parallel port, etc. The items not listed in the figure below can be displayed using the scroll bar. PhoenixBIOS Setup Utility Main Advanced...
Page 237 PRIMERGY RX300 S3 User's Guide table: Items on the Peripheral Configuration Submenu Item Setting Description USB Host Controller Enabled (Unchangeable) Sets whether or not to use the USB controller (2.0 or 1.1 standard). USB 2.0 Host Controller Enabled (Unchangeable) USB BIOS Supported...
Page 238: The Pci Configuration Submenu
Chapter 8 Configuring Hardware and Utilities 8.1.7 The PCI Configuration Submenu This submenu appears when you select [PCI Configuration] from the Advanced menu. Use this submenu to configure the PCI device. PhoenixBIOS Setup Utility Main Advanced Security Server Exit PCI Configuration Item Specific Help >...
Page 239 PRIMERGY RX300 S3 User's Guide ■ The PCI SLOTS Configuration Submenu Use this submenu to configure the PCI slots. table: Items on the PCI SLOTS Configuration Submenu. Item Setting Description PCI Slot 1 Configuration • Disabled (Initial value) Sets whether or not to initialize the extended ROM Option ROM Scan •...
Page 240: The Advanced System Configuration Submenu
Chapter 8 Configuring Hardware and Utilities 8.1.8 The Advanced System Configuration Submenu This submenu appears when you select [Advanced System Configuration] from the Advanced menu. Configures additional settings. PhoenixBIOS Setup Utility Main Advanced Security Server Exit Advanced System Configuration Item Specific Help BIOS Work Space Location: [Expansion ROM Area] Memory Redundancy:...
Page 241 PRIMERGY RX300 S3 User's Guide table: Items on the Advanced System Configuration Submenu Item Setting Description Hardware Prefetch Enabled (Unchangeable) Configures the CPU internal settings. Adjacent Sector Prefetch Enabled (Unchangeable) Configures the CPU internal settings. High Precision Event Timer Disabled (Unchangeable) Sets whether or not to use the high precision event timer of the chipset.
Page 242: The Power On/Off Submenu
Chapter 8 Configuring Hardware and Utilities 8.1.9 The Power On/Off Submenu This submenu appears when you select [Power On/Off] from the Advanced menu. Use this submenu to configure the power on/off settings. PhoenixBIOS Setup Utility Main Advanced Security Server Exit Advanced System Configuration Item Specific Help Power Off Source...
Page 243: The Ipmi Submenu
PRIMERGY RX300 S3 User's Guide 8.1.10 The IPMI Submenu This submenu appears when you select [IPMI] from the Advanced menu. Use this submenu to configure the integrated Remote Management Controller (iRMC) settings. PhoenixBIOS Setup Utility Main Advanced Security Server Exit...
Page 244 Chapter 8 Configuring Hardware and Utilities ■ The LAN Settings Submenu Use this submenu to set the LAN when remote controlled by the RemoteControlService. table: Items on the LAN Settings Submenu Item Setting Description DHCP • Disabled (Initial value) Sets whether or not to acquire LAN IP address of •...
Page 245: The Security Menu
PRIMERGY RX300 S3 User's Guide 8.1.11 The Security Menu The Security menu sets the security options. PhoenixBIOS Setup Utility Main Advanced Security Server Exit Item Specific Help Setup Password Not installed System Password Not installed Set Setup Password: [Press Enter]...
Page 246: The Server Menu
Chapter 8 Configuring Hardware and Utilities table: Items on the Security Menu Item Setting Description Virus Warning Disabled (Unchangeable) Sets whether or not to check if the boot sector of the hard disk drive has been changed since the previous system startup.
Page 247 PRIMERGY RX300 S3 User's Guide table: Items on the Server Menu Item Setting Description O/S Boot Timeout • Disabled (Initial value) Sets whether to enable or disable the "OS Boot • Enabled Monitoring" function when ServerView is installed in the OS.
Page 248: The Cpu Status Submenu
Chapter 8 Configuring Hardware and Utilities table: Items on the Server Menu Item Setting Description Memory Scrubbing Disabled (Unchangeable) Sets whether or not to correct errors in memory domains currently unused by the OS, or by application programs. CPU Status Sets whether or not to allow the use of the installed CPU.
Page 249: The Memory Status Submenu
PRIMERGY RX300 S3 User's Guide 8.1.14 The Memory Status Submenu This submenu appears when you select [Memory Status] from the Server menu. Use this submenu to set whether or not to allow the use of the installed memory modules. PhoenixBIOS Setup Utility...
Page 250: The Console Redirection Submenu
Chapter 8 Configuring Hardware and Utilities 8.1.15 The Console Redirection Submenu This submenu appears when you select [Console Redirection] from the Server menu. Use this submenu to configure detailed settings for console redirection. PhoenixBIOS Setup Utility Main Advanced Security Server Exit Console Redirection Item Specific Help...
Page 251: The Exit Menu
PRIMERGY RX300 S3 User's Guide 8.1.16 The Exit Menu This menu exits the BIOS Setup Utility. PhoenixBIOS Setup Utility Main Advanced Security Server Exit Item Specific Help Save Changes & Exit Discard Changes & Exit Get Default Values Load Previous Values...
Page 252 Chapter 8 Configuring Hardware and Utilities...
Page 253 Chapter 9 Operation and Maintenance This chapter explains the operations necessary after starting to use this server as well as daily care and maintenance. 9.1 Daily Maintenance ......254 9.2 Troubleshooting .
Page 254: Chapter 9 Operation And Maintenance
This section explains how to check the status of the operating server, as well as how to perform daily maintenance. ● Information for PRIMERGY For the latest information on PRIMERGY, update modules, drivers and the software, refer to the Fujitsu PRIMERGY website. http://primergy.fujitsu.com 9.1.1 Checking the Server Condition Use the status LED or server monitoring tool to check the server status.
Page 255 PRIMERGY RX300 S3 User’s Guide ■ Cleaning the Server Wipe with a soft, dry cloth. For stains that do not come off with a dry cloth, wipe with a cloth lightly dampened with a mild detergent. Once the stain has been removed, wipe off any remaining detergent with a cloth dampened with water.
Page 256 Chapter 9 Operation and Maintenance ■ Cleaning the Floppy Disk Drive Prolonged use of the floppy disk drive accumulates dust on the device head (the part which reads/writes data). A dirty head can impair the ability to read/write data to/from a floppy disk correctly. Clean the head once every three months.
Page 257: Troubleshooting
Contacting Maintenance Support" ( pg.288) and collect the required information. ● Information for PRIMERGY For the latest information on PRIMERGY, update modules, drivers and the software, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com). 9.2.1 Hardware Troubleshooting This section explains hardware related troubleshooting. If the server does not operate properly or if a failure is suspected, check the following.
Page 258 Chapter 9 Operation and Maintenance ● A temperature warning is output to the hardware event log and OS event log, or ServerView issues a notification of a temperature warning such as by a popup message. The above log is output or the above notification is issued by ServerView when the ambient temperature is within 30 to 35 °C, which is near the upper limit of the temperature boundaries (10 to 35 °C).
Page 259 PRIMERGY RX300 S3 User’s Guide The display may also shake if a nearby cell-phone receives a call. Do not use a cell-phone near the display. ● The screen display is distorted. The screen display may be distorted during 3D program execution or the 3D program may terminate abnormally.
Page 260: Error Messages
Uncorrectable memory error in module x Memory decreased in Size Power off the server and turn it back on. If the message still appears, check the error log and replace the faulty memory. Non Fujitsu Siemens Memory Module The memory is abnormal. detected Warranty void!
Page 261 PRIMERGY RX300 S3 User’s Guide table: List of POST error messages Message Description System battery is dead - Replace and run The memory is abnormal. Contact an office listed in the SETUP "Contact Information" of the "Start Guide". System CMOS checksum bad - Default The CMOS is abnormal.
Page 262 Chapter 9 Operation and Maintenance table: List of POST error messages Message Description Incorrect Drive A - run SETUP Correct the settings of [Diskette A] or [Diskette B] on the"8.1.2 The Main Menu" ( pg.231) of the BIOS Setup Utility. Incorrect Drive B - run SETUP System Cache Error - Cache disabled The cash error occurs in the system, stop the server once, then...
Page 263 PRIMERGY RX300 S3 User’s Guide table: List of POST error messages Message Description Invalid NVRAM media type The NVRAM is abnormal. Power off the server and turn it back on. If the message still appears, the baseboard must be replaced.
Page 264 Chapter 9 Operation and Maintenance table: List of POST error messages Message Description Power supply fan status is warning PSU fan rotation error. Replace the PSU fan. If the message still appears, the baseboard must be replaced. Contact an office listed Power supply fan status is critical in the "Contact Information"...
Page 265 PRIMERGY RX300 S3 User’s Guide table: List of Server Management Tools Error Messages Message Description ERROR:Fail to create data file. The following are possible causes. Check the floppy disk status again. ERROR:Fail to write 1st CMOS data into data file. nn •...
Page 266: Software Troubleshooting
Chapter 9 Operation and Maintenance 9.2.3 Software Troubleshooting This section explains software related troubleshooting. For troubles during OS installation or system operation, refer to the following contents. ■ Trouble at a ServerStart Startup ● After a boot from the ServerStart CD-ROM, nothing is displayed on the screen.
Page 267 PRIMERGY RX300 S3 User’s Guide ■ Error Messages during Installation The following error messages may appear during installation using ServerStart. Check the corrective action against the relevant error. ● "WzDiskAdmin: System Error! ......, Last Error: The device is not ready." appears.
Page 268 Chapter 9 Operation and Maintenance Start the command prompt and execute the following commands to extract "tftp.exe" in the "%Systemroot%\system32" folder. [CD-ROM drive]:\i386>expand -r:tftp.exe TFTP.EX_ %Systemroot%\system32 Confirm that "tftp.exe" exists in the "%Systemroot%\System32" folder. ■ Error Window Appears after LAN Driver Installation (on Windows Server 2003) The following window may appear when the installation of the LAN driver to the [Ethernet controller] under [Other devices] starts.
Page 269 PRIMERGY RX300 S3 User’s Guide ■ Event Log Errors after Installation After installation, the following events may be displayed in Event Viewer. Check and perform the corrective action against the relevant event. table: Error events at installation Description Cause and corrective action...
Page 270 Chapter 9 Operation and Maintenance ● Collect memory dump to other than the system drive If the memory dump was set to be collected to the system drive (C:\), change the settings so that the memory dump can be saved to a drive other than the system drive. For setting procedures, refer to "5.1 Memory Dump/Paging File Setting"...
Page 271 PRIMERGY RX300 S3 User’s Guide ■ Fails in Remote Installation If remote installation fails, check the following. ● Checking Services Check that the DHCP, PXE Service, and TFTP Service are running. For checking procedures, refer to "3.4 Remote Installation" ( pg.88).
Page 272 Chapter 9 Operation and Maintenance ■ SNMP Service Startup Fails Regardless of whether the Simple Network Management Protocol (SNMP) is installed, if the SNMP service is not started, perform the following procedure to start the SNMP service. ● For Windows Server 2003 Click [Start] [Administrative Tools] [Computer Management].
Page 273 PRIMERGY RX300 S3 User’s Guide ● Changing the Time Settings for the OS and Hardware Clock In a Linux environment, the time displayed on the OS (the software clock value on the OS) is written to the hardware clock on the server when the OS is shut down.
Page 274: System Event Log
Chapter 9 Operation and Maintenance 9.3 System Event Log To operate system event log, use Server Management Tools. When the area for writing to the system event log is full, the server is set to automatically overwrite older event logs. For details on this setting, refer to "8.1.10 The IPMI Submenu" ( pg.243) under the [Advanced] menu of the BIOS Setup Utility.
Page 275 PRIMERGY RX300 S3 User’s Guide Insert the "Server Management Tools" disk supplied with this server and turn the power on. The system will boot from the floppy disk and the DOS prompt is displayed. Enter the following command and press the [Enter] key.
Page 276: Viewing The System Event Log
The menu window of Server Management Tools appears. Use the [↑] and [↓] keys to select [System Event Log (SEL)], and press the [Enter] key. The [SYSTEM EVENT LOG (SEL)] window appears. FUJITSU SIEMENS SYSTEM EVENT LOG (SEL) COMPUTERS 004 MMM-DD-YYYY HH:MM:SS [*****] ****************************************...
Page 277: Saving/Deleting The System Event Log
PRIMERGY RX300 S3 User’s Guide 9.3.3 Saving/Deleting the System Event Log When the system event log is full, the oldest log is overwritten with the newest log. Periodically check the system event log and save/delete as necessary. ■ Saving the System Event Log Start Server Management Tools.
Page 278: Security
Chapter 9 Operation and Maintenance 9.4 Security Security features are provided in order to protect the server hardware and software from theft. Additional security functions, which prevent unauthorized use, provided by the BIOS Setup Utility are also available to help maintain a highly reliable data security system.
Page 279: Security Against Unauthorized Use
PRIMERGY RX300 S3 User’s Guide 9.4.2 Security against Unauthorized Use A password can be set to prevent unauthorized use of the server. When a password is set, the server is accessible only to the users who know the password. The password is set in the BIOS Setup Utility. For details on the BIOS Setup Utility, refer to "8.1.11 The Security Menu"...
Page 280 Chapter 9 Operation and Maintenance In the [Confirm New Password] field, enter the password you have entered in Step 4 and press the [Enter] key. [System Password] or [Setup Password] on the [Security] menu shows [Installed]. When only the user or administrator password is set, the same setting items are accessible to both users and administrators.
Page 281: Security When Disposing Of The Server
PRIMERGY RX300 S3 User’s Guide 9.4.3 Security When Disposing of the Server ■ Notes regarding the Deletion of Data from the Hard Disk When Disposing of or Transferring the Server When disposing of or transferring a server that has been used, the data in the hard disk may be read and used unscrupulously.
Page 282: Backup
Chapter 9 Operation and Maintenance 9.5 Backup This server utilizes high reliability components and hard disks, however, as a precautionary measure, it is recommended that periodic backups be taken of the data. 9.5.1 Importance of Backups A backup of data stored on the server is required for data restoration in the event of server trouble resulting in a system failure or accidental data loss due to operational errors.
Page 283 PRIMERGY RX300 S3 User’s Guide ■ Notes on Operating Backups Notes on operating backups are as follows. For details, refer to the device manuals. ● Head Cleaning Airborne dust and dust from the magnetic media can collect on the head of the magnetic tape device. To remove this dust, head cleaning must be implemented.
Page 284 Chapter 9 Operation and Maintenance ● Ejecting Media after a Backup Some backup software products provide functions for ejecting media after a backup is completed. Such functions will rewind the tape after a backup is completed and then eject the media from the drive. Be sure to execute this function for autoloader/library devices.
Page 285: Restoring The System
PRIMERGY RX300 S3 User’s Guide 9.6 Restoring the System In the unfortunate event where the system file, system configuration, or environment changes during startup are corrupted, use the repair information stored on the recovery disk created at the installation to restore the system.
Page 286: For Windows 2000 Server
Chapter 9 Operation and Maintenance 9.6.2 For Windows 2000 Server ● Items Required • Windows 2000 Server CD-ROM • Windows 2000 Server system recovery disk (created beforehand) Insert the Windows 2000 Server CD-ROM immediately after the server is turned on. Confirm that there is no floppy disk in the floppy disk drive.
Page 287: Reinstalling The Os
PRIMERGY RX300 S3 User’s Guide 9.7 Reinstalling the OS This section explains the procedure for reinstalling the OS. 9.7.1 Checking before OS Reinstallation ■ Removing the Optional Devices Remove the following optional devices before reinstallation. Install or connect them after OS installation.
Page 288: Maintenance Service
Chapter 9 Operation and Maintenance 9.8 Maintenance Service This section explains the details of the maintenance service. If the cause of the failure is uncertain or if the original condition cannot be restored, contact the seller or an office listed in the "Contact Information" of the "Start Guide". 9.8.1 Contacting Maintenance Support For "Contact Information", refer to "Start Guide".
Page 289: Appendix
Appendix This appendix explains the specifications for the server and for its internal options. A Server Specifications ......290 B Specifications for Internal Options .
Page 290: A Server Specifications
Appendix Server Specifications This section explains the specifications for the server. Diskless Type table: Server Specifications - Diskless Type Item Functions and Specifications Product ID PGUR3031A ® ® Standard Intel Xeon Processor 5050 3.0GHz (667MHz FSB) 2 × 2MB Level 2 cache Number of 1(Max.2) multiplication...
Page 291 PRIMERGY RX300 S3 User’s Guide ● Supported OS The following OSs are supported. • Windows Server 2003, Standard Edition • Windows Server 2003, Enterprise Edition • Windows Server 2003, Standard x64 Edition • Windows Server 2003, Enterprise x64 Edition • Windows Server 2003 R2, Standard Edition •...
Page 292: B Specifications For Internal Options
Appendix Specifications for Internal Options This section explains the specifications for internal options for the server. When you have bought an internal option as a standard option, check that the package contains the following items before use. Should it happen that items are missing, contact an office listed in the "Contact Information"...
Page 293: Memory
PRIMERGY RX300 S3 User’s Guide Memory ■ Package • DIMM (2) ■ Specifications table: Memory Specifications Item Function and Specifications Product Name Memory Module-1GB Memory Module-2GB Memory Module-4GB Models PG-RM1CD PG-RM2CD PG-RM4CD Modules 512MB DDR2 533 FBD x 2 1GB DDR2 533 FBD x 2...
Page 294: Basic Card Slot Conversion Kit
Appendix Basic Card Slot Conversion Kit ■ Package • Basic card slot conversion kit (1) ■ Specifications table: Basic Card Slot Conversion Kit Specification Item Function and Specification Product Name Basic card slot conversion kit Models PGBCSU103 Parallel Port Option Specifications ■...
Page 295: Power Cord Selection
PRIMERGY RX300 S3 User’s Guide Power Cord Selection The power cord for this unit has been packed separately and has been selected according to the country of destination. It must be used to prevent electric shock. Use the following guidelines if it is necessary to replace the original cord set.
Page 296 Appendix ● For units set at 230 V (outside of the United States and Canada): Use a cord set consisting of a minimum AWG according to the table above and a grounding type attachment plug rated 15 A, 250 V. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed and should be marked HAR.
Page 297: C Using The Server Management Port
PRIMERGY RX300 S3 User’s Guide Using the Server Management Port This server supports the server management port. When a personal computer (PC) is connected to the serial port of this server with an RS-232C cross cable, the PC can be used to control (turn on/off and reset) the server power supply.
Page 298 Appendix ■ Connecting the Server to a PC Connect the server to a PC using an RS-232C cross cable. This server has two serial ports. Connect the cable to Serial Port 1. Server Rear Serial Port RS-232C cross cable PC Rear Serial Port ■...
Page 299: Remote Power Supply Control
PRIMERGY RX300 S3 User’s Guide Remote Power Supply Control This section explains how to control the server power supply remotely. The server power supply can be remote-controlled with the terminal software on the PC. ■ Starting Up the Remote Controller Start up the terminal software.
Page 300 Welcome to PRIMERGY Remote Manager Firmware Revision x.xxA (x.xx) SDRR *.** ID 0203 RX300S3 Firmware built xxx xx xxxx xx:xx:xx * **************************************** System Type : PRIMERGY RX300 S3 System ID : xxxxxxxx System Name : RX300S3-2 (xxx.xxx.xxx.xxx) System OS : xxxxxxxx System Status: OK...
Page 301 PRIMERGY RX300 S3 User’s Guide Select a menu and press the corresponding number key. "*" is displayed in the bracket of unavailable menu. table: Remote Control Menu Menu name Operation Immediate Power Off Turns the server off. Immediate Reset Resets the server.
Page 302: D Remote Management Controller
(iRMC) and the optional Remote Management Controller Upgrade (PG-RMCU1). Overview of the Remote Management Controller PRIMERGY RX300 S3 has the Remote Management Controller on the baseboard. The Remote Management Controller makes the hight-quality, high-reliability remote service board function possible. To use the console redirection function and the remote storage function, the license key of optional Remote Management Controller Upgrade (PG-RMCU1) is necessary.
Page 303 PRIMERGY RX300 S3 User’s Guide Turn on the server. Press the [F2] key during POST to start up the BIOS Setup Utility. Select the [Advanced] menu → [IPMI] → the [LAN Settings] submenu, and set the each item. ■ For setting items, refer to "...
Page 304: Window Of The Remote Management Controller
Appendix Window of the Remote Management Controller The Remote Management Controller uses the Web interface function. The following window appears when starting the Remote Management Controller. The following functions are available. table: Functions of the Remote Management Controller Item Description System Information Displays information of the system.
Page 305: Remote Management Controller Upgrade (Pg-Rmcu1)
PRIMERGY RX300 S3 User’s Guide ■ Comparison with server management function of ServerView "ServerView", software provided with the server, can manage the server remotely if OS is normally operating. The Remote Management Controller can operate even in the state of the server hang, therefore, it is effective when the server cannot be monitored by ServerView.
Page 306 Appendix ● Remote Storage Function This is a function to recognize the external memory device connected by using the console redirection function as a remote device of the server. The configuration of the remote storage function is shown in the figure below. CD-ROM drive Accessing as the remote drive Floppy disk drive...
Page 307: E Recycling
PRIMERGY RX300 S3 User’s Guide Recycling This section explains how to recycle this server. ■ Disposing of the Server When scrapping this server, contact an office listed in the "Contact Information" of "Start Guide". This server must be disposed of as industrial waste.
Page 308 Appendix...
Page 309 PRIMERGY RX300 S3 User’s Guide Index CPU ......180, 184 Installing ......185 Active Directory.
Page 310 Installing......206 Removing..... . . 207 Global Array Manager .
Page 311 PRIMERGY RX300 S3 User’s Guide OS installation Preparation of remote resources ..98 Installation method ....46 Preparation of the PXE server..91 Precautions .
Page 312 Windows Server 2003 ... . . 146 Windows 2000 Server ... . . 147 Temperature monitoring ....175 Top Cover .
Page 313 FUJITSU LIMITED • The contents of this manual may be revised without prior notice. • Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. • No part of this manual may be reproduced in any without the prior written...

Fujitsu PRIMERGY RX300 S3 User Manual

Chapter1 Overview

Chapter 2 Checking before os Installation

Chapter 3 OS Installation Using Serverstart

Chapter 4 Manual os Installation

Chapter 5 Operations after os Installation

Chapter 6 High Reliability Tools

Chapter 7 Installing Internal Options

Chapter 8 Configuring Hardware and Utilities

Chapter 9 Operation and Maintenance

Appendix

Quick Links

Troubleshooting

Related Manuals for Fujitsu PRIMERGY RX300 S3

Summary of Contents for Fujitsu PRIMERGY RX300 S3