Table of Contents
Advertisement
Maintenance
3.8.10 Advanced operating functions
CL5000iU 4CC ...
▶ Press the Set key.
▶ Press the Set key or ., / keys to select the function.
–
= Sleep mode
–
= Follow Me function
–
= Wireless control function
▶ Confirm selection with the OK key.
Exiting the function:
▶ Repeat the above steps.
CL5000iL 4C ...
▶ Press the Set key.
▶ Press the Set key or ., / keys to select the function.
–
= Self-cleaning
–
= Sleep mode
–
= Follow Me function
–
= Wireless control function
▶ Confirm selection with the OK key.
Exiting the function:
▶ Repeat the above steps.
Self-cleaning (
, CL5000iL 4C ...)
The device has a self-cleaning function for the evaporator. The self-
cleaning freezes dust, mould and grease. Everything is then quickly
defrosted and dried with hot air.
Sleep mode
The purpose of this function is to save energy during idle times. After an
hour, the device heats or cools less intensely. To do this, the set
temperature is changed by 1 °C. After two hours, the set temperature
changes by a further 1 °C. Then it remains at the new temperature.
The function is not available in dehumidification mode and Fan Mode.
Follow me function (Follow Me)
The function activates the remote control at the current location in order
to measure the temperature at 3-- minute - intervals. The indoor unit is
now controlled with reference to these measurements.
The Follow Me function is only available in cooling mode, heating mode
and automatic mode.
Wireless control function
The purpose of this function is to establish a connection via WLAN.
To connect to WLAN an IP-Gateway (optional accessory) must be
installed.
NOTICE
For TWIN installation, an IP gateway is sufficient for the master unit. No
gateway is required for the slave unit.
38
4
Maintenance
CAUTION
Danger due to electric shock or moving parts
▶ Disconnect the power supply before carrying out any maintenance
work.
▶ Have any maintenance steps that are not listed here carried out by an
approved contractor.
4.1
Replacing the batteries
You require 2 size AAA batteries. Using rechargeable batteries is not
recommended.
▶ Remove the battery cover ( Fig. 7).
▶ Insert new batteries, ensuring correct polarity.
▶ Reinstall the cover.
4.2
Cleaning the unit and the remote control
NOTICE
Damage to unit due to incorrect cleaning!
▶ Do not directly splash or pour water onto them.
▶ Do not use hot water, thinner, abrasive powders or strong solvents.
▶ Clean indoor unit and remote control by wiping them with a soft cloth.
▶ Only have the outdoor unit cleaned by an approved contractor.
4.3
Cleaning the air filter
NOTICE
The air filter may deform in direct sunlight.
▶ Do not expose the air filter to direct sunlight.
Check the air filter every 2 weeks and clean if necessary. Always clean
before and after decommissioning for longer periods.
▶ Open the air inlet grille ( Fig. 3).
▶ Remove the air filter.
▶ Clean the air filter using a vacuum cleaner, or wash out with hot water
and a mild cleaning agent and dry in the shade.
If you clean the filter with water, the outer side of the air inlet grille should
be facing downwards away from the water jet, and when cleaning with
the vacuum cleaner it should be facing up towards the vacuum cleaner.
4.4
Decommissioning for longer periods
Before decommissioning for longer periods:
▶ Clean the air filter.
▶ Activate the self-cleaning of the indoor unit using the Clean button.
▶ After self-cleaning, switch on the fan mode until the indoor unit is dry.
▶ Turn off indoor unit and disconnect power supply.
▶ Take batteries out of the remote control.
▶ Protect the devices from dust.
Climate 5000i U/L – 6721841495 (2021/10)
Advertisement
Table of Contents
