Sharp LS013B7DH07 Technical Literature

Lcd module

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Table of Contents

Summary of Contents for Sharp LS013B7DH07

Page 3 SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes.
Page 4 (6) Be careful to handle this LCD panel in order to avoid injury yourself as this panel is made of glass and have sharp edge. When the panel is broken, do not touch the glass. Although the panel is difficult to be scattered, touching the broken part may hurt your hands.
Page 5 Do not use the LCD module under such environment. (12) To avoid picture uniformity failure, do not put a seal or an adhesive material on the LCD panel surface. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 6 Proper measure should be taken to avoid static electricity charge (electrostatic earth: 100Mohms).There is a possibility that the static electricity is charged to them without leakage in case of insulating floor, so the electrostatic earth: 100Mohms should be made. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 7 Otherwise LCD panel may be damaged. (6) Do not use the LCD panel under outside of specified driving timing chart. Otherwise LCD panel may not have proper picture quality. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 8 (12) According to the using application, power circuit protection is recommended at module failure. (13) Nature of dew consideration prevention is necessary when LCD is used for long time under high-temperature and high-humidity ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 9 Store in normal room temperature as much as possible. (3) Keeping Method a. Don't keeping under the direct sunlight. b. Keeping in the tray under the dark place. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 10 (approximately 100mg) and therefore it will not leak even if the panel should break. Its median lethal dose (LD50) is greater than 2,000 mg/kg and a mutagenetic (Aims test: negative) material is used. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 11: Table Of Contents
9. Display Qualities ............................27 10. External capacitors ............................. 27 11. Marking ................................. 28 12. Packaging ..............................29 13. Reliability Test Conditions ......................... 31 14. Outline dimensions ............................. 32 ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 12: Outline
Outline Dimension 24.68 (W) × 30.00 (H) × 0.745 (D) Mass 1.1 (max) Surface Hardness Pencil hardness Surface treatment (Note) Detail dimension and tolerance are shown in fig. 14-1 ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 13: Input Terminal Names And Functions
< EXTMODE=”Hi” > COM Signal Serial Flag Ｉnput External COM Signal Input SCLK SCLK EXTCOMIN EXTCOMIN DISP DISP VDDA VDDA EXTMODE EXTMODE VSSA VSSA Figure 4-1 Recommended circuit ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 14 Cndensation will cause electeical leak and may cause the module to not meet this specification. [Note 5-5] Operating temperature is the temperature that guarantees only for the operation. For contrast, response time, and other display quality determination, use Ta＝＋25℃. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 15: Electrical Characteristics
VSS+0.1 *It can be operated below VDD voltage, however, operation around 3V is recommended. [Note 6-1] Applies to EXTMODE=”Hi” [Note 6-2] Applies to SCLK, SI, SCS, DISP, EXTCOMIN. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 16 Remark 1)When power on , VDDand VDDA are same timem or VDD should be faster than the VDDA. Remark 2) When power off, VDD and VDDA are same time or VDDA shoud be faster than the VDD. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 17 404.55 EXTCOMIN signal frequency fEXTCOMIN EXTCOMIN signal rising time trEXTCOMIN EXTCOMIN signal folling time twEXTCOMIN EXTCOMIN signalHigh duration thlEXTCOMIN DISP Rising time trDISP DISP Folling time tfDISP ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 18 SPEC No. MODEL No. PAGE LD-28204A LS013B7DH07 6-4) Signal Timing COM signal serial input (EXTMODE=”Lo”) ※SCS,SI,SCLK、DISP、EXTCOMIN: 3V input voltage Figure 6-4 Signal Timing ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 19 【Remark 6-6】 This is value in steady condition, not the falue of peak power at the time of COM operation. Some marging for power supply is recommended. We recommend capacitor for VDD and VDDA. (If VDD and VDDA are on separate systems, we recommend capacitor for each.) ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 20 ※For gate line address setting, refer to 6-7) Input Signal and Display. ※M1: Frame inversion flag is enaled when EXTMODE=”Lo”. ※When SCS becomes “Lo”, M0 and M2 are cleared. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 21 ※ For gate line address setting, refer to 6-7) Input Signal and Display. ※ Input data continuously. ※ M1: Frame inversion flag is enabled when EXTMODE=”Lo”. ※ When SCS becomes “Lo”, M0 and M2 are cleared. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 22 DUMMY DATA: Dummy data. It can be “Hi” or “Lo” (“Lo” is recommended.) ※ M1: Frame inversion flag is enabled when EXTMODE=”Lo” ※ When SCS becomes “Lo”, M0 and M2 are cleared. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 23 ※1：LC inversion has been changed by M1 flag statement. ※2：The periods of plus polarity and minus polarity should be same length as much as possible. Figure 6-10 COM Inversion (EXTMODE=Lo) ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 24 ※ 4： LC inversion polarity has been set by the rising edge of EXTCOMIN. ※ 5： The period of EXTCOMIN should be constant. Figure 6-12 COM Inversion 2 (EXTMODE=Hi) ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 25 P1,L168 P144,L168 Gate line address setting AG0 AG1 AG2 AG3 AG4 AG5 AG6 AG7 ：：：：：：：：： Figure 6-13 Data position ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 26: Optical Characteristics
Figure 7-1 Defintion of Viewing Angle [Note 7-2] Defintion of Contrast Retio The contrast ratio is defined as the following. Reflection intensity in white display Contrast ratio(CR) ＝ Reflection intensity in black display ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 27 It’s difined by the time change of optical receiver output when signal is input to display white or black White Black 100% Optical receiver output (Incremental ) Time τr τd Figure 7-4 Respons time ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 28: Pin Assignment
Condition (2) Minimum bend R: Inner diameter R0.45 Figure 8-2 FPC Bend Specification 【Remark 8-1】 Do not bend to the front polarizer film side. 【Remark 8-2】 Bend frequency: 3 times or less (Repeat bend condition: 180°～ 0°) ©Copyright 2016 SHARP All rights reserved...
Page 29: Display Qualities
※Above circuit and parts are only recommendation. For actual use, please evaluate their conformity with your system and design. (Capacitor pressure resistance can be larger than resistance indicated above.) ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 30: Marking
M : Single-digit Month (1,2,--,9,X,Y,Z) DD : Digit of the day (01,--,31) P : Code of manufacture 01234A 01234 : Five-digit in Consecutive number (Traceabillity number) A : Product revision ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 31: Packaging
・Vibration Please refrain from keeping the product in the place which always has vibration. ・Storage Period: Within above mentioned conditions, maximum storage period should be 3 months ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 32 12-2) Packaging form figure The packing condition is shown in Figure. 12-1 The packaging is designed such that the module does not break during transit. Figure. 12-1 Packaging Form ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...
Page 33: Reliability Test Conditions
Electro static discharge test [Remark] Ta = Ambient temperature, Tp = Panel temperature (Evaluation method) In the standard condition, there shall be no practical problems that may affect the display function. ©Copyright 2016 SHARP All rights reserved ©Copyright 2016 SHARP All rights reserved...

Sharp LS013B7DH07 Technical Literature

Quick Links

Related Manuals for Sharp LS013B7DH07

Summary of Contents for Sharp LS013B7DH07

Table of Contents