Page 1
CD RECEIVER !" ‡§√◊ Ë Õ ß‡≈Ë π • This unit is equipped with the display demonstration. To cancel it, see page 8. !"#$%&'()*+,&'-./01=8 • • ‡§√◊ Ë Õ ßπ’ È ‰ ¥È √ — ∫ °“√µ‘ ¥ µ— È ß °“√ “∏‘ µ ¿“æª√–°Õ∫ À“°µÈ Õ ß°“√¬°‡≈‘ ° ‚ª√¥¥Ÿ ÀπÈ “ For installation and connections, refer to the separate manual.
IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. CONTENTS How to reset your unit ... How to use the MODE button ...
Remote controller SOUND SOURCE 1 • Turns on the unit if pressed when the unit is turned off. • Turns off the unit if pressed and held until “SEE YOU” appears on the display. • Drops the volume level in a moment if pressed briefly.
Preparing the remote controller Before using the remote controller: • Aim the remote controller directly at the remote sensor on the main unit. Make sure there is no obstacle in between. Remote sensor • Do not expose the remote sensor to strong light (direct sunlight or artificial lighting).
Turning on the power Turn on the power. Note on One-Touch Operation: When you select a source in step 2 below, the power automatically comes on. You do not have to press this button to turn on the power. Select the source. To operate the tuner (FM or AM), see pages 10 –...
Canceling the display demonstration When shipped from the factory, display demonstration has been activated, and starts automatically when no operations are done for about 20 seconds. • It is recommended to cancel the display demonstration before you use the unit for the first time.
Setting the clock Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. (PSM: see page 27.) Set the hour. 1 Select “CLOCK HOUR” if not shown on the display. 2 Adjust the hour.
RADIO OPERATIONS Listening to the radio You can use either automatic searching or manual searching to tune in to a particular station. Searching for a station automatically: Auto search Select the band (FM1 – 3, AM). Each time you press the button, the band changes as follows: FM 1...
Tune in to a station you want while “M.SEEK” (manual seek) is still on the display. To tune in to stations of higher frequencies To tune in to stations of lower frequencies • If you release your finger from the button, the manual mode will automatically turns off after 5 seconds.
Manual preset You can preset up to 6 stations in each band (FM1, FM2, FM3, and AM) manually. Ex.: Storing FM station of 92.5 MHz into the preset number 1 of the FM1 band. Select the band (FM1 – 3, AM) you want to store stations into (in this example, FM1).
Refer to “MP3/WMA OPERATIONS” on pages 18 to 22 for operating MP3/WMA discs. Playing a CD Open the control panel. Note on One-Touch Operation: When a CD is already in the loading slot, pressing CD/CD-CH turns on the unit and starts playback automatically.
To stop play and eject the CD Press 0. CD play stops and the control panel moves down. The CD automatically ejects from the loading slot. • If you change the source or turn the power off, CD play also stops (without ejecting the CD). Next time you select “CD”...
How to use the +10 and –10 buttons • Ex. 1: To select track number 32 while playing track number 6 (Three times) \ 10 \ 20 \ 30 Track 6 • Ex. 2: To select track number 8 while playing track number 36 (Three times) \ 30 \ 20 \ 10...
Playing a CD Text In a CD Text, some information about the disc (its disc title, performer, and track title) is recorded. This CD Text information will be shown automatically when you play a CD Text. To change the CD Text information manually, select text display mode while playing a CD Text.
What are MP3/WMA? MP3 is an abbreviation of Motion Picture Experts Group (or MPEG) Audio Layer 3. MP3 is simply a file format with a data compression ratio of 1:10 (128 Kbps*). ® WMA (Windows Media Audio) is the digital audio compression format developed by Microsoft Corporation.
MP3/WMA OPERATIONS Refer also to “CD OPERATIONS” on pages 13 to 16. Playing a disc Open the control panel. Note on One-Touch Operation: When a disc is already in the loading slot, pressing CD/CD-CH turns on the unit and starts playback automatically.
To stop play and eject the disc Press 0. Playback stops and the control panel moves down. The disc automatically ejects from the loading slot. To change the display information While playing back an MP3/WMA file, you can change the disc information shown on the display.
Page 20
To go to a particular file quickly within the current folder (+10 and –10 buttons) Press MODE to enter the functions mode while playing a disc. Press +10 or –10. To skip 10 files* forwards to the last file To skip 10 files* backwards to the first file * First time you press +10 or –10 button, the file skips to the nearest higher or lower file...
To skip to the next or previous folder Press 5 (up) while playing a disc to skip to the next folder. Each time you press the button consecutively, the next folder is located (and the first file in the folder starts playing, if recorded). Press ∞...
Page 22
To play back files repeatedly (Track Repeat/Folder Repeat Play) You can play back the current file or all the files in the current folder repeatedly. Press MODE to enter the functions mode while playing a disc. Press RPT (repeat), while “MODE”...
Adjusting the sound You can adjust the sound characteristics to your preference. Select the item you want to adjust. Each time you press the button, the adjustable items change as follows: (fader) (balance) WOOFER (volume) (subwoofer) Indication To do: Adjust the front and rear speaker balance.
Selecting preset sound modes (iEQ: intelligent equalizer) You can select a preset sound mode (iEQ: intelligent equalizer) suitable to the music genre. • There is a time limit in doing the following procedure. If the setting is canceled before you finish, start from step 1 again.
Storing your own sound adjustments You can adjust the sound modes to your preference and store your own adjustments in memory (USER 1, USER 2 and USER 3). • There is a time limit in doing the following procedure. If the setting is canceled before you finish, start from step 1 again.
OTHER MAIN FUNCTIONS Changing the general settings (PSM) You can change the items listed in the table on page 27 by using the PSM (Preferred Setting Mode) control. Basic Procedure Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display.
Page 27
Preferred Setting Mode (PSM) items • For detailed operations of each PSM items, refer to the pages listed in the table. Indications DEMO MODE Display demonstration CLOCK HOUR Hour adjustment CLOCK MINUTE Minute adjustment CLOCK DISP Clock display LEVELMETER Level meter DIMMER MODE Dimmer mode TELEPHONE...
Page 28
To set the clock display—CLOCK DISP You can set the clock to be shown on the lower part of the display when the unit is turned on. When shipped from the factory, the clock is set to be shown on the display. •...
Page 29
To select the telephone muting —TELEPHONE This mode is used when a cellular phone system is connected. Depending on the phone system used, select either “MUTING 1” or “MUTING 2,” whichever mutes the sounds from this unit. When shipped from the factory, this mode is deactivated.
Page 30
To select the external component to use —EXTERNAL IN You can connect the external component to the CD changer jack on the rear using the Line Input Adapter KS-U57 (not supplied). To use the external component as the playback source through this unit, you need to select which component—CD changer or external component—to use.
Assigning names to the sources You can assign names to station frequencies and CDs (both in this unit and in the CD changer). After assigning a name, it will appears on the display when you select the source. Maximum number of Sources characters Station frequencies...
Changing the control panel angle You can change the angle of the control panel in four positions. Press (angle) repeatedly to adjust the angle of the control panel to the position you want. The control panel angles changes as follows: ANGLE 01 ANGLE 04 Note:...
Detaching the control panel You can detach the control panel when leaving the car. When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching the control panel Before detaching the control panel, be sure to turn off the power.
CD CHANGER OPERATIONS We recommend that you use the JVC MP3- compatible CD changer with your unit. By using this CD changer, you can play back your original CD-Rs (Recordable) and CD-RWs (Rewritable) recorded either in audio CD format or in MP3 format.
Page 35
Note: Folder name appears on the display instead of “ROOT,” if an MP3 disc contains a folder. • When the current disc is a CD: Playback starts from the first track of the current disc. Selected disc number* Current track Elapsed playing time number * When “CLOCK DISP”...
Page 36
To show the disc information for CD Text and MP3 discs This is possible only when connecting a JVC CD changer equipped with CD Text and/or MP3 disc information reading capability. Select text display mode while playing a CD Text or an MP3 disc.
Selecting the playback modes To play back tracks/files at random (Folder Random/Disc Random/Magazine Random Play) Press MODE to enter the functions mode while playing a disc. Press RND (random), while “MODE” is still on the display. Each time you press the button, the random play mode changes as follows: For MP3 discs:...
Page 38
Active Mode indicator TRK RPT RPT indicator The current (or lights up. FLDR RPT* and RPT indicators light up. DISC RPT and RPT All tracks/files of the indicators light up. * “FLDR RPT” is only applicable for MP3 disc. To play back only intros (Track Intro Scan/Folder Intro Scan/Disc Intro Scan) Press MODE to enter the...
EXTERNAL COMPONENT OPERATIONS Playing an external component You can connect the external component to the CD changer jack on the rear using the Line Input Adapter KS-U57 (not supplied). Preparations: • For connecting the Line Input Adapter KS-U57 and the external component, refer to the Installation/ Connection Manual (separate volume).
ADDITIONAL INFORMATION Sound modes (preset frequency level settings) The list below shows the preset frequency level settings for each sound mode. Sound Mode LEVEL FLAT HARD ROCK R&B JAZZ DANCE MUSIC COUNTRY REGGAE CLASSIC USER 1 USER 2 USER 3 Available characters You can use the following characters to assign names to station frequencies and CDs (both in this unit and in the CD changer).
What appears to be trouble is not always serious. Check the following points before calling a service center. Symptoms • Sound cannot be heard from the speakers. • This unit does not work at all. • SSM (Strong-station Sequential Memory) automatic preset does not work.
Page 42
Symptoms • Disc cannot be played back. • Noise is generated. • A longer readout time is required (“FILE CHECK” keeps flashing on the display). • Files cannot be played back as you have intended them to play. • Elapsed playing time is not correct.
Page 43
Symptoms • “NO DISC” appears on No disc is in the magazine. the display. Discs are inserted upside down. • “NO MAG” appears on No magazine is loaded in the the display. CD changer. • “RESET 8” appears on This unit is not connected to the the display.
MAINTENANCE Handling discs This unit has been designed to reproduce CDs, CD-Rs (Recordable), CD-RWs (Rewritable), and CD Texts. • This unit is also compatible with MP3 and WMA discs. How to handle discs When removing a disc from its case, press down the center holder of the case and lift the disc out, holding it by the edges.
AUDIO AMPLIFIER SECTION Maximum Power Output: Front: 50 W per channel Rear: 50 W per channel Continuous Power Output (RMS): Front: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. 19 W per channel into 4 Ω, 40 Hz to Rear: 20 000 Hz at no more than 0.8%...
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company • supplying kits. • If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Notes: • Replace the fuse with one of the specified • rating. If the fuse blows frequently, consult your JVC car audio dealer. • • It is recommended to connect to the speakers 50 W with maximum power of more than 50 W (both...
Page 49
ENGLISH !"#$ / Typical Connections / Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.
Page 50
!" !"#$%&'()%*+,-./ Front speakers !" You can connect another power amplifier for front speakers. !"#$%&'()*+,-./&0 Connecting cord supplied for your CD changer !"# = JVC CD changer JVC CD KD-G805 KD-G805 • KS-U57 * KD-G805 !" !"#$%&'() Firmly attach the ground wire to the metallic body or to the chassis of the car—...