Table of Contents
Advertisement
Quick Links
OWNER'S MANUAL
LG LED Signage
(LED SCREEN)
Please read the safety information carefully before using this product.
After reading this manual, keep it in an easily accessible location for future reference.
LSAA012-MX5
LSAA012-QX5
LSAA012-SX5
LSAA012-MX6
LSAA012-QX6
LSAA012-SX6
LSAA012-NX5
LSAA012-UX5
LSAA012-TX5
Copyright © 2022 LG Electronics Inc. All Rights Reserved.
LSAA012-NX6
LSAA012-UX6
LSAA012-TX6
www.lg.com
Advertisement
Table of Contents
Related Manuals for LG LSAA012-MX5
Summary of Contents for LG LSAA012-MX5
- Page 1 Please read the safety information carefully before using this product. After reading this manual, keep it in an easily accessible location for future reference. LSAA012-MX5 LSAA012-MX6 LSAA012-NX5 LSAA012-NX6 LSAA012-QX5 LSAA012-QX6 LSAA012-UX5 LSAA012-UX6 LSAA012-SX5 LSAA012-SX6 LSAA012-TX5 LSAA012-TX6 www.lg.com Copyright © 2022 LG Electronics Inc. All Rights Reserved.
-
Page 2: Table Of Contents
Screen ................15 - Remove Protective Bracket ........ 17 - Installation Precautions Guide ......19 - Installation Location ..........21 - Terminal ................. 23 CONNECTING LAN (LSAA012-MX5, LSAA012-QX5, LSAA012-MX6, LSAA012-QX6, LSAA012-NX5, LSAA012-UX5, LSAA012-NX6, LSAA012-UX6) ..........24 CONNECTING AC (LSAA012-MX5, LSAA012-MX6, LSAA012-NX5, LSAA012-NX6) .......... -
Page 3: Safety Precautions
SAFETY PRECAUTIONS The safety precautions are intended to prevent unexpected danger or harm by helping the user to use the product safely and for its intended purpose. WARNING If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION If you ignore the caution message, you may be slightly injured or the product may be damaged. -
Page 4: Precautions For The Ac Cable And Power
Precautions for the AC Cable and Power WARNING • Before using an AC cable, make sure it conforms to the national standards. • Operate the display only from a power source(i.e. voltage) indicated in the product specification. - Otherwise the product can be damaged, fire can occur or you may be electrocuted. If you are not sure what type of power supply you have, consult a certified installation company. - Page 5 • If water or any foreign substance enters the product, disconnect the AC cable immediately and contact the service centre. - Otherwise, this may cause a fire or electric shock due to damage to the product. • Keep the AC cable away from heating devices. - The cord coating may melt and cause fire or electric shock.
-
Page 6: Precautions For Moving The Product
Precautions for Moving the Product WARNING • Contact the service centre before moving the product. - It may cause electric shock and damage the product. • Make sure the product is turned off, unplugged, and all cables have been removed before the product is moved. - You may be electrocuted or the product can be damaged. -
Page 7: Precautions For Installing The Product
Precautions for Installing the Product WARNING • Contact the service centre before installing the product. - It can cause electric shock and damage the product. • Do not drop an object on or impact on the product. Keep out of reach of children and do not place toys or objects near the product to prevent throwing things on the product screen. - Page 8 CAUTION • Install the product where no Electromagnetic Interference occurs. • If you install the product in a place that does not meet the recommended conditions, this may cause serious damage to the product’s picture quality, life cycle, and appearance. Please check with service engineer before installing. Please do not install the product in places such as where there is an abundance of fine dust or oil mist, chemical substances are used, exposed to direct sunlight, the temperature is very high or low, the humidity is very high.
-
Page 9: Precautions For Cleaning The Product
Precautions for Cleaning the Product WARNING • Keep the product clean at all times. - If you don’t clean the unit for a long time and it becomes covered in dust, it can cause fire or product damage. • When you need to clean the inside of the product, you must contact the service centre. - Otherwise, cleaning without support may cause a fire, electric shock, or damage to the product. -
Page 10: Precautions For Using The Product
Precautions for Using the Product WARNING • Do not use the product in any environment with excessively high temperatures or humidity. • If you use the product for a long period of time, take a rest from time to time to protect your vision. - Extended viewing could result in impaired vision. - Page 11 • Do not use high voltage electrical goods near the product (e.g., a bug zapper). - This may result in product malfunction if it receives an electrical shock. • If there is a gas leak, do not touch the outlet, and open the windows for ventilation. - Otherwise, the product may cause fire or electric shock.
-
Page 12: Product Disposal
Product Disposal • Do not dispose of this product with general household waste. • Disposal of this product must be carried out in accordance to the regulations of your local authority. -
Page 13: Assembling And Preparing
ASSEMBLING AND PREPARING CAUTION • Always use genuine components to ensure safety and durability of the product. • The product warranty will not cover damage or injury caused by the use of unauthorised components. NOTE • The accessories provided with your product may vary depending on the model or region. •... -
Page 14: Optional Accessories
Without prior notice, optional accessories are subject to change to improve the performance of the product, and new accessories may be added. The illustrations in this manual may differ from the actual product and accessories. Middle Frame KT-BZ1080 Wall Mount WM-LC2 WM-LC3 WM-LC4 WM-LS2 WM-LS3 WM-LS4 Frame Jig WM-LG... -
Page 15: Handling For Protecting Led Package Screen
Handling for Protecting LED Package Screen When taking out the product, make sure the screen is not pressed. Protection Pad To stand the product upright, hold it on both sides so that the LED package screen does not touch the floor. LED Package Screen... - Page 16 Place the product with the LED package screen facing down. To protect the screen, lay the protective pad in the box on the floor. LED Package Screen Protection Pad If you do not have a pad, make sure that there is no foreign object on the floor when you lay the product on the floor, and then carefully place the LED package screen facing down or up.
-
Page 17: Remove Protective Bracket
Remove Protective Bracket Before installing the product, disassemble the protective brackets attached to each edge. M4 x L8 NOTE • Keep the protective brackets because you need them to move the product again. - Page 18 CAUTION If the product is tilted towards the LED package screen after the brackets on the corners are removed, the bottom of the product may be damaged. LED Package Screen If the product is tilted towards the edge of the LED package screen after the brackets on the corners are removed, the bottom (corner) of the product may be damaged.
-
Page 19: Installation Precautions Guide
Installation Precautions Guide Temperature • Make a cooling system for the enclosure so that the operating temperature of the product can be maintained. - Product operating temperature: 0 °C to 40 °C (the recommended room temperature is below 25 °C.) • Install in a location where the warm air from an air conditioner does not directly affect the product. - This will prevent malfunctions such as the screen turning off. - Page 20 Installation Position • Ensure the distance from the ceiling of the installation room to the product is at least 400 mm. - The high temperature air collected at the ceiling will naturally circulate to prevent malfunction. • Ensure the distance from the floor of the installation room to the product is at least 100 mm. - The air from the floor will easily circulate to the ceiling to prevent malfunctions. 400 mm or more 100 mm or more...
-
Page 21: Installation Location
Installation Location Installing on a Recessed Wall • After installation on a recessed wall, a bezel can be installed for interior purposes. A: 100 mm or more B: 25 mm or more C: 60 mm or more When Installing the Bezel • Ensure it can be detached for product repair. • For the top / bottom bezels, secure at least 60 % of the air vent to facilitate air circulation. - This will prevent malfunction. - Page 22 Installing on a Wall A: 100 mm or more B: 25 mm or more C: 60 mm or more...
-
Page 23: Terminal
Terminal LSAA012-MX5, LSAA012-MX6, LSAA012-NX5, LSAA012-NX6 LSAA012-QX5, LSAA012-QX6, LSAA012-UX5, LSAA012-UX6 • : Sends the IR signal to another set. • : Sends the LAN signal to another set. NOTE • The IR sensor is not provided with this product. • For CSAA-012X5, the IR sensor and remote control are provided. -
Page 24: Connecting Lan
CONNECTING LAN (LSAA012-MX5, LSAA012- QX5, LSAA012-MX6, LSAA012-QX6, LSAA012- NX5, LSAA012-UX5, LSAA012-NX6, LSAA012- UX6) You can connect to the CSAA-012X5 (System Controller) by using an LAN cable. LAN cable (*Not provided) CSAA-012X5 CAUTION • Check the direction so that the LAN cable is not damaged. -
Page 25: Connecting Ac (Lsaa012-Mx5, Lsaa012-Mx6, Lsaa012-Nx5, Lsaa012-Nx6)
CONNECTING AC (LSAA012-MX5, LSAA012- MX6, LSAA012-NX5, LSAA012-NX6) You can connect the unit to a power disconnecting device using an AC cable. • Use the AC cable to connect to the power disconnecting device. (Please use a cable that is long enough to be connected to the screen.) - Page 26 Country Live Neutral Ground Europe Brown Blue Green & Yellow North America Black White Green & Yellow India Black Green & Yellow Japan / Taiwan Black White Green & Yellow Korea Brown Blue Green & Yellow You can connect the AC cable connected to the power disconnecting device to the screen. Structure Fixing parts 100 mm...
-
Page 27: Troubleshooting
TROUBLESHOOTING No image is displayed. • Is the AC cable connected to the product? - Make sure the AC cable is properly connected to the power disconnecting device. • Is the ‘No Signal’ message displayed? - There is no connection between CSAA-012X5 and the input source. Check the connection status of the LAN cable. - Access the Input menu to check the input source. - Page 28 Without prior notice, the software is subject to change to improve the functionality of the product. • The above items are only applicable to the LSAA012-MX5, LSAA012-QX5, LSAA012-SX5, LSAA012-MX6, LSAA012-QX6, LSAA012-SX6, LSAA012-NX5, LSAA012-UX5, LSAA012-TX5, LSAA012-NX6, LSAA012-UX6, LSAA012-TX6 model. Please read “TROUBLESHOOTING” in the manual of CSAA-012X5.
-
Page 29: Product Specifications
PRODUCT SPECIFICATIONS Without prior notice, the product specifications are subject to change to enhance the functionality of the product. symbol means alternating current, and the symbol means direct current. LSAA012* Pixel pitch (distance between pixels) 1.25 mm Resolution 480 x 270 Pixel density 640,000 pixels/m Number of pixels per screen 129,600 pixels... - Page 30 LSAA012-MX5 Data connection Input/ Output ports Luminance Max 600 nit / Peak 1,200 nit Rating 100-240 V ~ 50/60 Hz 8.0 A Power consumption (Max.) 75 W/Cabinet, 370 W/m Power Consumption (for the normal use or video playback) 52 W/Cabinet, 255 W/m Dimensions (Width x Height x Depth) / Weight 600 mm x 337.5 mm x 44.9 mm / 7.3 kg LSAA012-QX5 Data connection Input/ Output ports Luminance Max 600 nit / Peak 1,200 nit...
- Page 31 LSAA012-QX6 Data connection Input/ Output ports Luminance Max 600 nit / Peak 1,200 nit Rating 100-240 V ~ 50/60 Hz 8.0 A Power consumption (Max.) 68 W/Cabinet, 332 W/m Power Consumption (for the normal use or video playback) 52 W/Cabinet, 255 W/m Dimensions (Width x Height x Depth) / Weight 600 mm x 337.5 mm x 44.9 mm / 7.3 kg LSAA012-SX6 Input/ Output ports Not Applied Luminance Max 600 nit / Peak 1,200 nit Rating 100-240 V ~ 50/60 Hz 8.0 A...
- Page 32 LSAA012-TX5 Input/ Output ports Not Applied Luminance Max 600 nit / Peak 1,200 nit Rating 100-240 V ~ 50/60 Hz 8.0 A Power consumption (Max.) 80 W/Cabinet, 397 W/m Power Consumption (for the normal use or video playback) 52 W/Cabinet, 255 W/m Dimensions (Width x Height x Depth) / Weight 600 mm x 337.5 mm x 44.9 mm / 7.7 kg LSAA012-NX6 Data connection Input/ Output ports Luminance Max 600 nit / Peak 1,200 nit Rating 100-240 V ~ 50/60 Hz 8.0 A...
- Page 33 Wireless Specification ASK (Amplitude Shift Keying) Frequency Range Output Power (Max. dBm e.i.r.p.) 57 GHz to 64 GHz • For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body. (Only Nigeria) Connection and use of this communications equipment is permitted by the Nigerian Communications Commission (Only India) Wireless Specification...
- Page 34 The model and serial number of the product are located on the back and on one side of the product. Record them below in case you ever need service. MODEL Temporary noise is normal when powering ON or OFF this device.