Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sharp 8M -B32C1
Summary of Contents for Sharp 8M -B32C1
- Page 1 8M-B32C1 Dismantle Instruction LCD MONITOR 8M-B32C1 MODEL Dismantle Instruction...
-
Page 2: Table Of Contents
8M-B32C1 Dismantle Instruction Table of contents 1. Scope........................3 2. Tools for dismantling ....................3 3. Dismantle Procedure ....................3 4. Stand, Back cover and PWB Plate ................4 5. Printed circuit boards ..................... 8 6. Battery ........................ 9 7. LCD Module ......................10 8. -
Page 3: Scope
8M-B32C1 Dismantle Instruction 1. Scope This document describes dismantling instruction according to Annex VII of Directive 2012/19/EU. 2. Tools for dismantling Below tools are required to dismantle this product. Screw Driver Nipper 3. Dismantle Procedure This product can be dismantled by below steps. 1. -
Page 4: Stand, Back Cover And Pwb Plate
8M-B32C1 Dismantle Instruction 4. Stand, Back cover and PWB Plate Stand can be removed with screw driver. Remove SCREW COVER SEAL on back cover. Then back cover can be removed with screw driver. - Page 5 8M-B32C1 Dismantle Instruction Cut the cable tie on VESA angle with nipper, and peel off ALPET SHEET and ALPET SHEET S. Then remove VESA angle with screw driver. (right side in back view) ALPET SHEET ALPET SHEET S...
- Page 6 8M-B32C1 Dismantle Instruction Detach the cables from DC switch PWB and remove the PWB with screw driver. Remove WIRING SHEET (Black PC sheet) from PWB Plate. Release all the cables that runs through the plate aperture. (cables from beneath the plate). DC switch PWB...
- Page 7 8M-B32C1 Dismantle Instruction Detach Key-FFC from the connector on Main I/F PWB Release from wire holders and remove the fixing tape on PWB Plate. Then PWB Plate can be removed with screw driver. (When the plate is lifted up, cables should go through the aperture of plate)
-
Page 8: Printed Circuit Boards
8M-B32C1 Dismantle Instruction 5. Printed circuit boards All PWBs can be removed by screw driver. Power PWB (1pcs) Main I/F PWB (1pcs) LED Driver PWB (2pcs) UCCT PWB (1pcs) DC switch PWB (1pcs) Connector PWB (1pcs) Varistor PWB (1pcs) T-CON PWB (1pcs) Key PWB (1pcs) -
Page 9: Battery
8M-B32C1 Dismantle Instruction 6. Battery This model uses only CR2032 Lithium Coin battery on Main I/F PWB. Battery CR2032 can easily be removed from the battery holder. -
Page 10: Lcd Module
8M-B32C1 Dismantle Instruction 7. LCD Module LCD Dismantle procedure... -
Page 11: Capacitors
8M-B32C1 Dismantle Instruction 8. Capacitors Electrolyte Capacitors which diameter/height is larger than 25mm is installed on Power PWB. These capacitors can be removed by using nipper to cut the leads. On Power PWB... -
Page 12: Parts List
8M-B32C1 Dismantle Instruction 9. Parts List Parts described in Annex VII of directive 2012/19/EU are as below. Parts Note 32inch LCD module Printed Circuit Boards Main I/F PWB Power PWB LED Driver PWB UCCT PWB DC switch PWB Connector PWB Key PWB Varistor PWB T-CON PWB...