Canopy kit for multi-passenger workman gtx utility vehicle (8 pages)
Summary of Contents for Toro 07389
Page 1
Electric Bed Lift Kit 2014 and After Workman ® MD/MDX/MDX-D Utility Vehicle Model No. 07389—Serial No. 315000001 and Up Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Outboard-lift bracket (short flanges) Inboard-lift bracket (long flanges) Install the bed bracket. Hex-head bolt (5/16 x 5-1/2 inches) Flange nut (5/16 inch) Switch Install the switch.
Pull the prop rod into the detent slot to secure the bed (Figure WARNING Preparing the Machine A raised bed could fall and injure persons that are working beneath it. • Always use the prop rod to hold the No Parts Required bed up before working under the bed.
Page 4
Align the left outboard-lift bracket (the bracket with the short flanges) to the outboard holes in the upper- and lower-bed braces (Figure Installing the Bed-Lift Brackets Parts needed for this procedure: Outboard-lift bracket (short flanges) Inboard-lift bracket (long flanges) Hex-head bolt (5/16 x 5-1/2 inches) Flange nut (5/16 inch) g025009 Figure 5...
Insert the hex-head bolt (5/16 x 5-1/2 inches) through hole 8 mm (5/16 inch) in the inboard-lift bracket (long flanges), bed structure, and the outboard bed-lift bracket (short flanges) as shown in Figure Installing the Switch Parts needed for this procedure: Switch Fuse (15 A)—machine serial number 411599999 and before only...
Page 6
Machine Serial Number 411600000 and After Cut out the opening in the dashboard decal for the switch (box A of Figure Install the switch connector through the opening in the dashboard (box B of Figure Install the switch to the switch connector (box C of Figure Ensure that the switch is oriented properly (box D of Figure...
Page 7
Connect the 2-socket electrical connector of the rear wire harness of the machine to the 2-pin connector of the lift actuator (Figure 10). Note: The 2-socket electrical connector of the Installing the Lift Actuator rear wire harness is located adjacent to the electrical-control cover.
Page 8
Press the up paddle the bed-lift switch to extend the rod of the lift actuator rod until the hole in the rod is aligns with the holes in the inboard and outboard-lift brackets (Figure 11). Removing the Prop Rod Note: Select the set of holes in the bracket for the gasoline and diesel machines;...
Maintenance Operation Servicing the Air Cleaner WARNING Driving the machine with the cargo bed raised For Workman MDX-D Machines could cause the machine to tip or roll easier. Support the bed with lifting equipment. You could damage the structure of the cargo bed if you operate the machine with the bed Remove the hairpin cotter and clevis pin raised.
Page 13
The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
Page 14
The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
Page 15
The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
Page 16
Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.