D-Link DIS-M100G-SW Quick Installation Manual

Q I
uick nstallation
Introduction
DIS-M100G-SW is a cost effective solution for the conversion between -
100 /1000 Base-T X and ( ) 100/1000 Base X interface it allows you to extend - ,
communication distance by optical fiber. DIS-M100G-SW
'
detection, so you don t need to use crossover wires. DIS-M100G-SW
～ ℃
operating temperature range from -40 70 and accepts a wide voltage range from
,
dual 12 ~ 48 VDC power inputs so it is suitable for harsh operating environments
Therefore, the DIS-M100G-SW is reliable media converter and can satisfy most
demand of operating environment.
Features
Supports 1 port 100/1000Base-T(X) auto-negotiation and auto-MDI/MDI-X
Support Ethernet to SFP port signal conversion
Provided DIP-Switch to set operation speed of SFP port
High reliability and rigid IP-30 housing
DIN-Rail and wall-mount enabled
Power Connection Guide
PWR2 PWR1
DC 12-48V
V2+ V2- V1+ V1-
V+
Power
V-
Supply
12-48 VDC V+ V-
Power
Supply
12-48 VDC
Installation
Din-Rail Install Step Wall-mounted Install Step
Q I G
DIS-M100G-SW
G
uide
Specifications
Model
supports MDI/MDIX auto
with wide
Physical Ports
.
100/1000 Base-T(X) Port in RJ45
Auto MDI/MDIX
100/1000Base-X SFP port
Technology
Ethernet standards
DIP-Switch 1/2
LED Indicators
Power indicator
100/1000Base-T(X) RJ45 port
indicator
100/1000Base-F(X) fiber port
indicator
Power
Input power
Power consumption(Typ.)
Overload current protection
Reverse polarity protection
Physical Characteristic
Enclosure
Dimension (W x D x H)
Weight (g)
Environmental
Storage Temperature
G
FrameGround
Operating Temperature
Operating Humidity
Regulatory Approvals
EMI
EMS
Shock
Free Fall
Vibration
Safety
Warranty
Accessory
4-Pin Terminal block
1
Screw (M3 X3)
4
Power Cable with power jack
7
Packing list
M o d l e n a m e
Gigabit Industrial Unmanaged Media Converter
DIS-M100G-SW with 1x100/1000Base-T(X) and 1x100/1000Base-X,
SFP socket
DIS-M100G-SW
1
1
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3x for Flow control
IEEE 802.3 ab for 1000Base-T
IEEE 802.3 z for 1000Base-X
DIP-Switch 1 (ON) and DIP-Switch 2 (ON) : SFP speed setting to 100Mbps
DIP-Switch 1 (OFF) and DIP-Switch 2 (OFF) : SFP speed setting to 1000Mbps
Green: Power LED x 2. (ON) power input on-line / (OFF) power input off-line
LED for Link/Act and Speed indicator :
Green on only : 1000Mbps Link/Act-(ON) Link up / (Flash) Acting /
(OFF) Link down
Green and Amber on : 100Mbps Link/Act-(ON) Link up / (Flash) Acting /
(OFF) Link down
*Note: If amber on only : Link up at 10Mbps is not a valid mode
Green for fiber port Link/Act - (ON) Link up / (Flash) Acting / (OFF) Link down
Dual 12~48 VDC power input at 4 pin terminal block
3.6 Watts
Present
Present
IP-30
26.1 (W) x 70 (D) x 95 (H)mm (1.03 x 2.76 x 3.74 inch)
190 g (0.42 lb)
-40 to 85 C (-40 to 185 F) o o
-40 to 70 C (-40 to 158 F) o o
5% to 95% Non-condensing
FCC Part 15, CISPR (EN55022) class A
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT),
EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
IEC60068-2-27
IEC60068-2-32
IEC60068-2-6
EN60950-1
5 years
Dust Cover (RJ-45) Dust Cover (SFP)
3
2
Wall-mounted kit 25mm DIN-Rail kit
6
5
QIG
8
M o d l e D e s c i r t p o i n A c c e s s o y r
X 1, X 1, X 1,
1 2 3 4
X 2, X 1, X 1,
5 6 7 8
Industrial Gigabit Ethernet to Fiber
Media Converter
Connections of Media converter
For long distance transmission
Working Status
Ethernet Port Status SFP Fiber Port Status
100Mbps 100Mbps
100Mbps 1000Mbps
1000Mbps
1000Mbps
1000Mbps 100Mbps
Front Panel
Power LED
Fiber Port LNK/ACT LED
SFP 100/1000Base-FX
Fiber Port
DIP Switch for Mode
Select
DIP-Switch
1000Base-T LNK/ACT
LED (Green)
100/1000Base-T(X)
LAN Port
10/100Base-T(X)
LNK/ACT LED (Amber)
Communication Connections
100Base-TX Ethernet Port Connection
RJ45 (8-pin, MDI) Port Pinouts RJ45 (8-pin, MDI-X) Port Pinouts
Pin Pin Single Pin
1 Tx+ 1
1 8
2 Tx- 2
3 Rx+ 3
6 Rx- 6
RJ45 (8-pin) to RJ45 (8-Pin) Straight-Through Cable Wiring
Straight-Through Cable
Switch Port
RJ-45 RJ45 Plug Pin1
Connector
Tx+ 3
Tx- 6
Rx+ 1
Rx- 2
RJ45 (8-pin) to RJ45 (8-Pin) Cross-Over Cable Wiring
Switch Port
Cross-Over Cable
(NIC Port)
RJ45 Plug Pin1
RJ-45
Connector
(Rx+) Tx+ 3
(Rx-) Tx- 6
(Tx+) Rx+ 1
(Tx-) Rx- 2
1000Base-T Ethernet Connection
RJ45 (8-pin, MDI) Port Pinouts RJ45 (8-pin, MDI-X) Port Pinouts
Pin P n i MDI P Pin n i
1 BI_DA+ 1 BI_DB+
1 8
2 BI_DA- 2 BI_DB-
3 BI_DB+ 3 BI_DA+
4 BI_DC+ 4 BI_DD+
5 BI_DC- 5 BI_DD-
6 BI_DB- 6 BI_DA-
7 BI_DD+ 7 BI_DC+
8 BI_DD- 8 BI_DC-
100/1000Base-X SFP Port Connection
LC-Port Pinouts
LC-Port to LC-Port Cable Wiring
Tx
Rx
Cable Wiring
X 8,
T x
X 1
Rx
Working status
Valid
Invalid
Valid
Invalid
DIP Switch Function
Description
SFP speed setting to 100Mbps
ON
OFF SFP speed setting to 1000Mbps
Single
Rx+
1 8
Rx-
Tx+
Tx-
NIC Port
RJ-45
Connector
3 Rx+
6 Rx-
1 Tx+
2 Tx-
Switch Port
(NIC Port)
RJ-45
Connector
1 Rx+ (Tx+)
2 Rx- (Tx-)
3 Tx+ (Rx+)
6 Tx- (Rx-)
M D - I X
1 8
LC-Port Pinouts
Rx
Tx
R x
Tx
Quick Installation Guide