ABB Relion 620 Series Manual
  1. Manuals
  2. Brands
  3. ABB Manuals
  4. Transformer
  5. Relion 620 Series
  6. Manual

ABB Relion 620 Series Manual

Transformer protection and control
Hide thumbs Also See for Relion 620 Series:
Table of Contents

Advertisement

Quick Links

®
Relion
620 series
Transformer Protection and Control
RET620
DNP3 Point List Manual

Advertisement

Table of Contents
loading

Related Manuals for ABB Relion 620 Series

Summary of Contents for ABB Relion 620 Series

  • Page 1 ® Relion 620 series Transformer Protection and Control RET620 DNP3 Point List Manual...
  • Page 3 Document ID: 1MRS757660 Issued: 2013-05-07 Revision: A Product version: 2.0 © Copyright 2013 ABB. All rights reserved...
  • Page 4 Copyright This document and parts thereof must not be reproduced or copied without written permission from ABB, and the contents thereof must not be imparted to a third party, nor used for any unauthorized purpose. The software or hardware described in this document is furnished under a license and may be used, copied, or disclosed only in accordance with the terms of such license.
  • Page 5 In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other than under explicit contractual commitments, in no event shall ABB be responsible or liable for any loss or damage resulting from the use of this manual or the application of the equipment.
  • Page 6 (EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB in accordance with the product standards EN 50263 and EN 60255-26 for the EMC directive, and with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive.

  • Page 7: Table Of Contents

    Table of contents Table of contents Section 1 Introduction...............9 This manual..................9 Intended audience................9 Product documentation...............9 Product documentation set............9 Document revision history............10 Related documentation..............10 Symbols and conventions..............10 Symbols..................10 Document conventions..............11 Functions, codes and symbols............12 Section 2 DNP3 data mappings.............19 Overview...................19 Supported functions................19 Binary inputs..................22 System functions.................22 CTRL.LLN0 Local/remote state (also present in DNP IIN-...
  • Page 8 Table of contents LD0.OLATCC1 On-load tap changer controller......28 Metering and measurand functions..........28 LD0.CMMXU1 Phase currents (1) limit supervision....28 LD0.CMMXU2 Phase currents (2) limit supervision....29 LD0.RESCMMXU1 Residual current limit supervision...29 LD0.RESCMMXU2 Residual current limit supervision...29 LD0.VMMXU1 Three-phase voltage limit supervision....29 LD0.RESVMMXU1 Residual voltage limit supervision...30 Protection functions..............30 LD0.LEDPTRC1 Global protection signals......30 LD0.TRPPTRC1 Global conditioning (1)........30...
  • Page 9 Table of contents LD0.PHPTOV1 Phase overvoltage protection - stage 1..34 LD0.PHPTOV2 Phase overvoltage protection - stage 2..34 LD0.PHPTOV3 Phase overvoltage protection - stage 3..35 LD0.ROVPTOV1 Residual overvoltage protection (1)...35 LD0.ROVPTOV2 Residual overvoltage protection (2)...35 LD0.ROVPTOV3 Residual overvoltage protection (3)...35 LD0.NSPTOC1 Negative-sequence overcurrent protection (1)................35 LD0.NSPTOC2 Negative-sequence overcurrent protection (2)................36...
  • Page 10 Table of contents LD0.LSHDPFRQ5 Load-shedding - instance 5......41 LD0.LSHDPFRQ6 Load-shedding - instance 6......41 Protection related functions............42 DR.RDRE1 Disturbance recorder..........42 LD0.SECRSYN1 Synchrocheck ..........42 LD0.CCRDIF1 Current circuit failure protection.....42 LD0.CCRDIF2 Current circuit failure protection.....42 LD0.CTSRCTF1 Current circuit supervision for transformers (1)..............42 LD0.SEQRFUF1 Fuse failure protection........43 Generic functions.................43 LD0.MAPGAPC1 Multipurpose analog protection function (1)................43...
  • Page 11 Table of contents LD0.SPCRGGIO1 Multipurpose binary outputs - status (1)...................48 LD0.FKEYGGIO1 LED states..........49 Physical and raw I/O data............50 LD0.XGGIO105 Physical I/O..........50 LD0.XHBGGIO105 Physical I/O..........50 LD0.XRGGIO105 Alarm/warning...........51 LD0.XBRGGIO130 Alarm/warning - physical outputs....51 LD0.XGGIO100 Physical I/O..........51 LD0.XGGIO110 Physical I/O..........51 Binary outputs...................52 System functions.................52 LD0.LLN0/LPHD1 Reset indications and LEDs, reset device..................52 LD0.DNPGGIO1 Parameter setting group control....53...
  • Page 12 Table of contents LD0.SRGAPC1 Multipurpose binary outputs - flip-flop resets (1)................59 LD0.SRGAPC2 Multipurpose binary outputs - flip-flop resets (2)................60 Analog inputs..................60 System functions.................60 CTRL.LLN0 Local remote station off........60 LD0.LPHD1 System values............61 LD0.LEDGGIO1 LHMI LED indications (3 states)....61 LD0.DNPGGIO1 Active parameter setting group....61 Switchgear functions..............62 CTRL.CBCSWI1 CB 4-pole (2 bit) position value....62 CTRL.CBCSWI2 CB 4-pole (2 bit) position value....62...
  • Page 13 Table of contents LD0.CMMXU2 Phase currents (2)..........66 LD0.CSMSQI1 Sequence of currents........66 LD0.RESCMMXU1 Residual current (1)........67 LD0.RESCMMXU2 Residual current (2)........67 LD0.VMMXU1 Voltage measurement ........67 LD0.RESVMMXU1 Residual voltage (1)........67 LD0.VSMSQI1 Sequence of voltage measurement....68 LD0.PEMMTR1 Power measurement and accumulated power values................68 Protection functions..............68 LD0.T2PTTR1 Temperature protection values (2)....68 Protected related functions............69 DR.RDRE1 Disturbance recorder values.......69...

  • Page 15: Section 1 Introduction

    Section 1 1MRS757660 A Introduction Section 1 Introduction This manual The point list manual describes the outlook and properties of the data points specific to the IED. The manual should be used in conjunction with the corresponding communication protocol manual. Intended audience This manual addresses the communication system engineer or system integrator responsible for pre-engineering and engineering for communication setup in a...

  • Page 16: Document Revision History

    1.3.2 Document revision history Document revision/date Product version History A/2013-05-07 First release Download the latest documents from the ABB Website http://www.abb.com/substationautomation. 1.3.3 Related documentation Name of the document Document ID DNP3 Communication Protocol Manual 1MRS757646 Symbols and conventions 1.4.1...

  • Page 17: Document Conventions

    Section 1 1MRS757660 A Introduction of a hazard which could result in corruption of software or damage to equipment or property. The information icon alerts the reader of important facts and conditions. The tip icon indicates advice on, for example, how to design your project or how to use a certain function.

  • Page 18: Functions, Codes And Symbols

    Section 1 1MRS757660 A Introduction 1.4.3 Functions, codes and symbols Table 1: RET620 functions, codes and symbols Function IEC 61850 IEC 60617 IEC-ANSI Protection Three-phase non-directional overcurrent protection, low stage, PHLPTOC1 3I> (1) 51P-1 (1) instance 1 Three-phase non-directional overcurrent protection, low stage, PHLPTOC2 3I>...
  • Page 19 Section 1 1MRS757660 A Introduction Function IEC 61850 IEC 60617 IEC-ANSI Three-phase undervoltage PHPTUV1 3U< (1) 27 (1) protection, instance 1 Three-phase undervoltage PHPTUV2 3U< (2) 27 (2) protection, instance 2 Three-phase undervoltage PHPTUV3 3U< (3) 27 (3) protection, instance 3 Three-phase overvoltage protection, PHPTOV1 3U>...
  • Page 20 Section 1 1MRS757660 A Introduction Function IEC 61850 IEC 60617 IEC-ANSI Circuit breaker failure protection, CCBRBRF2 3I>/Io>BF (2) 51BF/51NBF (2) instance 2 Three-phase inrush detector INRPHAR1 3I2f> (1) 68 (1) Master trip, instance 1 TRPPTRC1 Master Trip (1) 94/86 (1) Master trip, instance 2 TRPPTRC2 Master Trip (2)
  • Page 21 Section 1 1MRS757660 A Introduction Function IEC 61850 IEC 60617 IEC-ANSI Earthing switch position indication, ESSXSWI1 I <-> O ES (1) I <-> O ES (1) instance 1 Disconnector position indication, DCSXSWI3 I <-> O DC (3) I <-> O DC (3) instance 3 Disconnector position indication, DCSXSWI4...
  • Page 22 Section 1 1MRS757660 A Introduction Function IEC 61850 IEC 60617 IEC-ANSI Residual current measurement, RESCMMXU2 Io(B) (1) In(B) (1) instance 2 Three-phase voltage measurement VMMXU1 3U (1) 3V (1) Residual voltage measurement RESVMMXU1 Uo (1) Vn (1) Sequence voltage measurement VSMSQI1 U1, U2, U0 (1) V1, V2, V0 (1)
  • Page 23 Section 1 1MRS757660 A Introduction Function IEC 61850 IEC 60617 IEC-ANSI Generic control points, instance 1 SPCGGIO1 SPCGGIO (1) SPCGGIO (1) Generic control points, instance 2 SPCGGIO2 SPCGGIO (2) SPCGGIO (2) Generic control points, instance 3 SPCGGIO3 SPCGGIO (3) SPCGGIO (3) Remote Generic control points SPCRGGIO1 SPCRGGIO (1)

  • Page 25: Section 2 Dnp3 Data Mappings

    Section 2 1MRS757660 A DNP3 data mappings Section 2 DNP3 data mappings Overview This document describes the DNP3 data points and structures available in the IED. The data points are unmapped as a default on the DNP3 level. The point lists describe a superset of all DNP3 data available through the standard configuration/s including the optional functionalities.
  • Page 26 Section 2 1MRS757660 A DNP3 data mappings Function block TE201 DEFLPDEF2 ● DEFHPDEF1 ● NSPTOC1 ● NSPTOC2 ● ROVPTOV1 ● ROVPTOV2 ● ROVPTOV3 ● PHPTUV1 ● PHPTUV2 ● PHPTUV3 ● PHPTOV1 ● PHPTOV2 ● PHPTOV3 ● PSPTUV1 ● PSPTUV2 ● NSPTOV1 ●...
  • Page 27 Section 2 1MRS757660 A DNP3 data mappings Function block TE201 LSHDPFRQ2 ● LSHDPFRQ3 ● LSHDPFRQ4 ● LSHDPFRQ5 ● LSHDPFRQ6 ● CBXCBR1 ● CBXCBR2 ● DCXSWI1 ● DCXSWI2 ● ESXSWI1 ● DCXSWI3 ● DCXSWI4 ● ESXSWI2 ● DCSXSWI1 ● DCSXSWI2 ● ESSXSWI1 ●...

  • Page 28: Binary Inputs

    Section 2 1MRS757660 A DNP3 data mappings Function block TE201 PEMMXU1 ● LDPMSTA1 ● FMMXU1 ● RDRE1 ● ● = available in the device variant, o = optionally available in the device variant Binary inputs Table 3: Explanations of the binary input table columns Column name Description IEC 61850...

  • Page 29: Switchgear Functions

    Section 2 1MRS757660 A DNP3 data mappings 2.3.2 Switchgear functions 2.3.2.1 CTRL.Cxxxxx1 Circuit breaker (1) CB object and failure protection Table 6: CTRL.Cxxxxx1 Circuit breaker (1) CB object and failure protection IEC 61850 name SA name Description Values CTRL.CBCILO1 .EnaCls.stVal ENA_CLOSE Close enabled 1=Enabled...

  • Page 30: Ctrl.dxxxxx1 Controllable Disconnector (1)

    Section 2 1MRS757660 A DNP3 data mappings 2.3.2.3 CTRL.Dxxxxx1 Controllable disconnector (1) Table 8: CTRL.Dxxxxx1 Controllable disconnector (1) IEC 61850 name SA name Description Values CTRL.DCCILO1 .EnaCls.stVal ENA_CLOSE Close enabled 1=Enabled .EnaOpn.stVal ENA_OPEN Open enabled 1=Enabled .ItlByPss.stVal ITL_BYPASS Interlocking bypass 1=Bypassed CTRL.DCCSWI1 .Pos.stSeld...

  • Page 31: Ctrl.dxxxxx4 Controllable Disconnector (4)

    Section 2 1MRS757660 A DNP3 data mappings 2.3.2.6 CTRL.Dxxxxx4 Controllable disconnector (4) Table 11: CTRL.Dxxxxx4 Controllable disconnector (4) IEC 61850 name SA name Description Values CTRL.DCCILO4 .EnaCls.stVal ENA_CLOSE Close enabled 1=Enabled .EnaOpn.stVal ENA_OPEN Open enabled 1=Enabled .ItlByPss.stVal ITL_BYPASS Interlocking bypass 1=Bypassed CTRL.DCCSWI4 .Pos.stSeld...

  • Page 32: Sensors And Monitoring Functions

    Section 2 1MRS757660 A DNP3 data mappings 2.3.3 Sensors and monitoring functions 2.3.3.1 LD0.ARCSARC1 Fault arc protection stage 1 Table 14: LD0.ARCSARC1 Fault arc protection stage 1 IEC 61850 name SA name Description Values LD0.ARCSARC11 .FADet.stVal ARC_FLT_DET Arc detected 1=Detected LD0.ARCPTRC11 .Op.general OPERATE...

  • Page 33: Ld0.Sscbr2 Circuit-Breaker Condition Monitoring

    Section 2 1MRS757660 A DNP3 data mappings IEC 61850 name SA name Description Values .OpNumLO.stVal OPR_LO CB operations lockout 1=Lockout .PresAlm.stVal PRES_ALM Low pressure alarm 1=Alarm .PresLO.stVal PRES_LO Low pressure lockout 1=Lockout .SprChaAlm.stVal SPR_CHR_ALM Spring charge time alarm 1=Alarm 2.3.3.5 LD0.SSCBR2 Circuit-breaker condition monitoring Table 18: LD0.SSCBR2 Circuit-breaker condition monitoring...

  • Page 34: Automatic Control Functions

    Section 2 1MRS757660 A DNP3 data mappings 2.3.4 Automatic control functions 2.3.4.1 LD0.OLATCC1 On-load tap changer controller Table 21: LD0.OLATCC1 On-load tap changer controller IEC 61850 name SA name Description Values LD0.OLATCC1 .ParOp.stVal PARALLEL Parallel or single op. 1=Parallel .Auto.stVal AUTO Auto or manual op.

  • Page 35: Ld0.Cmmxu2 Phase Currents (2) Limit Supervision

    Section 2 1MRS757660 A DNP3 data mappings 2.3.5.2 LD0.CMMXU2 Phase currents (2) limit supervision Table 23: LD0.CMMXU2 Phase currents (2) limit supervision IEC 61850 name SA name Description Values LD0.CMMXU2 .HiAlm.stVal HIGH_ALARM High alarm 1=Alarm .HiWrn.stVal HIGH_WARN High warning 1=Warning .LoAlm.stVal LOW_ALARM Low alarm...

  • Page 36: Ld0.Resvmmxu1 Residual Voltage Limit Supervision

    Section 2 1MRS757660 A DNP3 data mappings 2.3.5.6 LD0.RESVMMXU1 Residual voltage limit supervision Table 27: LD0.RESVMMXU1 Residual voltage limit supervision IEC 61850 name SA name Description Values LD0.RESVMMXU1 .HiAlm.stVal HIGH_ALARM High alarm 1=Alarm .HiWrn.stVal HIGH_WARN High warning 1=Warning 2.3.6 Protection functions 2.3.6.1 LD0.LEDPTRC1 Global protection signals Table 28:...

  • Page 37: Ld0.Deflpdef1 Directional Earth-Fault Protection - Low Stage 1

    Section 2 1MRS757660 A DNP3 data mappings 2.3.6.4 LD0.DEFLPDEF1 Directional earth-fault protection - low stage 1 Table 31: LD0.DEFLPDEF1 Directional earth-fault protection - low stage 1 IEC 61850 name SA name Description Values LD0.DEFLPTOC1 Low stage (1) .Op.general OPERATE -Operate 1=Operate .Str.general START...

  • Page 38: Ld0.Eflptoc1 Non-Directional Earth-Fault And Sensitive Earth-Fault Protection - Low Stage 1

    Section 2 1MRS757660 A DNP3 data mappings 2.3.6.9 LD0.EFLPTOC1 Non-directional earth-fault and sensitive earth-fault protection - low stage 1 Table 36: LD0.EFLPTOC1 Non-directional earth-fault and sensitive earth-fault protection - low stage 1 IEC 61850 name SA name Description Values LD0.EFLPTOC1 Low stage (1) .Op.general OPERATE...

  • Page 39: Ld0.Phhptoc1 Phase Overcurrent Protection - High Stage 1

    Section 2 1MRS757660 A DNP3 data mappings 2.3.6.13 LD0.PHHPTOC1 Phase overcurrent protection - high stage 1 Table 40: LD0.PHHPTOC1 Phase overcurrent protection - high stage 1 IEC 61850 name SA name Description Values LD0.PHHPTOC1 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start...

  • Page 40: Ld0.Phlptoc2 Phase Overcurrent Protection - Low Stage 2

    Section 2 1MRS757660 A DNP3 data mappings 2.3.6.18 LD0.PHLPTOC2 Phase overcurrent protection - low stage 2 Table 45: LD0.PHLPTOC2 Phase overcurrent protection - low stage 2 IEC 61850 name SA name Description Values LD0.PHLPTOC2 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start...

  • Page 41: Ld0.Phptov3 Phase Overvoltage Protection - Stage 3

    Section 2 1MRS757660 A DNP3 data mappings 2.3.6.23 LD0.PHPTOV3 Phase overvoltage protection - stage 3 Table 50: LD0.PHPTOV3 Phase overvoltage protection - stage 3 IEC 61850 name SA name Description Values LD0.PHPTOV3 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start 2.3.6.24 LD0.ROVPTOV1 Residual overvoltage protection (1)

  • Page 42: Ld0.Nsptoc2 Negative-Sequence Overcurrent Protection (2)

    Section 2 1MRS757660 A DNP3 data mappings 2.3.6.28 LD0.NSPTOC2 Negative-sequence overcurrent protection (2) Table 55: LD0.NSPTOC2 Negative-sequence overcurrent protection (2) IEC 61850 name SA name Description Values LD0.NSPTOC2 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start 2.3.6.29 LD0.NSPTOV1 Negative-sequence overvoltage protection - stage 1 Table 56: LD0.NSPTOV1 Negative-sequence overvoltage protection - stage 1 IEC 61850 name...

  • Page 43: Ld0.Phptuv3 Phase Undervoltage Protection - Stage 3

    Section 2 1MRS757660 A DNP3 data mappings 2.3.6.33 LD0.PHPTUV3 Phase undervoltage protection - stage 3 Table 60: LD0.PHPTUV3 Phase undervoltage protection - stage 3 IEC 61850 name SA name Description Values LD0.PHPTUV3 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start 2.3.6.34 LD0.PSPTUV1 Positive-sequence undervoltage protection - stage 1...

  • Page 44: Ld0.Frpfrq2 Frequency Protection (2)

    Section 2 1MRS757660 A DNP3 data mappings IEC 61850 name SA name Description Values .Op.general OPR_UFRQ -Operate 1=Operate LD0.FRPFRC1 Frequency gradient .Op.general OPR_FRG -Operate 1=Operate 2.3.6.38 LD0.FRPFRQ2 Frequency protection (2) Table 65: LD0.FRPFRQ2 Frequency protection (2) IEC 61850 name SA name Description Values LD0.FRPTRC2...

  • Page 45: Ld0.Hrefpdif2 High-Impedance Restricted Earth-Fault Protection (2)

    Section 2 1MRS757660 A DNP3 data mappings 2.3.6.41 LD0.HREFPDIF2 High-impedance restricted earth-fault protection (2) Table 68: LD0.HREFPDIF2 High-impedance restricted earth-fault protection (2) IEC 61850 name SA name Description Values LD0.HREFPDIF2 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start 2.3.6.42 LD0.LREFPDIF1 Low-impedance restricted earth-fault protection (1) Table 69:...

  • Page 46: Ld0.Tr2Pdif1 Transformer Differential Protection

    Section 2 1MRS757660 A DNP3 data mappings 2.3.6.46 LD0.TR2PDIF1 Transformer differential protection Table 73: LD0.TR2PDIF1 Transformer differential protection IEC 61850 name SA name Description Values .Blk2HSt.general BLKD2H 2nd harmonic res blocking 1=Blocking .Op.general OPERATE General operate 1=Operate 2.3.6.47 LD0.T2PTTR1 Thermal protection (2) Table 74: LD0.T2PTTR1 Thermal protection (2) IEC 61850 name...

  • Page 47: Ld0.Lshdpfrq3 Load-Shedding - Instance 3

    Section 2 1MRS757660 A DNP3 data mappings 2.3.7.3 LD0.LSHDPFRQ3 Load-shedding - instance 3 Table 77: LD0.LSHDPFRQ3 Load-shedding - instance 3 IEC 61850 name SA name Description Values LD0.LSHDPTRC3 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start .RestLodOp.general RESTORE Restore the load 1=Restore .RestLodStr.general...

  • Page 48: Protection Related Functions

    Section 2 1MRS757660 A DNP3 data mappings 2.3.8 Protection related functions 2.3.8.1 DR.RDRE1 Disturbance recorder Table 81: DR.RDRE1 Disturbance recorder IEC 61850 name SA name Description Values DR.RDRE1 .RcdMade.stVal DR recording made 1=Made 2.3.8.2 LD0.SECRSYN1 Synchrocheck Table 82: LD0.SECRSYN1 Synchrocheck IEC 61850 name SA name Description...

  • Page 49: Ld0.Seqrfuf1 Fuse Failure Protection

    Section 2 1MRS757660 A DNP3 data mappings 2.3.8.6 LD0.SEQRFUF1 Fuse failure protection Table 86: LD0.SEQRFUF1 Fuse failure protection IEC 61850 name SA name Description Values LD0.SEQRFUF1 .Str.general FUSEF_U General start 1=Start .Str3Ph.general FUSEF_3PH Three-phase start 1=Start 2.3.9 Generic functions 2.3.9.1 LD0.MAPGAPC1 Multipurpose analog protection function (1) Table 87: LD0.MAPGAPC1 Multipurpose analog protection function (1)

  • Page 50: Ld0.Mapgapc5 Multipurpose Analog Protection Function (5)

    Section 2 1MRS757660 A DNP3 data mappings 2.3.9.5 LD0.MAPGAPC5 Multipurpose analog protection function (5) Table 91: LD0.MAPGAPC5 Multipurpose analog protection function (5) IEC 61850 name SA name Description Values LD0.MAPGAPC5 .Op.general OPERATE Stage operate 1 = Operate .Str.general START Stage start 1 = Start 2.3.9.6 LD0.MAPGAPC6 Multipurpose analog protection function (6)

  • Page 51: Ld0.Mapgapc10 Multipurpose Analog Protection Function (10)

    Section 2 1MRS757660 A DNP3 data mappings 2.3.9.10 LD0.MAPGAPC10 Multipurpose analog protection function (10) Table 96: LD0.MAPGAPC10 Multipurpose analog protection function (10) IEC 61850 name SA name Description Values LD0.MAPGAPC10 .Op.general OPERATE Stage operate 1 = Operate .Str.general START Stage start 1 = Start 2.3.9.11 LD0.MAPGAPC11 Multipurpose analog protection function (11)

  • Page 52: Ld0.Mvgapc2 Multipurpose Binary Inputs (2)

    Section 2 1MRS757660 A DNP3 data mappings 2.3.9.14 LD0.MVGAPC2 Multipurpose binary inputs (2) Table 100: LD0.MVGAPC2 Multipurpose binary inputs (2) IEC 61850 name SA name Description Values LD0.MVGAPC2 .Q1.stVal Input 1 signal 0/1=Off/On .Q2.stVal Input 2 signal 0/1=Off/On .Q3.stVal Input 3 signal 0/1=Off/On .Q4.stVal Input 4 signal...

  • Page 53: Ld0.Spcggio1 Multipurpose Binary Outputs - Status (1)

    Section 2 1MRS757660 A DNP3 data mappings 2.3.9.17 LD0.SPCGGIO1 Multipurpose binary outputs - status (1) Table 103: LD0.SPCGGIO1 Multipurpose binary outputs - status (1) IEC 61850 name SA name Description Values LD0.SPCGGIO1 .SPCS01.stVal Output 1 state 0/1=Off/On .SPCS02.stVal Output 2 state 0/1=Off/On .SPCS03.stVal Output 3 state...

  • Page 54: Ld0.Spcggio3 Multipurpose Binary Outputs - Status (3)

    Section 2 1MRS757660 A DNP3 data mappings IEC 61850 name SA name Description Values .SPCS14.stVal Output 14 state 0/1=Off/On .SPCS15.stVal Output 15 state 0/1=Off/On .SPCS16.stVal Output 16 state 0/1=Off/On 2.3.9.19 LD0.SPCGGIO3 Multipurpose binary outputs - status (3) Table 105: LD0.SPCGGIO3 Multipurpose binary outputs - status (3) IEC 61850 name SA name Description...

  • Page 55: Ld0.Fkeyggio1 Led States

    Section 2 1MRS757660 A DNP3 data mappings IEC 61850 name SA name Description Values .SPCS09.stVal Output 9 state 0/1=Off/On .SPCS10.stVal Output 10 state 0/1=Off/On .SPCS11.stVal Output 11 state 0/1=Off/On .SPCS12.stVal Output 12 state 0/1=Off/On .SPCS13.stVal Output 13 state 0/1=Off/On .SPCS14.stVal Output 14 state 0/1=Off/On .SPCS15.stVal...

  • Page 56: Physical And Raw I/O Data

    Section 2 1MRS757660 A DNP3 data mappings 2.3.10 Physical and raw I/O data 2.3.10.1 LD0.XGGIO105 Physical I/O Table 108: LD0.XGGIO105 Physical I/O IEC 61850 name SA name Description Values LD0.XGGIO105 .Ind1.stVal X105-Input 1 1/0=ON/OFF .Ind2.stVal X105-Input 2 1/0=ON/OFF .Ind3.stVal X105-Input 3 1/0=ON/OFF .Ind4.stVal X105-Input 4...

  • Page 57: Ld0.Xrggio105 Alarm/Warning

    Section 2 1MRS757660 A DNP3 data mappings 2.3.10.3 LD0.XRGGIO105 Alarm/warning Table 110: LD0.XRGGIO105 Alarm/warning IEC 61850 name SA name Description Values LD0.XRGGIO105 .Alm.stVal XRGGIO105 Alarm 1=Alarm .Wrn.stVal XRGGIO105 Warning 1=Warning 2.3.10.4 LD0.XBRGGIO130 Alarm/warning - physical outputs Table 111: LD0.XBRGGIO130 Alarm/warning - physical outputs IEC 61850 name SA name Description...

  • Page 58: Binary Outputs

    Section 2 1MRS757660 A DNP3 data mappings IEC 61850 name SA name Description Values .Ind5.stVal X110-Input 5 1/0=ON/OFF .Ind6.stVal X110-Input 6 1/0=ON/OFF .Ind7.stVal X110-Input 7 1/0=ON/OFF .Ind8.stVal X110-Input 8 1/0=ON/OFF .SPCSO1.stVal X110-Output 1 1/0=ON/OFF .SPCSO2.stVal X110-Output 2 1/0=ON/OFF .SPCSO3.stVal X110-Output 3 1/0=ON/OFF .SPCSO4.stVal X110-Output 4...

  • Page 59: Ld0.Dnpggio1 Parameter Setting Group Control

    Section 2 1MRS757660 A DNP3 data mappings 2.4.1.2 LD0.DNPGGIO1 Parameter setting group control Table 116: LD0.DNPGGIO1 Parameter setting group control IEC 61850 name SA name Description Type LD0.DNPGGIO1 .ActSG1.ctlVal Setting group 1 .ActSG2.ctlVal Setting group 2 .ActSG3.ctlVal Setting group 3 .ActSG4.ctlVal Setting group 4 .ActSG5.ctlVal...

  • Page 60: Ctrl.dccswi3 Controllable Disconnector (3) Control

    Section 2 1MRS757660 A DNP3 data mappings 2.4.2.5 CTRL.DCCSWI3 Controllable disconnector (3) control Table 121: CTRL.DCCSWI3 Controllable disconnector (3) control IEC 61850 name SA name Description Type CTRL.DCCSWI3 .Pos.Oper.ctlVal Disconnector control On/Off 2.4.2.6 CTRL.DCCSWI4 Controllable disconnector (4) control Table 122: CTRL.DCCSWI4 Controllable disconnector (4) control IEC 61850 name SA name...

  • Page 61: Ld0.Sscbr2 Reset Signals Of Cb Condition Monitoring

    Section 2 1MRS757660 A DNP3 data mappings 2.4.3.2 LD0.SSCBR2 Reset signals of CB condition monitoring Table 126: LD0.SSCBR2 Reset signals of CB condition monitoring IEC 61850 name SA name Description Type LD0.SSCBR2 .RsAccAPwr.Oper.ctlVal RST_IPOW Reset accum. energy .RsCBWear.Oper.ctlVal RST_CB_WEAR Reset CB life and op. counter .RsSprChaTm.Oper.ctlVal RST_SPR_T Reset spring charge alarm...

  • Page 62: Ld0.Lshdpfrq3 Loadshedding Controls (3)

    Section 2 1MRS757660 A DNP3 data mappings 2.4.5.3 LD0.LSHDPFRQ3 Loadshedding controls (3) Table 130: LD0.LSHDPFRQ3 Loadshedding controls (3) IEC 61850 name SA name Description Type LD0.LSHDPTRC3 .ManRest.Oper.ctlVal MAN_RESTORE Manual restore .BlkRest.Oper.ctlVal BLK_REST Cancel restore 2.4.5.4 LD0.LSHDPFRQ4 Load shedding controls (4) Table 131: LD0.LSHDPFRQ4 Load shedding controls (4) IEC 61850 name...

  • Page 63: Generic Functions

    Section 2 1MRS757660 A DNP3 data mappings 2.4.7 Generic functions 2.4.7.1 LD0.SPCGGIO1 Multipurpose binary outputs (1) The binary outputs can be configured either as pulse- or persistent-type outputs. Pulse- type outputs are triggered with the write value "1". Persistent-type outputs can be written with both values "1"...

  • Page 64: Ld0.Spcggio3 Multipurpose Binary Outputs (3)

    Section 2 1MRS757660 A DNP3 data mappings IEC 61850 name SA name Description Type .SPCS04.ctlVal Output 4 control On/Off .SPCS05.ctlVal Output 5 control On/Off .SPCS06.ctlVal Output 6 control On/Off .SPCS07.ctlVal Output 7 control On/Off .SPCS08.ctlVal Output 8 control On/Off .SPCS09.ctlVal Output 9 control On/Off .SPCS10.ctlVal...

  • Page 65: Ld0.Spcrggio1 Multipurpose Binary Outputs (1)

    Section 2 1MRS757660 A DNP3 data mappings 2.4.7.4 LD0.SPCRGGIO1 Multipurpose binary outputs (1) The binary outputs can be configured either as pulse- or persistent-type outputs. Pulse- type outputs are triggered with the write value "1". Persistent-type outputs can be written with both values "1" and "0". The setting mode "toggled" for local operation corresponds to "persistent"...

  • Page 66: Ld0.Srgapc2 Multipurpose Binary Outputs - Flip-Flop Resets (2)

    Section 2 1MRS757660 A DNP3 data mappings 2.4.7.6 LD0.SRGAPC2 Multipurpose binary outputs - flip-flop resets (2) Table 140: LD0.SRGAPC2 Multipurpose binary outputs - flip-flop resets (2) IEC 61850 name SA name Description Type LD0.SRGAPC2 .Rs1.ctlVal Reset flip-flop 1 .Rs2.ctlVal Reset flip-flop 2 .Rs3.ctlVal Reset flip-flop 3 .Rs4.ctlVal...

  • Page 67: Ld0.Lphd1 System Values

    Section 2 1MRS757660 A DNP3 data mappings 2.5.1.2 LD0.LPHD1 System values Table 143: LD0.LPHD1 System values IEC 61850 name SA name Description Values Arg 1,2,3,4 LD0.LPHD1 .NumCmpChg.stVal Num.of comp. changes 0…65535 0,65535,0,65535 .NumPwrUp.stVal Num.of power ups 0…65535 0,65535,0,65535 .PhyHealth1.stVal Warning Warning code 0…65535 0,65535,0,65535...

  • Page 68: Switchgear Functions

    Section 2 1MRS757660 A DNP3 data mappings 2.5.2 Switchgear functions 2.5.2.1 CTRL.CBCSWI1 CB 4-pole (2 bit) position value Table 146: CTRL.CBCSWI1 CB 4-pole (2 bit) position value IEC 61850 name SA name Description Values Arg 1,2,3,4 CTRL.CBCSWI1 Intermediate=0; Off=1; On=2; .Pos.stVal POSITION Bad=3...

  • Page 69: Ctrl.dcsxswi4 Disconnector 4, 4-Pole (2 Bit) Position Values

    Section 2 1MRS757660 A DNP3 data mappings 2.5.2.6 CTRL.DCSXSWI4 Disconnector 4, 4-pole (2 bit) position values Table 151: CTRL.DCSXSWI4 Disconnector 4, 4-pole (2 bit) position values IEC 61850 name SA name Description Values Arg 1,2,3,4 CTRL.DCSXSWI4 Intermediate=0; Off=1; On=2; .Pos.stVal POSITION Bad=3 0…3...

  • Page 70: Ctrl.essxswi1 Earth Switch 1, 4-Pole (2 Bit) Position Values

    Section 2 1MRS757660 A DNP3 data mappings 2.5.2.11 CTRL.ESSXSWI1 Earth switch 1, 4-pole (2 bit) position values Table 156: CTRL.ESSXSWI1 Earth switch 1, 4-pole (2 bit) position values IEC 61850 name SA name Description Values Arg 1,2,3,4 CTRL.ESSXSWI1 Intermediate=0; Off=1; On=2; .Pos.stVal POSITION Bad=3...

  • Page 71: Sensors And Monitoring Functions

    Section 2 1MRS757660 A DNP3 data mappings 2.5.3 Sensors and monitoring functions 2.5.3.1 LD0.SSCBR1 Circuit-breaker condition monitoring values Table 160: LD0.SSCBR1 Circuit-breaker condition monitoring values IEC 61850 name SA name Description Values Arg 1,2,3,4 LD0.SSCBR1 .AccAPwrPhA.mag Iyt value, phase A 0…1e6 0,1E6,0,1E6 .AccAPwrPhB.mag...

  • Page 72: Ld0.Tpossltc1 Tap Changer Position Value

    Section 2 1MRS757660 A DNP3 data mappings 2.5.3.3 LD0.TPOSSLTC1 Tap changer position value Table 162: LD0.TPOSSLTC1 Tap changer position value IEC 61850 name SA name Description Values Arg 1,2,3,4 LD0.TPOSSLTC1 .TapPos.valWTr.posVal TAP_POS Tap changer position -64…63 -64,63,-64,63 2.5.4 Metering and measurand functions 2.5.4.1 LD0.CMMXU1 Phase currents (1) Table 163:...

  • Page 73: Ld0.Rescmmxu1 Residual Current (1)

    Section 2 1MRS757660 A DNP3 data mappings 2.5.4.4 LD0.RESCMMXU1 Residual current (1) Table 166: LD0.RESCMMXU1 Residual current (1) IEC 61850 name SA name Description Values Arg 1,2,3,4 LD0.RESCMMXU1 .A.res.instCVal.mag I0_INST Residual current 0.00..40.0 [xIn] 0,40,0,4000 2.5.4.5 LD0.RESCMMXU2 Residual current (2) Table 167: LD0.RESCMMXU2 Residual current (2) IEC 61850 name...

  • Page 74: Ld0.Vsmsqi1 Sequence Of Voltage Measurement

    Section 2 1MRS757660 A DNP3 data mappings 2.5.4.8 LD0.VSMSQI1 Sequence of voltage measurement Table 170: LD0.VSMSQI1 Sequence of voltage measurement IEC 61850 name SA name Description Values Arg 1,2,3,4 LD0.VSMSQI1 Sequence of voltages 0.00…4.00 .SeqV.c1.cVal.mag I1_DB -Positive magnitude [xUn] 0,4,0,400 0.00…4.00 .SeqV.c2.cVal.mag I2_DB...

  • Page 75: Protected Related Functions

    Section 2 1MRS757660 A DNP3 data mappings 2.5.6 Protected related functions 2.5.6.1 DR.RDRE1 Disturbance recorder values Table 173: DR.RDRE1 Disturbance recorder values IEC 61850 name SA name Description Values Arg 1,2,3,4 DR.RDRE1 .FltNum.stVal Number of recordings 0…65535 0,65535,0,65535 .MemUsed.stVal Rec. memory used 0…100 [%] 0,100,0,100 2.5.6.2...

  • Page 76: Ld0.Xbrggio130 Rtd Inputs

    Section 2 1MRS757660 A DNP3 data mappings 2.5.7.2 LD0.XBRGGIO130 RTD inputs Table 176: LD0.XBRGGIO130 RTD inputs IEC 61850 name SA name Description Values Arg 1,2,3,4 LD0.XBRGGIO130 -10000… .AnIn1.instMag AI_VAL1 RTD input 1 10000 -1E4,1E4,-1E4,1E4 -10000… .AnIn2.instMag AI_VAL2 RTD input 2 10000 -1E4,1E4,-1E4,1E4 -10000…...

  • Page 77: Section 3 Dnp3 Protocol Implementation

    Implementation table and the point list tables, provides a complete configuration/interoperability guide for communicating with a device. Table 177: Device profile document DNP3 device profile document Vendor name: ABB Oy Device name: RET620 Highest DNP level supported: Device function: For requests: Level 2+ ○...
  • Page 78 Section 3 1MRS757660 A DNP3 protocol implementation DNP3 device profile document ○ Sometimes ● Configurable as: "Only when reporting event data", or "When reporting event data or multi-fragment messages" Timeouts while waiting for: Data link ○ None ○ Fixed at ____ ○...

  • Page 79: Dnp3 Implementation Table

    Section 3 1MRS757660 A DNP3 protocol implementation DNP3 device profile document ○ Configurable ○ When device restarts ○ Only certain objects ○ When status flags change ○ Sometimes (attach explanation) ○ ENABLE/DISABLE UNSOLICITED No other options are permitted. function codes supported Default counter object/variation: Counters roll over at: ●...
  • Page 80 Section 3 1MRS757660 A DNP3 protocol implementation Table 178: Implementation table OBJECT REQUEST (Library will parse) RESPONSE (Library will respond with) Object Variation Function codes Qualifier codes number number Description Function codes (dec) Qualifier codes (hex) (dec) (hex) Binary 1 (read) 00, 01 (start-stop) input –...
  • Page 81 Section 3 1MRS757660 A DNP3 protocol implementation OBJECT REQUEST (Library will parse) RESPONSE (Library will respond with) 16-bit 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop) 2 (default) analog 06 (no range, or all) 17, 28 (index) input 07, 08 (limited qty) 17, 28 (index) 32-bit...
  • Page 82 Section 3 1MRS757660 A DNP3 protocol implementation OBJECT REQUEST (Library will parse) RESPONSE (Library will respond with) Time delay 129 (response) 07 (limited qty) fine (qty = 1) Not defined Class 0 1 (read) 06 (no range, or all) data Class 1 1 (read) 06 (no range, or all)

  • Page 83: Section 4 Glossary

    Section 4 1MRS757660 A Glossary Section 4 Glossary Application function block library CROB Control relay output block Common time of occurrence. The time and date CTO object is an information object that represents the absolute time of day. DNP3 A distributed network protocol originally developed by Westronic.
  • Page 88 Contact us ABB Oy Medium Voltage Products, Distribution Automation P.O. Box 699 FI-65101 VAASA, Finland Phone +358 10 22 11 +358 10 22 41094 www.abb.com/substationautomation...

This manual is also suitable for:

Ret620

Table of Contents