Advertisement
Quick Links
INTRODUCTION
Before operating this projector, please read this manual carefully and completely. This manual will provide you
with the basic instructions for operation of the projector. Installation, preliminary adjustments and procedures
which require the opening of the projector and contact with electrical components should be performed by
service personnel. For continued safe and reliable operation, use only cables supplied by the manufacturer for
power. Adhere to all notes and warnings.
Features
Multi scan circuit automatically locks on video, superdata from 15kHz to 61.lkHz (MultiSync 6PG) and
graphics signals from 15kHz to 90kHz (MultiSync 9PG). You can interface video and high resolution RGB
signals from various computers, workstations and graphics boards.
7" CRTs with deflection angle 90 degrees produce a detailed picture with a resolution of 1280 x 1024
pixels.
Impregnated cathode used in the CRTs makes possible 800 lumens of light output.
ECP lens produces an image with true color reproduction.
AKB circuit provides a stable white balance.
The wide band video circuit provides of 70MHz of Video Bandwidth.
Display size can be altered to accommodate any picture size from 60" to 300" diagonal. In addition to
ceiling mounting, floor, desk top and rear installations are possible.
Digital point convergence provides high accuracy for a projecting fine graphic displays. (This can be
purchased as an optional item for the MultiSync 6PG)
Easy accessing of adjustment item with on-screen menus.
Accepts up to 100 inputs with the ISS-6OlO/ISS-6OlOG.
Video system compatible with NTSC, PAL, SECAM and NTSC 4.43.
Up to 100 convergence patterns can be stored in the stand alone mode in digital memory.
Quick copy convergence for fast easy set up from one preset signal.
Built in self diagnostics for on sight troubleshooting.
Built in "CROSS HAIR", "CROSS HATCH", "DOT", "WINDOW" and "H (FOCUS)" test patterns for
accurate setup.
Source information status display.
The SEQUENCER function allows the projector to automatically select input signals one after another.
1
Advertisement
Related Manuals for NEC PG-6000
Summary of Contents for NEC PG-6000
- Page 1 INTRODUCTION Before operating this projector, please read this manual carefully and completely. This manual will provide you with the basic instructions for operation of the projector. Installation, preliminary adjustments and procedures which require the opening of the projector and contact with electrical components should be performed by service personnel.
-
Page 2: Important Safeguards
Installation Place the projector on a flat, level surface and in a dry area free from dust and moisture. Do not place the projector in direct sunlight, near stoves or other heat radiating appliances. -
Page 3: Part Names And Functions
1. POWER Switch (Main power) Press to turn the main power on. The STANDBY indicator is lit. In this condition you can start up the projector by pressing the POWER ON button on the remote control or the POWER button on the rear panel. - Page 4 PART NAMES AND FUNCTIONS Control panel on the rear 11. POWER Button Turns the projector on or off when the projector is in the standby condition (Main Power switch on and Standby indicator lit). 12. CONTROL Button Used with other buttons. similar to a shift key on a typewriter or computer.
- Page 5 PART NAMES AND FUNCTIONS Remote control unit User Remote Control RC-6010 Full Function Remote Control RC-6011 NOTE: The full function remote control is designed for setup adjustment. Use the user remote control for normal operation.
- Page 6 PART NAMES AND FUNCTIONS 1. POWER Buttons (ON/OFF) Press the ON button to turn the projector on when the projector is in the standby condition. (STANDBY indicator lit). Press the OFF button to return the projector to the standby condition.
- Page 7 PART NAMES AND FUNCTIONS LINEARITY CONV Button Press to enter the LINEARITY CONVERGENCE mode. You can adjust the horizontal and the vertical linearity convergence for the red or blue CRT. Pressing with CTL button controls the LINEAR- BALANCE convergence. KEY STONE ALIGN Button Press to enter the KEY STONE ALIGNMENT mode.
- Page 8 PART NAMES AND FUNCTIONS Battery installation and replacement User remote control Press down on the battery compartment cover and slide the cover in the direction of the arrow. 2. Install the two new batteries, making sure that their polarity matches the (+) (-) diagrams inside the battery compartment.
-
Page 9: Basic Operation
6) To turn off the power, press the POWER OFF button on the remote control or the POWER button on the rear panel. 7) Press the POWER switch on the front terminal to turn off the main power of the projector. 8) Last, turn off the connected equipment power. - Page 10 This could damage the CRTs. NOTE: The explanation of the operation on the following pages is for use with the remote control. You can also operate the projector using the buttons on the control panel of the projector. PICTURE menu...
- Page 11 BASIC OPERATION Picture Adjustment To adjust the picture for each input, proceed as follows: NOTE: The Color, Sharpness, and Tint controls are not included in the “PICTURE” menu for RGB signal. The Tint control is not included in the “PICTURE” menu for SECAM/PAL signal.
- Page 12 BASIC OPERATION 6. Use the CURSOR t or u button to select either “YES” or “NO” and press the ENTER button. Will be returned to the source screen. Items to select • YES………..The data will be stored • NO…………The data will not be stored To exit this mode without storing the current status, select "NO".
- Page 13 BASIC OPERATION Position Adjustment Adjust the position and screen area Proceed as follows: 1. Press the OPERATE button. The "operate" menu will be displayed 2. Use the CURSOR por q button to highlight the "2/POSI- TION" line. Press the ENTER button to display the “POSI- TION’...
- Page 14 BASIC OPERATION When selecting BLANKING: 1) Hold down the CTL button and press CURSOR buttons to choose the right, left, top or bottom edge. The marker on the selected side will turn to a solid color. 2) Adjust the blanking using the CURSOR buttons. Top (U) and Right (R)--------- Pressing por u increases.
- Page 15 BASIC OPERATION Sound Adjustment (only when used with the ISS-6010/ISS-6010G) Adjust the volume to your preference. Proceed as follows: 1. Press the OPERATE button. The “OPERATE” menu will be displayed. 2. Use the CURSOR p or q button to highlight the "3/ SOUND”...
- Page 16 BASIC OPERATION Input Selection You can switch from one input to any other input signal Proceed as follows: 1. Press the OPERATE button. The “OPERATE” menu will be displayed. 2. Use the CURSOR p or q button to highlight the "4/INPUT SELECT"...
- Page 17 When pressing any one of the INPUT buttons to directly access one signal among two or more of the same signals, the projector will output the signal listed in the upper line automatically. To select the one listed in the lower line, use the CURSOR p or q button and press the ENTER button.
- Page 18 BASIC OPERATION Source Information This is for viewing the signal information and the current status of various setting. Proceed as follows: 1. Press the OPERATE button. The “OPERATE” menu will be displayed. 2. Use the CURSOR por q button to highlight the "5/ SOURCE INFO"...
- Page 19 BASIC OPERATION Static Convergence Adjustment Adjust for the red and blue CRTs to place their pattern on top of the green test pattern (center only). NOTE: The static convergence adjustment should be per- formed for R and B CRT. Carry out the adjustment after dis- playing a motion picture for 20 minutes or more.
- Page 20 BASIC OPERATION 8. Use the CURSOR t or u button to select either “YES” or “NO” and press the ENTER button. If the STATIC convergence data has not been changed, the “STORE ?" menu will not be displayed. Items to select •...
- Page 21 BASIC OPERATION Picture and Sound Mute This function mutes a picture or sound. To mute a picture or sound: Pressing PICTURE (PIC) MUTE mutes a picture. Pressing SOUND MUTE motes sound. Pressing again restores the picture (or sound). NOTE: When picture is muted, no “OPERATE” menu or “ADJUST’...
-
Page 22: Specifications
: Less than 0.2% of V-height Warm up time : 20 minutes Setup signal : Cross hairs, Cross hatch. Dot, Window pattern, H test pattern Power supply : AC 120V 60Hz (PG6000/PG-9000) AC 220-240V 50Hz (PG6000G/PG-9000G) Power consumption : PG-6000.PG-6000G 430W PG-9000/PG-9000G 500W Input current : 5.8A (AC 120V) PG-6000/6.7A (AC 120V) PG-9000... - Page 23 1) This works only for VIDEO signals. 2) This works only for NTSC video signals. 3) This works only with the Switcher operation. Specifications are subject to change without notice. The dimensions given for the projector do not include protruding parts.
- Page 24 Consult your dealer for changing the on-screen display mode. If the main power is not supplied to the projector for three days or more, the built-in clock may have to be reset, If this happens, consult your dealer for setting date and time.