Table of Contents
Advertisement
➟➟➟Continued
How to Set up
The following describes the procedures from opening the package to starting
using this console drawer. Be sure to follow these procedures.
Step 1
Checking components
Open the package, and then make sure you have all the components listed below:
● User's Guide (CD-ROM) x1
● Getting Started (this guide)
● Cable clamp x2
● VGA cable (1.8 m)
*
● DVI cable (1.8m)
* Do not use a DVI cable (1.8m) in Taiwan. This product is certified
as Information Technology Equipment not as Audio/Video Products.
● USB cable (1.8 m)
● Guide rails (left and right)
● Set screws x10
Step 2
Installation
Installation of Rack
Use the console drawer by installing it on a standard EIA 19-inch rack
assembly.
Install a rack to a site where satisfies the following conditions. Then,
install the console drawer on the rack.
Refer to
Chapter 2, Preparations "Installation of
Tips
Rack", "Installing Console Drawer on Rack", and
"Installing the Console Drawer"
Safety Precautions
Before starting setup,
be sure to read "Safety precautions" and "Safety notes" of
"Precautions of Use (Be Sure to Read)" in the "User's Guide",
and then correctly set up the console drawer following the described
Room that satisfies the
following conditions: *
<While operating>
Temperature: 5 to 45℃
Humidity: 10 to 85%
Close enough to connect the
power cord to power outlet or
UPS.
100 to 240 Vac parallel bi-
polar wall power outlet with
the ground line, or UPS
Install the rack on a flat and
rigid floor.
* If the console drawer is installed in high temperature area and you do not need to use console feature,
store the console drawer in rack during operation.
１． When installing guide rails, the guides must
face forward and inward. (Put front spacer in
front side of the rack, and put rear spacer in
back side of the rack.) Insert
the projection portion of rear
spacer of guide rails into
rack support holes. (See ①)
２． Secure the holes at the top
and bottom of rear spacer with
screws from the outside of
rack support.(See ②)
３． Mount guide rails inside rack
support in front side, and
secure the upper and lower
holes with screws. (See ③)
in User's Guide.
• Do not disconnect/connect the plug while your hands are wet.
Failure to follow this warning may cause an electric shock.
• Do not touch any part of the server and console drawer
including the cables when a thunderstorm is approaching. There
notes.
may be a risk of electric shock from lightning strike.
• Do not disassemble, repair, or modify the server and console
drawer.
Allow clearance of at least 1 m in
front and behind, 60 cm in left and
right, and 40 cm in height.
If several racks are to be used,
anchor them.
The rack must be
fixed with stabilizers.
Rear spacer
Rack support for the rear
Rack support for the front
Rear of
the rack
②
①
Guide rail
Set
screws
Set screws
Front spacer
①
Guide rail
Guide for
②
guide rails
Rear
spacer
Rear spacer
Front spacer
Set screws
②
Set
screws
Set
③
screws
③
Front of
the rack
Rack support for
the rear
Front spacer
Rack support for the front
(Installation of Guide Rails)
• Do not install the server and console drawer in dusty, humid,
oily, or fuming place and in a place exposed to direct
sunlight.
• Use a grounded outlet with the specified voltage.
• Do not connect many cords into a single outlet by using
extension cords.
4.
From the front of the
guide rail, insert the
console drawer along with
the rail.（Step ④ in the
figure below）
5. Push in the console
Guide rail
drawer until it stops,
and secure the front of
the unit with screws.
（Step ⑤ in the figure
below）
Make sure that the console drawer not to interfere the
Note
devices set up and down of the console drawer.
Make sure that the console drawer not to interfere the
devices set up and down of the console drawer when the
console is pulled out or storing into the rack.
If the console drawer still interfere the other devices,
change the position of the console drawer. (For example,
leaving 1U space.)
Step 3
Connecting cables
Cable connection Procedures
Notes on connecting cables
Important
•
Turn off the console drawer, server, and peripheral
devices before connecting cables. If one of them is
running when connected, a malfunction or failure may
occur.
•
When you connect the connector of VGA cable or DVI cable,
Set screws
firmly secure the connector with screws to console drawer
and the server. Loose cable connection may cause the
screen display to be shifted or not to appear.
③
Refer to
Chapter 2, Preparations "Cable Connection
Tips
"Preventing cables to be pulled off"
Guide rail
④
Latch lever
Set screw
⑤
" and
in User's Guide.
Advertisement
Table of Contents
