Page 1 Thank You For Using TheServiceManualShop.com SERVICE MANUAL Large Format Color Inkjet Printer EPSON Stylus Pro 10000/10000CF/10600 SEIJ00020 Thank You For Using TheServiceManualShop.com...
Page 2 The contents of this manual are subject to change without notice. All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them.
Page 3 ACCESSING INTERNAL COMPONENTS. Do not replace imperfectly functioning components with components which are not manufactured by Epson. If second source IC or other components which have not been approved are used, they could cause damage to the Epson product, or could void the warranty offered by Epson.
Page 4 Thank You For Using TheServiceManualShop.com Safety Information To prevent accidents during a maintenance procedure, strictly observe the Warnings and Cautions. Do not do anything that is dangerous or not within the scope of this document. Do not do anything that is dangerous even if not specifically described in this manual. In addition to the descriptions below and those given in this manual, there are many situations and circumstances that are dangerous.
Page 5 It may also provide additional information that is Provides preventive maintenance procedures and the related to a specific subject, or comment on the results lists of Epson-approved lubricants and adhesives achieved through a previous action. required for servicing the product.
Page 6 Thank You For Using TheServiceManualShop.com Revision Status Revision Issued Date Description March 30, 2001 First Release Chapter 1 1.1:Throughput of semiglossy photo paper revised. 1.1:"PS server" deleted. Tables of exclusive paper deleted. 1.1.1: Ink cartridge code corrected. Specification paper description revised. 1.2: Nozzle number for color revised.
Page 7 Thank You For Using TheServiceManualShop.com Revision Status Revision Issued Date Description Revision up: [Chapter-4] Table 4-5 "C362DRV Board Connectors" on page 137 November 5, 2003 (Connection from CN19/20/21/22/23/24 is corrected.) [Chapter-7] Table 7-1 "C362DRV Board Connectors" on page 280 (Same as above) Thank You For Using TheServiceManualShop.com...
Page 8: Table Of Contents
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table of Contents Chapter 1 Product Description 1.5 Operating Panel Messages ................33 1.6 SelecType Settings .................... 35 1.1 Features ....................... 6 1.6.1 Printer Setting Menu .................. 36 1.1.1 Consumable Products & Options ..............7 1.6.2 Test Print Menu ..................
Page 9 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 3.1.2 Troubleshooting practice ................80 4.3.2.3 C362MAIN Board Removal ..........135 4.3.2.4 Board ASSY CSIC Removal ..........136 3.2 Troubleshooting Using the Error Messages ........... 81 4.3.2.5 C362DRV Board Removal ..........137 3.2.1 Status Reply Priority ..................
Page 10 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.2.1 Head Rank Input ..................190 5.4.4.6 Test report for dot missing detector ........231 5.2.2 Parameter Backup ..................190 5.4.4.7 A13 slant adjustment ............232 5.2.3 Firmware Download ................193 5.4.4.8 A123 slant adjustment ............
Page 11 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 6.1 General Maintenance Issues ................266 6.1.1 Periodic Maintenance Items ..............267 6.1.2 Product Life Information ................. 267 6.1.3 Printing output at the time of maintenance ..........268 6.2 Maintenance inspection items ..............271 Chapter 7 Appendix 7.1 Wiring Diagrams ....................
Page 12: Chapter 1 Product Description
Thank You For Using TheServiceManualShop.com C H A P T E R PRODUCT DESCRIPTION Thank You For Using TheServiceManualShop.com...
Page 13: Features
Compatibility with Stylus Pro 9000/ Stylus Pro 7000/ Stylus Pro 7500 Commands are upper compatible with Stylus Pro 9000 / Stylus Pro 9500 / Stylus The EPSON Stylus Pro 10000/10000CF is the ultra high picture quality B0+ size Pro 7000 / Stylus Pro 7500...
Page 14: Consumable Products & Options
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.1.1 Consumable Products & Options Table 1-2. Consumable products & Options (continued) Name Code Product Table 1-2. Consumable products & Options Rip Station 5100 PS EAI - C850092 Fiery Adobe® PostScript® 3™ Server...
Page 15: Specifications
1.2.2 Character Specifications Character code: 1.2.1 Print Specifications English several character expansion graphics (PC437) Multilingual (PC850) Printing : Inkjet Type style: an EPSON original type style Nozzle configuration English several character Courier Black - 180 nozzles Control code: Color - 900 nozzles (cyan, magenta, yellow, light cyan, light magenta, 180...
Page 16: Paper
Specifications 2"core: 210~1118mm (W) x ~45m (H) (within roll size) The printer accepts following plain paper and EPSON special paper. It is not 3"core: 210~1118mm (W) x ~202m (H) (within roll size) assured feeding and print quality with any other paper except them.
Page 17: Sheet
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.2.4.2 Sheet Plain paper It is assured feeding only with following specifications. Specifications Paper Size : Following list The printer accepts following plain paper and special paper. It is not assured feeding and print quality with any other paper except them.
Page 18 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com NOTE: Special paper Table 1-6. Exclusive paper Media Size Supporting Media List Sheet Roll Paper Super 210m 329m 22" 24" 36" 44" A3/B 210x2 216x2 297x4 279x4 329x4 420x5...
Page 19 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 1-6. Exclusive paper Premium Semigloss Photo Paper Photo Grade Glossy Paper(except US) Photo Glossy Paper (US) Photo Grade Semigloss Paper (except US) Photo Semigloss Paper (US) Premium Luster Photo...
Page 20: Printable Area
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.2.4.3 Printable area The list and figure shown below. Table 1-7. Heading Roll Paper Cut Sheets PW (width) 210 ~1118mm 210 ~ 1118mm PL (length) Max. 202m 279~1580mm LM (left margin)
Page 21: Paper Set Lever
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.2.5 Paper set lever 1.2.6 Ink Cartridge When the paper set lever is pulled to the front, paper is released. Pigment / Dye ink cartridge When the paper set lever is pushed down to the back, paper is fixed, and it...
Page 22 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Figure 1-2. Ink Cartridge Physical Specifications 500ml Thank You For Using TheServiceManualShop.com Product Description Specifications...
Page 23: Electrical Specification
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.2.7 Electrical specification 1.2.8 Controller Rated voltage AC 100 ~ 240V Hitachi SH7709A, 120MHz Input voltage range Code ROM AC 90 ~ 264V Rated frequency range Font ROM 50 ~ 60Hz...
Page 24: Safety Approvals
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.2.9 Safety approvals 1.2.12 Reliability 120Vversion Total print volume Safety standard 20,000 pages (B0, 720x360 FOL, Bi-D) : UL1950 Print head life 28 billion shot / nozzle : CSA22.2 No.950...
Page 25: Environmental Conditions
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.2.14 Environmental Conditions 1.2.14.2 Vibration & Shock See the following table. 1.2.14.1 Temperature/Humidity Table 1-10. Vibration and Shock See the following table. Vibration Shock Condition Notes Table 1-9. Environmental Conditions...
Page 26: Cutting Specification
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.2.15 Cutting Specification Table 1-11. Cut condition and Cut method Cut condition Cut method There are two methods to cut a roll paper, automatic and manual cut. Manual cut after forward feed Paper is fed for L1 length and cut in 4 steps.
Page 27: Physical Specification
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.2.16 Physical Specification Dimensions of Unit (mm): 1865 (W) x 1225 (H) x 710 (D) Weight: 132Kg (including the stand) Figure 1-4. Dimensions of Unit 1 Thank You For Using TheServiceManualShop.com...
Page 28: Interfaces
Revision D Thank You For Using TheServiceManualShop.com 1.3 Interfaces The EPSON Stylus Pro 10000/10000CF is equipped with parallel and USB interfaces as well as an expansion slot for an optional Type-B interface. This section provides information on each of these interfaces.
Page 29 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Connector pin assignment and signals are shown below. Table 1-13. Connector Pin Assignments and signals (Compatibility Mode) Pin No. Signal Name Return GND Pin In/Out* Functional Description -STROBE Data reception pulse. Data is read at the falling edge of this pules.
Page 30 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Data Transmission Timing NIBBLE MODE Table 1-15. Transmission Specifications DATA data byte n data byte n+ 1 Description hold Transmission mode IEEE-1284 nibble mode -STROBE next Synchronization Refer to IEEE-1284 specification...
Page 31 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 1-16. Connector Pin Assignments - Nibble Mode Pin No. Signal Name Return GND Pin In/Out* Functional Description HostClk Host clock signal. DATA0 DATA1 DATA2 The DATA0 through DATA7 signals represent data bits 0 to7, respectively.
Page 32 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com ECP MODE Table 1-17. Transmission Specifications Description Transmission mode IEEE-1284 ECP mode Synchronization Refer to IEEE-1284 specification Handshaking Refer to IEEE-1284 specification Signal level IEEE-1284 level 1 device Adaptable connector See forward channel Data trans.
Page 33 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 1-18. Connector Pin Assignments - ECP Mode Pin No. Signal Name Return GND Pin In/Out* Functional Description HostClk In Data or address information are transferred from a host to a printer.
Page 34: Usb
Data encoding : NRZI MT48p,PW127cl10cpi,PRG(T0xxxx.yyyy.zzzz)rev,SPD0fast AP1200ma Adaptable connector : USB series B Product name: Stylus Pro 10000 (pigment: Stylus Pro 10000CF) Suggested cable length : 2 meters Emulation type: ESCPL2-00 Entity type: EPSONLQ2J Table 1-19. USB connector pin assignments and signals Card in Type-B slot 2: Pin no.
Page 35: Complement Item
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.3.4 Complement Item INITIALIZATION There are three kinds of initialization method. PREVENTION HOSTS FROM DATA TRANSFER TIME-OUT Power-on initialization When data is received from the parallel interface or the type B interface while no error This printer is initialized when turning the printer power on.
Page 36 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com DEFAULT SETUP VALUES Default setup values are as follows. The parameters for items which may be saved for panel setup, default setup, and remote commands are used as default values.
Page 37: Operating Panel
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.4 Operating Panel BUTTONS AND FUNCTIONS Each button on the operating panel and their functions are described below. This section describes the operating panel, the buttons, the lights, and the way you make settings.
Page 38 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com LEDS Table 1-21. LED Indicator Lights Status Condition • On • Printer power ON. Operate • Blink • Printer processing data, or in power OFF sequence. • On • Paper out, end of roll, Paper mismatch error, paper set...
Page 39: Indicator Status In Normal Mode
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.4.1 Indicator Status in Normal Mode Table 1-24. Pause Indicator Printer Status Indicator Table 1-22. Operate Indicator Print ready Printer Status Indicator In SelecType mode With power on and in any status other than those listed below.
Page 40 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.5 Operating Panel Messages Table 1-27. Operating Panel Messages (continued) Display Message Meaning Printer status and error messages appear on the operating Panel display. The table Waiting for paper initialize start trigger PRESS PAUSE BUTTON below lists the messages.
Page 41 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 1-27. Operating Panel Messages (continued) Display Message Meaning When total dots fired = 90%, cartridge enters near-end INK LOW condition. Remaining ink = A1 at 100% duty Printer requires maintenance - see “Maintenance MAINTENANCE REQ.
Page 42: Selectype Settings
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.6 SelecType Settings Operation The SelecType menus are displayed in turn each time the "SelecType" button is Entering SelecType mode pressed in the SelecType menu select mode. The setup menu is displayed right- justified on the LCD.
Page 43: Printer Setting Menu
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.6.1 Printer Setting Menu PLATEN GAP Selecting this mode allows the user to set the platen gap. The relationship between Table 1-29. Printer Setting Menu panel setting, command setting (SN command), and actual platen gap position is...
Page 44 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com INTERFACE SELECT DETECT SKEW ERROR Selecting this mode allows selection of the parallel / USB, or optional interface-1 / It restrains "PAPER NOT STRAIGHT" error and keeps printing by PAPER NOT 2, or automatic interface selection.
Page 45: Test Print Menu
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.6.2 Test Print Menu 1.6.2.2 Status sheet Table 1-31. Test Print Menu Display Message Item Notes Check the printout, any missing lines mean the NOZZLE CHECK PRINT nozzle(s) are clogged.
Page 46: Printer Status Menu
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.6.3 Printer Status Menu Table 1-32. Printer Status Menu Items LCD panel display Values Table 1-32. Printer Status Menu F E, F *E, F **E, F ***E, F ****E,...
Page 47 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com CUTTER LIFE MONITOR CR MOTOR LIFE MONITOR How to calculate: How to calculate: Calculate with cumulative total of cutting times. (Reference value: 2000 times) It is calculated for trouble examination / obstacle prevention in case that it is used Counter is cleared with changing cutter.
Page 48 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com PF MOTOR LIFE MONITOR HEAD UNIT LIFE MONITOR How to calculate: How to calculate: PF roller life and driven roller life are calculated with total paper feeding (Reference The numbers of dot injection for each color are added up, the number of injecting...
Page 49: User Paper Setup Menu Items
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.6.4 User Paper Setup Menu Items Table 1-40. Paper Setup Menu Utilization of this mode enables user defined paper to be used by registering optimum Items LCD panel display...
Page 50: Cutter Replacement Menu
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.6.5 Cutter Replacement Menu This mode is used to replace the cutter and clear the cutter life counter. The setting method is shown below. Select the cutter replacement menus from the panel.
Page 51: Gap Adjustment
<Setup> Set the paper in place. Select the gap adjustment menu from the panel. Set to ’STD’ when using EPSON paper (0.2mm or 1.2mm thick). For other paper, Figure 1-12. Gap Ajustment print pattern set thickness in units of 0.1mm.
Page 52: Maintenance Mode 1
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.7 Maintenance Mode 1 Startup The maintenance mode display is selected by switching power ON while pressing the Pause button. 1.7.1 Outline Operation The Setup items select mode is selected by pressing the Item button once. The first...
Page 53 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 1-44. Maintenance Mode 1 Setup Items HEXADECIMAL DUMP Item Panel display Setup value The hex dump function allows data sent to the printer to be printed and displayed in...
Page 54 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 1-46. Information Recorded in CSIC SELECTABLE M/W SETTING (EGC: FROM T01717) Item Panel display Setup value Description Set the most suitable value of irregular M/W for each printer, and banding will...
Page 55: Maintenance Mode 2
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.8 Maintenance Mode 2 Termination Switch power OFF > ON. Maintenance mode 2 setup items : Refer to the following table. The following explanations regarding operating Panel service C A U T I O N functions are for service and support purposes only;...
Page 56 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 1-50. Counter initialize menu Initialize RTC Item Panel display Setup value Selecting this mode allows the user to set RTC initialized time to NVRAM. Initialize NVRAM, timer, life The panel display is following;...
Page 57 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Initialize ink capacity CSIC detection level Selecting this mode allows the user to initialize the ink capacity counter. Selecting this mode allows the user to adjust CSIC detection level. Each adjustment value indicates as following;...
Page 58 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com M/W7 balance M/W 7 Balance is a mode for individual adjustment of the feeding amount for each pass during printing and is available only when Mode C has been selected by "MW 7 Mode Selection"...
Page 59: Jumper Settings
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 1.9 Jumper Settings The factory default settings for jumper and DIP switch on the Drive Board (C362DRV) are as follows. SWD2 SWD1 Jumper Setings C362DRV SWD1 1234 JP1 : OPEN...
Page 60: Chapter 2 Operating Principles
Thank You For Using TheServiceManualShop.com C H A P T E R OPERATING PRINCIPLES Thank You For Using TheServiceManualShop.com...
Page 61: Description
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.1 Description This section explains the print mechanism and operating principles for the EPSON Stylus Pro 10000/10000CF. The hardware block is shown in Figure 2-1. 28 ｘ 6 Front Cover_R CR Home...
Page 62 Revision D Thank You For Using TheServiceManualShop.com The description of the hardware that showed in Figure 2-1 is shown in Table 2-1. Table 2-1. Major Components of Stylus Pro 10000/10000CF/10600 Name Function outline,etc. • 32 bit CPU, control program (Firmware inside the FLASH ROM) and memory (DRAM) etc. are being contained.
Page 63: Printer Mechanism Components
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.2 Printer Mechanism Components The printer mechanism of EPSON Stylus Pro 10000/10000CF consists of the following mechanism parts. Table 2-2. Printer mechanism Drive Reference Name Mounting location Type Explanation...
Page 64 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Drive Reference Name Mounting location Type Explanation Function / control / others voltage clause PF roller is revolved via the belt slowing- The revolution of the motor is controlled...
Page 65 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Drive Reference Name Mounting location Type Explanation Function / control / others voltage clause The C362DRV board makes the pump motor It detects whether the pressure by the pump...
Page 66 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Drive Reference Name Mounting location Type Explanation Function / control / others voltage clause It discharges the air from the flushing duct Ink that delivered it with the dot missing...
Page 67: Carriage Device Section
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.2.1 Carriage device section The block diagram of carriage structure is shown below. The unique mechanism is composed on the carriage, to carry out movement/printing to, Steel belt the printing area (= the carriage migration area) of width with stable/high precision 44 inches the B0 form in this machine.
Page 68 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com The explanation of the sensor that is used in carriage migration department is as CARRIAGE MOVEMENT SECTION follows. It is the structure that loaded the carriage on the CR guide rail of the aluminum CR_HP sensor extrusion corner pipe through the four bearings.
Page 69 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com P_Edge sensor It is being attached on the left side of the carriage and detect the lag (the size of the skew) of the width and the head of the form with reflection style the photo interrupter.
Page 70 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com PLATEN GAP ADJUSTMENT SECTION guide the carriage (=head) mounting location always needs to keep regular distance to the rail space for printing precision maintenance. In this printer, as the gap between the form printing face and also head nozzle face become regular according to paper thickness, the print head nozzle face is variable structure.
Page 71 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com P_EDGE (paper width detection) the sensor This sensor is installed to the carriage left back. Detecting the top edge location (the degree of the skew) of paper right and left edge location and sense paper width and also skew determination.
Page 72 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Cutter solenoid / cutter It is being attached to the carriage left side and cut roll paper. The cut paper is carried out, by pushing down the cutter, while accompanying the movement of the carriage.
Page 73: Paper Feed Section
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.2.2 Paper feed section Paper set lever sensor A unique paper feed is being composed, to carry out the high precision paper feed of Paper set lever Suction motor the roll paper and cut sheet by friction feed in this machine.
Page 74 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Shutter position Sub platen The shutter position is switched by the paper loading position as following; Table 2-3. Shutter Shutter Paper position Closed Start print - 40mm printing from top of form...
Page 75 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com The explanation of the sensor that is used in paper feed department is as follows. P_THICK sensor Using the photo-interrupter, it is attached to the H top cover right side. The sensor P_FRONT sensor lever has a pressure/subordinate roller assembly.
Page 76 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Paper set lever detector Using the transparency style photograph sensor, it is attached to the lower part of the paper control set lever. The sensor detection lever is to paper control lever actuation the structure that interlocks.
Page 77: Cleaning Device Section
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.2.3 Cleaning device section The structure of the cleaning unit is shown in the next figure. Cleaning device department is built to a certain cleaning unit on the right the main Cleaning unit frame.
Page 78 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Cap assembly (drive with the cap motor) Doing print head nozzle capping at the time of unactuation and ink fill/cleaning actuation. Head cleaner Thank You For Using TheServiceManualShop.com Operating Principles...
Page 79: Dot Missing Detector / Flushing Box
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.2.4 Dot missing detector / Flushing box Dot missing detector Dot missing detector irradiates the detection device on the diagonal line with the Dot missing detector is on the left side of a cleaning unit and detect the abnormality of laser light emitting diode and be detecting the ink discharge condition from each ink discharge from the print head nozzle (dot lacking etc.) with the laser light.
Page 80: Ink Pump Assy
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.2.5 Ink pump Assy It is in the right edge of a main frame and be attached to I/S frame. There is the device that deliver compressed air to the ink cartridge and locks the carriage.
Page 81: Ink Supply Device Section
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.2.6 Ink supply device section The flow of the ink is as follows. Print head Assy Ink pump Assy Ink holder / ink cartridge It is the structure that attaches each ink cartridge of K, C, M, Lc, Lm, Y (from left side) Print head total 6 color to ink holder (I/H) on the right side of the printer in this machine.
Page 82: Others
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.2.7 Others CIRCUIT BOARD PLACEMENT COVER SENSOR There are the panel unit on surface right of this printer, and Power supply circuit board The cover sensor switch is attached in cover open and close department, to detect the...
Page 83: C362Main Board
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.3 C362MAIN board Table 2-6. C362MAIN board main integrated circuit explanation Name Location Function The C362 MAIN board does the interface control with the host computer. The HJFK • Serial EEPROM board is installed to connector CN2 standard.
Page 84: C362Drv Board Description
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.4 C362DRV board description The block diagram of this control circuit is shown below. NOTE: As for each circuit detail, refer to "the C362DRV board circuit figure" of Explaining about the actuation description of the C362DRV board that does the printer end of book.
Page 85: Power Supply Circuit Board Description
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.5 Power supply circuit board description There are 3 control signals among the C362MAIN board and power supply board. The details are shown in the following table. Table 2-8. Action explanation 100V AC from the plug socket is supplied to the inlet and power supply board of this printer through the power cable of this printer belonging.
Page 86: Chapter 3 Troubleshooting
Thank You For Using TheServiceManualShop.com C H A P T E R TROUBLESHOOTING Thank You For Using TheServiceManualShop.com...
Page 87: Outline
The printer is not abnormally dirty. Clean if necessary. The trouble-shooting based on the 3.4 printing result(the object: service man) The printer parts are original or EPSON replacement parts and no part of the Thereafter, I explain the confirmation point and also confirmation contents on trouble- printer is deformed or out of shape in any way.
Page 88: Troubleshooting Using The Error Messages
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 3.2 Troubleshooting Using the Error Messages Table 3-1. Status Reply Priority Prioyity Status This machine does the self diagnosis on the basis of the detection condition in each During ink sequence...
Page 89: Leds
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 3.2.2 LEDs Table 3-2. Indicator Display Indicator Status Condition Table 3-2. Indicator Display Out of specified ink Indicator Status Condition No cartridge for specified ink Wrong cartridge for specified ink...
Page 90: Warning
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 3.2.3 Warning "Warnings" take the place of LCD "READY" and "PRINTING" messages in order to notify the user of the condition. They do not have an influence on printer operation, and printing can be continued.
Page 91: Error
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 3.2.4 Error Table 3-4. Panel display LCD message Status Reference This table explains the error messages and LED indicator conditions that can be corrected by the user and provides error details and cancellation methods.
Page 92 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 3-6. Different paper source is selected on panel Table 3-8. Paper jam Item Description Item Description LCD message LOAD xxxx PAPER LCD message PAPER JAM • "PAPER OUT" LED goes on.
Page 93 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 3-10. Paper cutting error Table 3-11. Paper not straight Item Description Item Description LCD message PAPER NOT CUT LCD message PAPER NOT STRAIGHT LED indicator LED indicator "PAPER OUT" LED blinks.
Page 94 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 3-12. Paper check error / Paper eject error (sheet) Table 3-13. Auto take-up reel failed Item Description Item Description LCD message RELOAD PAPER LCD message RELOAD PAPER LED indicator status "PAPER OUT"...
Page 95 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 3-15. Ink end Table 3-18. Can not test print Item Description Item Description LCD message INK OUT LCD message UNABLE TO PRINT LED indicator status Corresponded "INK OUT" LED goes on.
Page 96 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 3-20. Ink cover open Table 3-23. Defective ink Cartridge Item Description Item Description LCD message CLOSE INK CART. COVER LCD message DEFECTIVE INK CRTG LED indicator LED indicator status Corresponded color LED goes on.
Page 97: Service Engineer Require Message
Replace the pump cap unit. (Refer to 4.3.3.13 "Removing the Pump Cap Unit") NOTE: The above parts are supplied with the parts package "Maintenance Kit (Waste Ink Pads/Pump Cap Unit), Stylus Pro 10000/10000CF." Thank You For Using TheServiceManualShop.com Troubleshooting Service engineer require message...
Page 98 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com MAINTENANCE REQ. 0101 MAINTENANCE REQ. 0102 Problem Problem The CR motor reached the 3% remaining to the life. Auto nozzle check error Explanation Explanation This message appears when counted CR motor movement cycles (pass number) This message appears when laser light cannot be received or cannot be recognized reach 4% (about 4.8 million passes) of the set value (4.8 million passes).
Page 99 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com MAINTENANCE REQ. 0104 Problem Dot missing detector error Explanation This message appears and printer is stopped when power is turned on and required value output (light quantity) from the dot missing detector is not measured.
Page 100: Fatal Error
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 3.3.2 Fatal error Table 3-26. Fatal Error Code List Code Description This section describes Service Call Errors that appear in the control panel LCD to notify the user that checking/corresponding part replacement by a service engineer is...
Page 101 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 3-26. Fatal Error Code List Table 3-26. Fatal Error Code List Code Description Code Description 00020000 NVRAM error 10000180 CPU reservation instruction code exception error 00020001 NVRAM check sum error...
Page 102 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00000100: Waste ink tank full SERVICE REQ. 00010000: PF encoder check error Problem Problem Waste ink tank overflow PF motor encoder check error Explanation Explanation Shows that waste ink pads has become full of waste ink and remaining capacity is This message appears and printer is stopped when the encoder pulse signal is not 0%.
Page 103 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00010001: PF motor step-out SERVICE REQ. 00010002: PF motor over current Problem Problem PF motor step-out PF motor overcurrent Explanation Explanation This message appears and printer is stopped when the PF motor is determined to...
Page 104 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00010003: PF motor in position time out SERVICE REQ. 00010004: CR encoder checking error Problem Problem PF motor in position time out CR motor encoder check error...
Page 105 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00010005: CR motor step-out SERVICE REQ. 00010006: CR MOTOR OVER CURRENT Problem Problem CR motor step-out CR motor overcurrent Explanation Explanation This message appears and printer is stopped when the CR motor is determined to...
Page 106 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00010007: CR motor in position time out SERVICE REQ. 00010008: Servo interruption watch dog time out error Problem Problem CR motor in position time out Servo interruption watch dog time out error (DC motor drive interruption)
Page 107 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 0001000A: CR origin (home position) sensor mulfanction SERVICE REQ. 0001000C: HS origin (head slide home position) sensors malfunction Problem Problem CR origin detection error (home position detection error for CR)
Page 108 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 0001000D: Cover sensor mulfanction SERVICE REQ. 0001000F: CR motor over heat (PWM output SERVICE REQ. 0001000E: Cover sensor mulfanction Malfunction) Problem Problem Front cover sensor malfunctioning CR motor PWM current output malfunction...
Page 109 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00010010: PF motor over heat (PWM output SERVICE REQ. 00010013: Providing system origin error malfunction) Problem Problem Ink supply system origin error PF motor PWM current output malfunction...
Page 110 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00010015: liquid sensor overflow (K) SERVICE REQ. 0001001B: head driver (TG) temperature error SERVICE REQ. 00010016: liquid sensor overflow (C) Problem SERVICE REQ. 00010017: liquid sensor overflow (M) SERVICE REQ.
Page 111 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 0001001D: CR servo parameter error SERVICE REQ. 0001001E: PF servo parameter error Problem Problem CR servo parameter error PF servo parameter error Explanation Explanation This message appears and printer is stopped when voltage above required value is This message appears and printer is stopped when voltage above required value is about to be output to CR motor.
Page 112 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00010020: CSIC read/write error SERVICE REQ. 00010022: Ink NVRAM status error (C362DRV setting) Problem Problem CSIC read/write error Setting is outside dyes/pigments. Even though "CSIC detection: OFF" is set, condition has become "Ink Type: Explanation Neutral."...
Page 113 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 0010024: Module communication time-out error SERVICE REQ. 0010026: RTC access error Problem Problem Communication between modules time out error RTC access error Explanation Explanation This message appears and printer is stopped when a communications error is...
Page 114 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 0010028: During cleaning, pressure pump small leak SERVICE REQ. 00020001: NVRAM check sum error error Problem Problem NVRAM check sum error During cleaning, pressure pump small leak error...
Page 115 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00020003: BOOT program check SUM error SERVICE REQ. 0002000B: Internal memory storage error Problem Problem BOOT program check sum error Internal memory storage error Explanation Explanation This message appears and printer is stopped when part of F/W boot program has This error is generated when cache area is insufficient.
Page 116 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 00030015: Ink supply defective (K) SERVICE REQ. 0003001B: Gap adjustment range Error SERVICE REQ. 00030016: Ink supply defective (C) Problem SERVICE REQ. 00030017: Ink supply defective (M) SERVICE REQ.
Page 117 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 1000**** Problem CPU internal irregularity trap error Explanation CPU device failure or CPU internal bug. Solution This is not usually generated after sale, but if by chance this message does appear follow the corrective actions below.
Page 118: Troubleshooting Based On Printout
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 3.4 Troubleshooting Based On Printout When replacing the C362DRV Board or printhead, check the C A U T I O N connection condition of the connection cable (FFC). Be specially...
Page 119: Smudged Or Marred Printout (Front)
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 3.4.3 Smudged or Marred Printout (Front) 3.4.5 White or Black Banding Check the following items if smudges are generated by rubbing of head against print If white or black banding (lines across the page) appear on your printout, try the surface of paper.
Page 120: Chapter 4 Disassembly & Assembly
Thank You For Using TheServiceManualShop.com C H A P T E R DISASSEMBLY & ASSEMBLY Thank You For Using TheServiceManualShop.com...
Page 121: Summary
4.1 Summary 4.1.1 Warnings Before proceeding with any Disassembly or assembly work, make absolutely sure of This section describes the Disassembly and assembly methods for the EPSON Stylus the following. Pro 10000/10000CF/10600. However, full assembly instructions are not given apart from following the Disassembly instructions in reverse order, and where special instructions are necessary, reassembly points are provided.
Page 122 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Do not remove and loosen the screw of the part that showed it C A U T I O N C A U T I O N below. There is the danger that is impossible adjustment in the field and cause a new obstacle and also become a reconditioning impossibility.
Page 123 132Kg with stand), you need to take extra care. If you need to (Stylus Pro 10000/10000CF: P/N1060626, Stylus Pro 10600: P/ take apart the printer and stand or lift the printer, four persons N1214261), and then perform an initial ink charge with the fluid.
Page 124: Tools
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.1.2 Tools Table 4-2. Screws (continued) Type Color Description The tools needed for the Disassembly/assembly of this machine be the Chapter 5- 5.1.2 clause reference. CBS M3x6 white (+) Bind S-tight...
Page 125: Disassembly Flow
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.2 Disassembly Flow Refer to the following flowchart when determining the Disassembly flow. 4.2.2 Remove Circuit Board 4.2.1 Remove Housing 4.2.3 Disassemble Printer Mechanism Waste Ink Unit Suction Control Motor...
Page 126: Disassembly
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3 Disassembly 4.3.1 Removing the Housing This sections describes the removal procedure for printer housing parts. See below for an illustration of the housing parts. Roll Top Cover H Top Cover...
Page 127: Panel Unit Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.1.1 Panel Unit Removal You may find it easy to remove the panel unit if you stand on the C H E C K Push the clips (Refer to Figure 4-5.) on both sides of the panel unit and pull...
Page 128: Paper Set Lever Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.1.2 Paper Set Lever Removal Remove a E ring securing the Paper Set Lever to the axis. Lift up the Paper Set Lever to the released position. Remove two screws (CBP: M4 x 10) and remove the Pressure Lever Knob.
Page 129: H Top Cover Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.1.3 H Top Cover Removal Remove the H Top Cover by pulling up and toward the front. Open Front Cover and Roll Paper Cover. Remove top side four screws (CS: M4x8), then remove front side two screws (CS:...
Page 130: R Side Cover Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.1.4 R Side Cover Removal Remove two screws (CPP: M4x12). Remove the Panel Unit and H Top Cover. (Refer to 4.3.1.1 "Panel Unit Removal". and 4.3.1.3 "H Top Cover Removal".) Remove rear side two white screws (CS: M4x8).
Page 131: L Side Cover Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.1.5 L Side Cover Removal From the inside, remove two black screws (CS: M4x8). Remove the H Top Cover as described in 4.3.1.3 "H Top Cover Removal". Remove rear side two white screws (CS: M4x8).
Page 132: I/H Cover Assy Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.1.6 I/H Cover ASSY Removal Opening I/H Cover by pushing the central upper part (the cover latch location) of it, then remove I/H Cover with the hinge of the right and left.
Page 133: Rear Cover Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.1.7 Rear Cover Removal Remove two white screws (CBS: M4x6) securing the parallel interface, one white screw (CBS: M3x6) securing the USB interface, one screw securing the serial From the rear, remove four white screws (CPS: M3x12) securing the optional interface, four screws securing the option cover 1, 2, and four screws securing the interface cover, and remove the optional interface cover.
Page 134 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove one white screw securing the AC inlet. Remove six white screws (CBS: M4x8) securing the cover lower part, then remove eight white screws (CBS: M4x8) securing the cover upper part.
Page 135: Paper Guide L Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.1.8 Paper Guide L Removal From the bottom, remove six white screws (Truss: M4x6). To avoid injury and Paper Guide L damage, make sure the C A U T I O N protection of drop with proper method.
Page 136 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove front four white screws, then remove the Paper Guide L. When installing Paper Guide L, insert all 5 tabs at top edge into Tape C A U T I O N Sub-Platen slots and secure screws so that tabs do not protrude above surface.
Page 137: Roll Paper Cover Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.1.9 Roll Paper Cover Removal 4.3.1.10 Front Cover Removal Open the Roll Paper Cover. Remove the R Side Cover. (Refer to 4.3.1.4 "R Side Cover Removal".) Remove the upper and lower roll paper with roll shaft.
Page 138: Removing Paper Guide U
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove the Hinge Unit L with Hinge. 4.3.1.11 Removing Paper Guide U While supporting the Front Cover, lower the left side and slide to left, then remove Remove the H Top Cover as described in 4.3.1.3 "H Top Cover Removal".
Page 139 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove the FFC from rear side. Remove the Paper Guide U by pulling upward. Remove five screws (CS: M4x8) securing the Paper Guide U from rear side. When removing / installing the Paper Guide U, do not touch the C A U T I O N P_Rear Sensor.
Page 140: Circuit Board Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.2 Circuit Board Removal Disconnect the P/S Self-containing Fan connector connected to CN39 on the C362DRV board. This section explains how to remove the Power Board, the HJFK / Dummy Board, the Disconnect cable connector C362MAIN Board, the CSIC Board, the C362DRV Board and the P/S Fan.
Page 141: Hjfk / Dummy Board Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.2.2 HJFK / Dummy Board Removal Remove four screws (M3), then the board and the bracket are separated. (Any of the HJFK board or the Dummy board of the option are fixed.) Screws Remove the Optional Interface Cover of rear as described in 4.3.1.7 "Rear Cover...
Page 142: C362Main Board Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.2.3 C362MAIN Board Removal Slide the C362MAIN Board 20 to 30mm to the left, then remove the C362MAIN Board. Remove the Rear Cover as described in 4.3.1.7 "Rear Cover Removal".
Page 143: Board Assy Csic Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.2.4 Board ASSY CSIC Removal Remove the R Side Cover as described in 4.3.1.4 "R Side Cover Removal". Remove the cables from the following connectors. (Eleven cables) Table 4-4. CSIC Board Connectors...
Page 144: C362Drv Board Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.2.5 C362DRV Board Removal Table 4-5. C362DRV Board Connectors Connector # Pins Color Connection Remove the Rear Cover and HJFK as described in 4.3.1.7 "Rear Cover Removal". CN31 2 (Red / Black) P/S Self-containing Fan Remove the C362MAIN Board.
Page 145 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com For connector locations, refer the illustration below. Serial I/F CN39 CN41 CN42 CN49 CN43 CN51 CN47 CN12 CN17 CN44 CN48 CN25 CN11 CN14 CN29 CN53 CN45 CN55 CN52 CN18...
Page 146 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Be sure NOT to remove the C362DRV Board without removing Clamp location C A U T I O N the C362MAIN Board in advance. Otherwise, the chip (C362MAIN Board area)
Page 147: P/S Fan Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.2.6 P/S Fan Removal Remove one screw securing the P/S Fan Holder, then remove it. One screw securing the P/S Fan Holder Remove the Rear Cover as described in 4.3.1.7 "Rear Cover Removal".
Page 148 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com When replacing the fan, make sure the setting direction. Label Figure 4-59. Thank You For Using TheServiceManualShop.com Disassembly & Assembly Disassembly...
Page 149: Printer Mechanism Disassembly
This section describes the procedures for disassembling the printer mechanism from the printhead surface and nozzles into the Waste Ink Pads. Once a predetermined components of EPSON Stylus Pro 10000/10000CF/10600. amount of waste ink has been drained, the printer displays the “Maintenance Request 0100”...
Page 150 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove the Handle of one place by pressing latches. At the bottom side, pull (unlock) the two tabs of Ink Box and slide the Ink Box toward you. (Rear side)
Page 151 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com While lifting the hooks on each side of the Waste Ink Box, pull it forward slowly, Remove the old waste ink absorption material, place it in a plastic bag and dispose and then remove the box after releasing the tabs hooked on the base frame.
Page 152: Removing The Suction Fans
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.2 Removing the Suction Fans Remove the H Top Cover. Remove the Right and Left Side Cover. Guide rail Remove the Rear Cover. Move the Head Carriage to the home position.
Page 153 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove each two screws securing the Roller Unit (5 pieces), and remove the Roller Unit from the Guide Unit. Carry out the justify with the L style gauge, when assemble the sub...
Page 154 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 12. Remove twelve screws (M4x8) securing the Fan Duct and open the Fan Duct. 13. Open slowly the Fan Duct as shown below. * Do not mind six screw of the upper sides are dropped inside the Fan Duct without taking out.
Page 155 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 14. Open as inside of the fan duct becomes upward like the rough sketch, after it raises 15. Disconnect left side suction location detect sensor cable connector. it a little upward, while paying attention so as not to scar each cable of the right Suction location and left.
Page 156 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 18. Remove four screws (M4x8) securing each Suction Fan cover. 20. Remove three screws (CP(W) M4x8), then remove the Suction Fan. Screws Sction Fan Flame Sction Fan Screws Screws Figure 4-76.
Page 157: Replacing The Printhead
The cleaning liquid used for Stylus Pro 10600 has been changed Lock lever to CR02. S46 which is used for Stylus Pro 10000/10000CF cannot be used. Refer to below table. SP 10000/10000CF SP 10600...
Page 158 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove two screws (CP(W): M3x6) securing the carriage cover and remove the carriage cover. Do not lose the O ring (rubber sealing ring) between the tube and C A U T I O N nut.
Page 159 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Disconnect all head cables (6 pieces) from the Head Board. Remove one screw securing the Earth Plate. Do not drop the nut of the reverse side. Head cable Screw Figure 4-85.
Page 160 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 10. Remove the screw of the upper side while holding down the Compression Spring 11. Remove two screws securing the Printhead to the Head guide of the right and left.
Page 161 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 12. Remove each two screws fixing the Head guide of the right and left. 15. Raising a few of the lower part of Printhead, then draws out it to the front lower side.
Page 162: Removing Head Weight Set
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.4 Removing Head Weight Set <Stylus Pro 10600> Insert a 30cm screwdriver through opening created by removal of R Inside Cover. Remove 1 screw (W Sems M3x8) securing the weight to the Carriage.

Page 163 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Move the carriage to the left end. (Refer to Figure 4-95.) Remove Weight and Weight Retainers (x2). Weight Weight Retainers Figure 4-97. Weight and Weight Retainers Figure 4-95. Head Weight Set Removal Position Remove 3 screws securing the weight to the carriage.
Page 164: Reassembling Head Weight Set
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.5 Reassembling Head Weight Set <Stylus Pro 10600> Slide the CR Weight Retainer (Left) down until it touches the CR Base, then slide it to the left until it touches CR Frame L.

Page 165 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Temporarily set the Weight in place against the Retainers with 4 screws. (Do not Insert 1.60mm thickness gauges between the left and right sides of the Weight and tighten.) the Head and leave them in place.
Page 166 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Check the following points. Tighten 3 screws that were temporarily set. (Torque: 10kgf) (Screws to tighten are those shown in Figure 4-96.) 10. Remove thickness gauges. 11. Move the Head Tilt Adjuster fully to the left and right, checking that Head and Weight have no interference.
Page 167: Removing The Cutter And Cutter Unit
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.6 Removing the Cutter and Cutter unit Push down and hold the Cutter Lever then pull up the solenoid and rotate it to the arrow direction. Remove the R Side Cover.
Page 168 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Disconnect the connector cable from Head Board, and remove two screws securing Cutter Unit, then romove the Cutter Unit. When installing cutter unit, use the L-shaped gauge to adjust the A D J U S T M E N T position in relation to the sub-platen.
Page 169: Removing The Cr Encoder Sensor
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.7 Removing the CR Encoder Sensor 4.3.3.8 Removing the P_Edge Sensor Remove the R Side Cover. Remove the R Side Cover. Remove the H Top Cover. Remove the H Top Cover.
Page 170: Removing The Ink Cartridge Holder & Slots
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.9 Removing the Ink Cartridge Holder & Slots Disconnect the six air tubes. CSIC board The Ink Cartridge Holder is made up of six individual slots, one for each color of ink.
Page 171: Cr Motor/Pulley Assy Steel Belt Removal
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove 12 hex head nuts connecting ink pipes, then remove ink pipes. 4.3.3.10 CR Motor/Pulley ASSY Steel Belt Removal Remove two screws (M3x8) securing Ink Cartridge Holder. Remove R Side Cover as described in 4.3.1.4 "R Side Cover Removal".
Page 172 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Use a hex-head wrench (2mm) to remove 1 stopping screw at the Head right side Remove 4 screws securing the CR Motor/Pulley ASSY, pull out the CR Steel Belt, (as seen from printer front).
Page 173: Removing The Pf Motor Assy
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.11 Removing the PF Motor ASSY Loosen 4 screws (CP (W) M4x10) securing PF Motor bracket, then slide bracket in direction of arrow shown in Figure 4-120 to loosen PF Motor timing belt Remove the L Side Cover as described in 4.3.1.5 "L Side Cover Removal".
Page 174: Removing The Pf Encoder
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.12 Removing the PF Encoder When removing PF Motor, be careful not to allow motor pinion Disconnect the PF Encoder cable connector. C A U T I O N (metal gear) to be damaged by contacting frame.
Page 175 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove four serews securing the PF Base. While holding down the PF Encoder from inside, remove two screws and remove the PF Encoder. PF base Screws Screws Figure 4-125.
Page 176: Removing The Pump Cap Unit
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.13 Removing the Pump Cap Unit Disconnect cable connecting CSIC Board to Pump Cap Unit. (CSIC Board CN10) CSIC board When Cleaning Unit has been replaced due to error generation...
Page 177 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com While supporting the Pump Cap Unit from the rear by hand, remove 2 screws (M4x8) securing the Pump Cap Unit to the CR Guide Rail. CR Guide rail Cleaning Unit...
Page 178: Removing Flushing Box
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.14 Removing Flushing Box Release waste ink tubes from tube clamps (3 places). While pulling waste ink tubes out through hole in printer right frame, remove the Remove the R Side Cover as described in 4.3.1.4 "R Side Cover Removal".
Page 179: Removing Dot Missing Detector
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.15 Removing Dot Missing Detector Remove the Flushing Box as described in 4.3.3.14 "Removing Flushing Box". Use a finger to grasp the rear side of the Ink Pump Assy and lift it in the direction of the arrow.
Page 180 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Disconnect the cable for the Panel Unit from the cable clump on the Dot Missing Detector. Use a magnetic tip screwdriver when removing/installing screws C A U T I O N and be careful of the following points.
Page 181: Removing The Shutter Motor
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.16 Removing the Shutter Motor 4.3.3.17 Removing the Ink Pump ASSY Remove the Flushing Box as described in 4.3.3.14 "Removing Flushing Box". Remove the Pump Cap Unit as described in 4.3.3.13 "Removing the Pump Cap Unit".
Page 182: Removing The Scale, Cr
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove five screws (M4x8) securing Ink Pump ASSY, then remove it. 4.3.3.18 Removing the Scale, CR Remove the R Side Cover as described in 4.3.1.4 "R Side Cover Removal".
Page 183: Removing The Paper Hold Solenoid
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove a right side edge screw (M3x6), then remove the Scale, CR. 4.3.3.19 Removing the Paper Hold Solenoid Remove the R Side Cover as described in 4.3.1.4 "R Side Cover Removal".
Page 184 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove right side two screws (M4x6) and front upper side two screws (M4x6), then remove the Paper Hold Solenoid with bracket. When installing the Paper Hold Solenoid, make sure the lock lever...
Page 185: Removing The Head_Slide Sensor Assy
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.20 Removing the HEAD_SLIDE Sensor ASSY 4.3.3.21 Removing the HEAD_SLIDE Motor / Drive Gear Remove the R Side Cover as described in 4.3.1.4 "R Side Cover Removal". Remove the R Side Cover as described in 4.3.1.4 "R Side Cover Removal".
Page 186: Removing The Cr_Hp Sensor
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove two screws securing the HEAD_SLIDE Motor, then remove the PG 4.3.3.22 Removing the CR_HP Sensor motor. Remove the R Side Cover as described in 4.3.1.4 "R Side Cover Removal".
Page 187: Removing The Paper Release (Pressure Lever) Sensor
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.23 Removing the Paper Release (Pressure Lever) Sensor 4.3.3.24 Removing the P_FRONT Sensor ASSY Remove the R Side Cover as described in 4.3.1.4 "R Side Cover Removal". Remove the R Side Cover as described in 4.3.1.4 "R Side Cover Removal".
Page 188 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove the Paper Guide L as described in 4.3.1.8 "Paper Guide L Removal". Close front cover. Release P_FRONT Sensor harness from cable clamp, then remove P_FRONT Sensor from printer.
Page 189: Removing The P_Rear Sensor Assy
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.25 Removing the P_REAR Sensor ASSY 4.3.3.26 Removing the Front Cover Sensor ASSY Remove the Paper Guide U as described in 4.3.1.11 "Removing Paper Guide U". Remove the Front Cover as described in 4.3.1.10 "Front Cover Removal".
Page 190: Removing The I/C Holder Cover Sensor Assy
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Remove two screws (Mx8) securing Front Cover Sensor R. 4.3.3.27 Removing the I/C Holder Cover Sensor ASSY Screws Remove the R side Cover as described in 4.3.1.4 "R Side Cover Removal".
Page 191: Removing The P_Thick Sensor
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 4.3.3.28 Removing the P_THICK Sensor Remove two screws (M3x6) securing the P_THICK Sensor. Screws P_THICK sensor Remove the H Top Cover as described in 4.3.1.3 "H Top Cover Removal".
Page 192 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Unlock rear side three latches, then separate the P_THICK Sensor to the bracket. Bracket Latch Figure 4-172. NOTE: Sensor bracket position is adjusted at factory. Therefore, be sure to mark its current position before removing the screw.
Page 193: Chapter 5 Adjustment
Thank You For Using TheServiceManualShop.com C H A P T E R ADJUSTMENT Thank You For Using TheServiceManualShop.com...
Page 194: Adjustment Outline
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.1 Adjustment Outline Table 5-1. Repair Items and Required Adjustment Items Adjustment Repair Item Adjustment Items Reference This chapter describes adjustment items and special operations methods that are Procedure needed during repair.
Page 195 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 5-1. Repair Items and Required Adjustment Items NOTE: (*1) When it is possible to back up parameters from the C362DRV Board before replacement, the parameters can be downloaded to the new...
Page 196: Tools For Adjustment/Special Operations
This section describes about tools that is required by adjustment/special operations for required adjustment. Scale insertion tool 1070174 CR_loop scale fixing Starter Cartridge Lc 1062231 Stylus Pro 10000 (except EAI market) Table 5-2. Adjustment Tools Starter Cartridge Lc 1062243 Stylus Pro 10000CF (Except EAI market) Name Part Code...
Page 197: Adjustment/Special Operations Methods
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.2 Adjustment/Special Operations Methods 5.2.1 Head Rank Input In order to ensure optimum print quality, this printer evaluates the characteristics of This section explains about special operations and its execution steps as shown in the each printhead, specifies a printhead ID for each printhead and registers these in content of Table 5-1.
Page 198 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com REQUIREMENTS FOR PARAMETER BACKUP STEPS FOR BACKING UP PARAMETERS FROM C362DRV BOARD #F727 Flash Memory Card (1050073) Remove the slot cover (secured by 2 screws) located on Rear Cover.
Page 199 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com STEPS FOR DOWNLOADING PARAMETERS TO C362DRV BOARD BACKUP/DOWNLOAD ERROR RECOVERY Remove the slot cover (secured by 2 screws) located on Rear Cover. The following message will be displayed if an error is generated during writing of data to the memory card or C362DRV Board flash memory.
Page 200: Firmware Download
Use the backup card with which firmware is written in only for "Updating C2 F/W..." will be displayed and the Power LED and "LC" LED "Stylus Pro 10000/10000CF/10600". Do not use the backup card will light. other than this product.
Page 201: Write Usb-Id
Board. When the C362DRV Board is replaced, perform writing of the USB-ID. specific parts. The following table is shown about the parts for which adjustment is This writing operation must be done with "EPSON Printer Adjustment Program required and the adjustment items.
Page 202: Cr Steal Belt Tension Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.3.1 CR steal belt tension adjustment 5.3.2 PF timing belt tension adjustment This adjustment is applied to all the operation accompanied by CR Motor/CR Steel This adjustment is applied to all the operation accompanied by PF Motor/PF Timing Belt removal and installation.
Page 203: P_Thick Sensor Fixing Bracket Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.3.3 P_THICK sensor fixing bracket adjustment 5.3.4 Cutter position adjustment The following adjustment with the self-diagnostic function is performed for completed The following adjustment is performed for completed operations related to operations related to replacement of P_Thick Sensor or removal the sensor installation replacement or installation of Sub-Platen/Cutter Holder/Cutter Solenoid.
Page 204: Front Cover Sensor Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.3.5 Front cover sensor adjustment Turn on the printer power and implement and confirm the paper cut operation. The following adjustment with the self-diagnostic function is performed for completed L Type adjusting tool operations related to replacement or removal of Front Cover/Front Cover sensors.
Page 205: T Fence And Cr Encoder Position Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.3.6 T fence and CR encoder position adjustment 5.3.7 Head slant adjustment Adjustment procedure (Use the CR_ENC setting tool.) Refer to "A13 slant adjustment" on page 232 to "B123 slant adjustment" on page 234 for adjustment standard and adjustment procedure.
Page 206: Offset Adjustment For Dot Missing Detector
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.3.8 Offset adjustment for dot missing detector Table 5-5. FRONT/REAR/P_Edge Sensor adjustment Automatically offset values are fixed after the dot missing detection operation. Refer to Sensor Adjustment sheet Left (ON-OFF) Fine adjustment the paragraph "Offset adjustment for dot missing detector"...
Page 207: Paper Feeding Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.3.9 Paper feeding adjustment Hook the tension gauge on the cutter solenoid. Refer to TJ01-304Rev.A of T/I (Technical Information) number. Tension Gauge 5.3.10 Cutter Pressure Adjustment This adjustment is applicable from firmware version (TBD). This adjustment is...
Page 208: Self-Diagnostics
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4 Self-Diagnostics Table 5-7. Self-Diagnostic Menu Stratum Self diagnostics purposes mechanism adjustment and determining firmware adjustment Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 parameter. The function is built in the firmware. This function can be carried out by turning the printer on while pressing specific button.
Page 209 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 5-7. Self-Diagnostic Menu Stratum Table 5-7. Self-Diagnostic Menu Stratum Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 Front AD Ink cover Rear AD CR motor Ink level PF motor Head temperature.
Page 210 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 5-7. Self-Diagnostic Menu Stratum Table 5-7. Self-Diagnostic Menu Stratum Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 Measure Measure LC D/A K D/A correction correction Check...
Page 211 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 5-7. Self-Diagnostic Menu Stratum Table 5-7. Self-Diagnostic Menu Stratum Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 K cartridge CSIC information - Cap motor C cartridge...
Page 212 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 5-7. Self-Diagnostic Menu Stratum Table 5-7. Self-Diagnostic Menu Stratum Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 Bid 240, V1, K Bid2 240, V1, K Bid 240, V1, C...
Page 213 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 5-7. Self-Diagnostic Menu Stratum Table 5-7. Self-Diagnostic Menu Stratum Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 Hierarchy1 Hierarchy2 Hierarchy3 Hierarchy4 Hierarchy5 Normal KK0 Cap position Normal KK1 Head rank *1...
Page 214: Start-Up Procedure
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.1 Start-up procedure 5.4.2.1 Top menu Top menu sequence is shown below. Following Button operation that triggers self-diagnostic function. Power off condition Item Enter Press and hold the "Paper Feed +", "Paper Feed -" and "Cut/Eject" button.
Page 215: Test
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.3 Test 5.4.3.1 Test menu sequence Test menu sequence is shown in the Figure 5-13. This function purposes checking the circuit board. Test items are shown in the Table 5-9.
Page 216: Version Display
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.3.2 Version display ※ Additional information for version display. Display the firmware version. (I/F controller, Engine controller) Display the version as follows; ddym Ensure the ESC/P3 controller, Backup parameter and Dip SW (on:0,off:1).
Page 217: Panel
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.3.3 Panel 5.4.3.4 Sensor Test the key, LCD and LED on the panel. Display the sensor condition. Figure 5-16 showing sensor test menu sequence. When entering the sensor menu, place the carriage to the home position and perform the Figure 5-15 showing panel test sequence.
Page 218: Encoder
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com "INK NOT xxxxxx" : Display of "xxxxxx" means ink cartridge name with 5.4.3.5 Encoder symbolic code. Display the CR and PF encoder value. "EdgeAD xxxyyy"/"FrontAD xxxyyy/"RearAD xxxyyy" : Figure 5-18 showing the encoder test sequence.
Page 219: Fan
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.3.6 Fan 5.4.3.7 Encode Test the each fan operation. Display the maintenance and fatal errors. Figure 5-19 showing Fan test sequence. Figure 5-20 showing record menu. Item Item Enter...
Page 220 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Maintenance record Figure 5-21 showing maintenance record menu. Fire LC : 00000000Mdot Waste INK R : 00000000 Waste ink R Fire LM : 00000000Mdot Waste INK L: 00000000 Fire Y : 00000000Mdot...
Page 221: D/A Correction
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Error record 5.4.3.8 D/A correction Display the error record. Correct the head drive bias. CPU error is not include for critical error. Correction value and drive bias check is available.
Page 222 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Voltage measurement /Check Parameter selection from measurement result. Select the measurement or check the voltage. Select the voltage parameter of Va - Vd. Figure 5-24 showing menu sequence. Figure 5-25 showing menu sequence.
Page 223 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Correction data input screen. Screen for the "Va" to" Vd" input. Selection of the parameter Figure 5-26 showing screen menu sequence. Select the voltage parameter for "Va" to" Vd".
Page 224: Head Signal Shape
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.3.9 Head signal shape CSIC information Output the miscellaneous signals. Display the CSIC internal information. The function is used for the factory evaluation. Figure 5-30 showing CSIC menu sequence.
Page 225: Actuator
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.3.11 Actuator Move the various solenoid. Item K13 : xx Pay for the attention to the "Ink valve Solenoid" test. SelecType Item Pump air is not compressed: The ink will flow to the cartridge directions.
Page 226: Actuator 2
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.3.12 Actuator 2 This item moves various actuator move. Pay for the attention to the "Ink valve Solenoid" test. Item Enter Pump air is not compressed: The ink will flow to the cartridge directions.
Page 227: Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4 Adjustment Shutter Change the shutter position with panel operation. Perform the mechanical adjustment (Head slant) and firmware parameter adjustment. Figure 5-33 showing shutter menu. All of adjustment items are adjusted at the factory. Head cleaning with wash I/C...
Page 228: Adjustment Menu
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.1 Adjustment menu 5.4.4.2 Paper Skew Following figure showing adjustment menu sequence. Feed the paper and check the paper edge position with the P_Edge sensor, then compare the difference between start position and stopped position. The result is...
Page 229: Head Rank Input
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.3 Head Rank input QR code input Head rank is the characteristic of the head and each head has own value (QR code). Mode for the QR code input.
Page 230 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Panel input 2-1. All Mode for the input type selection. Mode for the head number selection in order to input the code of dyestuff and pigment ink. Figure 5-39 showing selection menu sequence.
Page 231 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2-2. Input line selection 2-3. Code input for each lines. Mode for the input line selection. Figure 5-41 showing line number selection menu. Mode for the input at all lines. Cursor is appeared under the input column.
Page 232 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Move the cursor to the right with "SelecType" key. 2-4. Dyestuff Move the cursor to the left with "Item" key. Mode for the head selection of dyestuff ink code.
Page 233 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2-5. Code input for the dyestuff Move the cursor to the right with "SelecType" key. Move the cursor to the left with "Item" key. Mode for the head code input. Cursor is appeared under the input column.
Page 234 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2-6. Pigment ink 2-7. Cord input for pigment Mode for the head selection of pigment ink code Mode for the head code input. Cursor is appeared under the input column.
Page 235: Head Nozzle Check
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Cursor skip the space area. 5.4.4.4 Head nozzle check When the [Enter] key is pushed with [Head * -1]-[Head * -4], display moves to the Ensure the dot nozzle operation with test print sample.
Page 236 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com <Print sample for nozzle check pattern> 1. Check items: Nozzle ink injection (missing / uncontinuation / wind line) Satellite Press the [Enter] key to select Timing fence the [A13 slant adjustment].
Page 237: Offset Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5. Horizontal nozzle lineup confirmation 5.4.4.5 Offset Adjustment It prints it in the order of Black/Cyan/Magenta/Yellow/Light Magenta/Light Cyan Perform the dot missing detection and adjust the offset value automatically.
Page 238: Test Report For Dot Missing Detector
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.6 Test report for dot missing detector 2: Count Value Of dot lost nozzle. Print out the test result at the end of dot missing detection test. Color (K) Figure 5-53 showing the test report for dot missing detector.
Page 239: A13 Slant Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.7 A13 slant adjustment <Print sample> Check items: Black lines and Magenta lines are continue as same level by a Print the test pattern and make sure the print quality by referencing the Figure 5-56.
Page 240: A123 Slant Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.8 A123 slant adjustment <Print sample> Check items: Black lines, Light Cyan lines and Magenta lines are continue as same Print the test pattern and make sure the print quality by referencing the Figure 5-58.
Page 241: B123 Slant Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.9 B123 slant adjustment <Print sample> Check items: Cyan lines, Light Magenta lines and Yellow lines are continue as Print the test pattern and make sure the print quality by referencing the Figure 5-60. If same level by a magnifying glass with scale.
Page 242: Bi-D Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.10 Bi-D adjustment Printing position adjustment with Bi-D printing. Adjust the print position for each [Enter] Adjust Print color of head 1 to 3. Print the test pattern and make sure the print quality of CW print position and CCW print position then input the value of difference.
Page 243 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com When press the "Enter" key during the "BiD End" display, operation mode shift to the "Adj:Head_LR". Print all of the test pattern when "Enter" key is pressed during the "[Enter] Adjust Print"...
Page 244: Head Lr (Head Gap) Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.11 Head LR (Head gap) adjustment Correct the head to head gap. Print the test pattern with Uni-D mode and make sure the print quality by referencing the Figure 5-64 then input the correction value.
Page 245 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Difference of maximum and minimum correction value are within 64/1440 inch with six colors. <Print pattern> Adjustable with "Paper Feed +/ Gap 300, V2, M -" key at unit of 1/2880 inch.
Page 246: Feed Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.12 Feed adjustment <Print pattern> Perform the distance revision in the paper conveyance. Print the line pattern in Adjustment item: Paper feed length direction of paper feeding and input the distance in order to decide the PF encoder Printing method: Length 1000mm/ Two pass with Uni-D at 720dpi resolution for CR resolution by firmware.
Page 247: Top And Bottom Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.13 Top and Bottom adjustment Front: Correction pattern for cutter-head length. Perform the printing and form cut then input the distance of front sensor-head, cutter- Adjustment item: Top margin (Front sensor position) /Bottom margin (Cutter position)
Page 248: Rear Sensor Position
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.14 Rear sensor position Shift to the "Test print" by pressing "Enter" key during the "Rear sensor" display. This adjustment to detect the form length of cut paper precisely. The position of rear sensor inside firmware is adjusted on the basis of the nozzle to secure the maximum Pause range from the paper edge.
Page 249: Test Pattern Print
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.15 Test pattern print When push the [SelecType] key in the serial number input screen, it moves to the next screen. (When display "No.1:PEG**000000",it moves Print the adjustment pattern and confirm the various adjustment items also input the "No.2:PEG**000000".)
Page 250: Print Head Cleaning
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.16 Print head cleaning The [Enter] key will not be effective if the cartridges are not completely inserted after the cartridges have been fully removed during display of "Please Dischg. I/ This is the item that is carried out at the time of the end of the production process or C,"...
Page 251: Counter Clear
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.4.17 Counter clear Table 5-13. Counter that is cleared Initial value Perform the initialization of the software counter of waste ink counter etc. The implementation of this item is permitted to only at the time of factory shipment.
Page 252: Cleaning
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.5 Cleaning 5.4.5.1 Normal cleaning KK0 Perform the normal cleaning KK0. Perform the cleaning of the head. Figure 5-75 showing the menu sequence. Table 5-14 showing the items. Figure 5-74 showing the cleaning menu sequence.
Page 253: Print
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.6 Print 5.4.6.1 Check pattern Print the check pattern. Print the test pattern and the Adj. variable. Figure 5-80 showing the check pattern print menu sequence. Table 5-15 showing the items.
Page 254: Parameter
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.7 Parameter Using this menu you can reset or change the parameters for the printer mechanism Item controls. However, the parameter on this menu can also be modified from the...
Page 255: Initialize The Parameter
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.7.1 Initialize the parameter Table 5-17. Initialize items Item Description Initialize the parameter. PF distance correction 1~3 Following table showing the items. Serial number Number of wiping (each head) Figure 5-83 showing the initialize the parameter menu sequence.
Page 256 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Item Item SelecType Enter Init.: Wiping Record Initialize OK? Ini. : All SelecType Pause SelecType Item Item Init.: Rubbing Record Initialize Parameter Ini. : Capping Position SelecType SelecType Item Item Init.: West Ink Record...
Page 257: Update Parameter
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.7.2 Update parameter Cap position Update the adjustment parameter. Update the cap position parameter. Figure 5-84 showing the update parameter menu sequence. Following figure showing the update cap position parameter menu sequence.
Page 258 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Head Rank Print position The panel input of 5.4.4.3 "Head Rank input" is possible implement about head rank Update the parameter of the Bi-D print position and the Gap position.
Page 259 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Item SelecType Adjustable with "Paper Feed +/ Adjustable with "Paper Feed +/ BiD 300, V2, C 0 Gap 240, V1, LM 0 -" key at unit of 1/2880 inch.
Page 260 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Paper transportation distance Mechanical parameter Update the paper transportation distance parameter. Update the mechanical parameter. Figure 5-88 showing the paper transportation distance parameter update menu Figure 5-89 showing the mechanical parameter update menu sequence.
Page 261 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com [H to Cut] is the distance between the LC#1 to the cutter. Ink parameter [E to H] is the distance between the edge sensor to the LC#1 head. Update the ink parameter.
Page 262: Parameter Display
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.8 Reliability Test 5.4.7.3 Parameter display Display the parameter of designated address. Perform the reliability test of the mechanism and the head. Figure 5-90 showing the parameter display menu sequence.
Page 263 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Item Life : CR Motor SelecType Item Item Life : PF Motor Life : Printing SelecType SelecType Item Item Life : Shutter Life : CR+PF Motor SelecType SelecType Item...
Page 264: Cr Motor
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.8.1 CR Motor 5.4.8.2 PF Motor Perform the CR motor reliability test. Perform the PF motor reliability test. The carriage runs with the round trip designated number at designated speed.
Page 265: Cr + Pf Motor
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.8.3 CR + PF Motor As for the parameter of CCW, [240CPS], [300CPS], [400CPS], and [800CPS] are possible select. Perform the CR motor and the PF motor simultaneous reliability test.
Page 266: Cutter
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.8.4 Cutter Perform the cutter reliability test. Perform the cut designated number at designated parameter. When the reliability number is [-1], reliability is repeated until key is input. Adjustable with "Paper Feed +/-"...
Page 267: Head Up / Down
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.8.5 Head Up / Down 5.4.8.6 Head lock Perform the head up / down reliability test. Perform the head lock reliability test. Perform the capping designated number. Perform the head lock (cancel / set) designated number.
Page 268: Lever Lock
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.8.7 Lever lock 5.4.8.8 Cleaning Perform the lever lock reliability test. Perform the cleaning reliability test. Perform the lever lock (cancel / set) designated number. Perform the cleaning designated number.
Page 269: Print
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.8.9 Print 5.4.8.10 Shutter Perform the print reliability test. Perform the shutter reliability test. Perform the pattern print designated number. Perform the shutter actuation designated number. When the reliability number is [-1], reliability is repeated until [Pause] key is input.
Page 270: Total Reliability
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.8.11 Total reliability As for the parameter of CW, [240CPS], [300CPS], [400CPS] and [800CPS] are possible select. Perform the CR axis (motor, bearing, tube etc.), the PF axis, the CR axis + the PF axis,...
Page 271: Life Confirmation
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 5.4.8.12 Life confirmation Confirm the number of endurance. You can confirm the endurance record any time because this record is storage in NVRAM. Figure 5-104 showing the reliability number confirmation test menu sequence.
Page 272: Chapter 6 Maintenance
Thank You For Using TheServiceManualShop.com C H A P T E R MAINTENANCE Thank You For Using TheServiceManualShop.com...
Page 273: General Maintenance Issues
Basically for this product, service technicians are required to visit the user’s location Due to the printer’s size and weight, make sure any area you where the EPSON Stylus Pro 10000/10000CF is used, and perform necessary move the printer to or any surface you place the printer on is maintenance/service on-site while following the precautions below.
Page 274: Periodic Maintenance Items
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 6.1.1 Periodic Maintenance Items 6.1.2 Product Life Information The printer uses sensors and counters to determine when consumable items need to be The information regarding the life of the main body / each system department / part in replaced.
Page 275: Printing Output At The Time Of Maintenance
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 6.1.3 Printing output at the time of maintenance Waste ink unit (pads) Cleaning unit Printing of the nozzle checking pattern / status sheet Do the panel switch operation shown below, after confirm that the LCD display of the operation panel is displayed "READY".
Page 276 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 6-3. Status sheet Item Panel display Setting value Contents The firmware version of the Version of the firmware VERSION TOxxxx. yyyy .zzzz printer is displayed. The ink used quantity in the page Before page ink used quantity xx.x g...
Page 277 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 6-3. Status sheet *1 : The meaning of the command of the ink remainder quantity and cutter life are as follows. Refer to 4.2.1.2. Item Panel display Setting value Contents Table 6-4.
Page 278: Maintenance Inspection Items
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 6.2 Maintenance inspection items Is there ink leakage in the coupling part under the damper bracket? Do the inspection and necessary treatment at the time of the service enforcement about the following item 1 - 8.
Page 279 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com (2) The guide rail department / Ink cartridge holder department (Refer to 4.2.3.7) Are 3 waste ink tubes fixed to the clamp on the flushing box? Guide rail Clamp Figure 6-7.
Page 280 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Are 2 waste ink tubes fixed to the tube clamp? Is there ink dirt in the bottom of the cleaning unit (the absorption material attachment department)? Clamp Tube Dot missing detector Cleaning unit Figure 6-10.
Page 281 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 2.2 Air tube : Confirm the air tube and compressor department that are jointed to ink Does the ink valve solenoid on each ink holder work smoothly? pump Assy. (Refer to 4.2.3.16)
Page 282 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 3.2 Cutter : Confirm the cutter solenoid actuation with manually pushing. (Refer to Is there looseness in the set screw of the bearing stopper that is attached to the CR 4.2.3.4)
Page 283 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Is there abrasion in the gear (aluminum) that is attached to the PF motor axis? Is there ink dirt in the sub platen? CR driven pulley PF roller PF driven roller...
Page 284 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com CR_HP sensor (Refer to 4.2.3.21) Paper release sensor (Refer to 4.2.3.22) 5. Form conveyance path P_FRONT sensor (Refer to 4.2.3.23) Is there the dirt of paper powder etc. in the Paper guide U? P_REAR sensor (Refer to 4.2.3.24)
Page 285: Chapter 7 Appendix
Thank You For Using TheServiceManualShop.com C H A P T E R APPENDIX Thank You For Using TheServiceManualShop.com...
Page 286: Wiring Diagrams
CN15 CN16 CN30 CN24 CN21 CN31 CN28 C362Main CN23 CN32 CN20 Board CN33 CN22 C362DRV CN50 CN19 CN34 Board CN27 CN36 CN37 CN38 CN26 Figure 7-1. EPSON Stylus Pro 10000/10000CF Wiring Diagram Thank You For Using TheServiceManualShop.com Appendix Wiring Diagrams...
Page 287 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 7-1. C362DRV Board Connectors Table 7-1. C362DRV Board Connectors Connector # Pins Color Connection Connector # Pins Color Connection CN35 2 (Red / Black) Dot Missing Detector 3 (Black / Grey / White)
Page 288: Parts Reference List
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 7.2 Parts Reference List Table 7-2. Parts Reference List Ref No. Sales Part Code Description 1063147 SENSOR BASE PR Table 7-2. Parts Reference List 1063162 PAPER GUIDE U Ref No.
Page 289 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 7-2. Parts Reference List Table 7-2. Parts Reference List Ref No. Sales Part Code Description Ref No. Sales Part Code Description 1063139 ROLL DAMPER L ASSY 1063204 HEAD ADJUSTOR SPRING...
Page 290 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 7-2. Parts Reference List Table 7-2. Parts Reference List Ref No. Sales Part Code Description Ref No. Sales Part Code Description 2047882 P THICK SENSOR CABLE ASSY 1063183...
Page 291 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 7-2. Parts Reference List Table 7-2. Parts Reference List Ref No. Sales Part Code Description Ref No. Sales Part Code Description 1063207 SUS SUPPORT 1063231 H TOP COVER...
Page 292 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 7-2. Parts Reference List Ref No. Sales Part Code Description 1053560 FLANGE(2 INCH) 1071283 PACKING BOX ASSY(ABROAD) 1071285 PAPER OUT TRAY 1071286 CASTER(STOPPER) 1071287 CASTER(NON STOPPER) Thank You For Using TheServiceManualShop.com...
Page 293: Exploded View Diagram
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 7.3 Exploded View Diagram The exploded view diagram of this machine are shown after the next page. Furthermore, refer to the number that is allotted to each part in the figure, because it is corresponding in the figure number in the table of the parts list.
Page 294 101 X2 121 X 4 120 x 4 102 x 3 109 x 2 110 x 4 111 x 5 113 X 3 Thank You For Using TheServiceManualShop.com 114 X 3 PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.1 Rev.01 10282...
Page 295 FRAME ASSY (2) Thank You For Using TheServiceManualShop.com 152 X 2 153 X 2 176 X 3 Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.2 Rev.01 10282...
Page 296 HEAD ASSY Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.3 Rev.01 10282...
Page 297 CR RALE ASSY Thank You For Using TheServiceManualShop.com 120 X 2 Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.4 Rev.01 10282...
Page 298 VACUUM SWITCH ASSY Thank You For Using TheServiceManualShop.com 410 X 4 407 x 5 405 X 10 406 X 11 Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.5 Rev.01 10282...
Page 299 INK SYSTEM ASSY Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.6 Rev.01 10282...
Page 300 612 X 12 613 X 6 512 X 6 518 X 3 515 X 6 120 x 5 501 X 6 517 X 2 502 X 6 Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.7 Rev.01 10282...
Page 301 612 X 12 611 X 12 613 X 6 611 X 6 612 X 6 619 X 6 612 x 6 611 x 6 620 X 2 Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.8 Rev.01 10282...
Page 302 BOARD BASE ASSY Thank You For Using TheServiceManualShop.com 705 X 2 175 X 12 120 x 18 709 X 2 713 for JPN 704 X 2 Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.9 Rev.01 10282...
Page 303 COVER ASSY Thank You For Using TheServiceManualShop.com 804 x 3 Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.10 Rev.01 10282...
Page 304 SPINDLE ASSY Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com PM10,MC10 / EPSON STYLUS PRO 10000,10000CF No.11 Rev.01 10282...
Page 305: Component Layout
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 7.4 Component Layout The illustrations below show the control circuit board component layout of this machine. Figure 7-2. C362MAIN Board Component Layout Thank You For Using TheServiceManualShop.com Appendix Component Layout...
Page 306 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Figure 7-3. C362SUB Board Component Layout Thank You For Using TheServiceManualShop.com Appendix Component Layout...
Page 307 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Figure 7-4. C83322 Board Component Layout (1/2) Figure 7-5. C83322 S Board Component Layout (2/2) Thank You For Using TheServiceManualShop.com Appendix Component Layout...
Page 308 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Figure 7-6. C362DRV Board Component Layout (1/2) Thank You For Using TheServiceManualShop.com Appendix Component Layout...
Page 309 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Figure 7-7. C362DRV Board Component Layout (2/2) Thank You For Using TheServiceManualShop.com Appendix Component Layout...
Page 310: Circuit Diagram
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 7.5 Circuit Diagram The illustrations below show the control circuit board circuit diagram of this machine. Thank You For Using TheServiceManualShop.com Appendix Circuit Diagram...
Page 311 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com The circuit diagrams of the printer are followings; NO.1 C362DRV board NO.2 C362DRV board NO.3 C362DRV board NO.4 C362DRV board NO.5 C362DRV board NO.6 C362MAIN board NO.7 C362SUB board NO.8...
Page 312 Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com...
Page 313 Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com...
Page 314 Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com...
Page 315 Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com...
Page 316 Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com...
Page 317 Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com...
Page 318 Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com...
Page 319 Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com...
Page 320 Thank You For Using TheServiceManualShop.com Thank You For Using TheServiceManualShop.com...
Page 321: Chapter 8 Stylus Pro 10600
Thank You For Using TheServiceManualShop.com C H A P T E R Stylus Pro 10600 Thank You For Using TheServiceManualShop.com...
Page 322 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com This chapter presents information that is unique to the EPSON Stylus Pro 10000/ 10000CF. It also clarifies cautionary items for use of HC2/AY ink in HCD/PPI models. The chapter structures information by the following sections.
Page 323: Product Description
1865 (W) x 1222 (H) x 680 (D) 8.1.1 Product Description Weight 131Kg (including the standard stand) This section explains the feature on the specification of EPSON Stylus Pro 10000/ 10000CF. Feature of the software Basic Specifications Change the Drive board Complies with Multi-Protocol Ethernet I/F Card Firmware version 2.14 or later.
Page 324 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com NOTE: One draining cartridge is packed with the printer unit, but draining cartridges for all colors (7 total) are necessary when replacing the head during servicing. Reliability Total print volume...
Page 325: Function
LOAD PAPER Panel Setting Mode is entered, operated and terminated by same methods used with the Paper jam PAPER JAM Stylus Pro 10000/10000CF. (Refer to 1.6 "SelecType Settings") Front cover open FRONT COVER OPEN The table below shown the SelecType Menus.
Page 326 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Printer Setting Menu Table 8-6 shown the Printer Setting Menus. Table 8-6. Printer Setting Menus Setting Item LCD panel Display Setup Values Detail Reference PG Setting PLATEN GAP NARROW, AUTO, WIDE Adjusts the platen gap.
Page 327 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com PG Setting Interface Select Selecting this mode allows the user to set the platen gap. The relationship between Selecting this mode allows selection of the parallel / USB, or optional interface-1 / panel setting, command setting (SN command), and actual platen gap position is 2, or automatic interface selection.
Page 328 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Nozzle Check Pattern Printing Test Print Menu Selecting this mode allows the user to print the firmware version, the waste ink Table 8-8 shown the Test Print Menus. counter value and the nozzle check pattern. "PAT PRINTING" is displayed during printing pattern.
Page 329 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Status printing Job information printing Selecting this mode allows the user to print the current panel settings. Selecting this mode allows the user to print job information (max of 10 jobs) saved "PAT PRINTING"...
Page 330 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Printer Status Menu Table 8-9 shown the Printer Status Menu. Table 8-9. Printer Status Menu Display Item LCD panel display Detail Setup Values Reference Firmware version Display the firmware version T0xxxx.
Page 331 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Firmware version Amount of ink used in each job is displayed. Firmware version is displayed as following, Clear Job History <Display sample> "Ver.TP0xxxx.yyyy.zzzz" Selecting this mode allows to clear the job history saved in the printer.
Page 332 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Head unit life monitor Totals the discharge shots for each color, calculates the number of guaranteed discharge shots for each nozzle x 180 as life, further calculates the maximum number of shots for each color, and displays the results.
Page 333 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-11 shown the User Paper Setup Menus. User Paper Setup Menu Table 8-11. PAPER CONFIG. Menu Selecting this mode allows detection of the thickness of the available paper, and...
Page 334 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-12 shown the paper setup and corresponding operation. NOTE1: (*1) If `STD` is selected on Paper select, Paper Thickness Detection Pattern Print and Paper Thickness No. Select may not be displayed. It Table 8-12.
Page 335 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Black Ink Change NOTE: Panel message: "REMOVE DRAIN CRTG" it is displayed until drain cartridge is removed. Selecting this mode allows the exchange of photo black ink and matte black ink.
Page 336 Selecting this mode allows the user to Bi-D and Uni-D adjustment for each paper Select the gap adjustment menu from the panel. thickness. Set to "STD" when using EPSON paper (0.2mm or 1.2mm thick). For other paper, Table 8-15 shown the gap ajustment menu. set thickness in units of 0.1mm.
Page 337 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Adjustment method NOTE4: (*2) When paper thickness is set as more than 0.6mm, PG2.6mm is set regardless of PG setting and paper thickness sensor detection. The adjustment value set above is saved in NVRAM. Such adjustment value is NOTE5: (*3) Even if paper thickness is detected as thick paper (more than adjusted to 4 types of PG height (1.4mm/2.1mm/2.6mm).
Page 338: Maintenance Mode 1
Maintenance Mode 1 is entered, operated and terminated by same methods used with the Stylus Pro 10000/10000CF. (Refer to 1.7 "Maintenance Mode 1") Table 8-18 shown the Maintenance Mode 1 setup items.
Page 339 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-18. Maintenance Mode 1 Setup Items Item Panel Display Item Menu 1 Panel Display Item Menu 2 Panel Display Setup Values Logo display "EPSON" MANUFACT K BLACK(HC2/AY) / PHOTO...
Page 340 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-18. Maintenance Mode 1 Setup Items Item Panel Display Item Menu 1 Panel Display Item Menu 2 Panel Display Setup Values Logo display "EPSON" MANUFACT LC Ink color...
Page 341 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-18. Maintenance Mode 1 Setup Items Item Panel Display Item Menu 1 Panel Display Item Menu 2 Panel Display Setup Values Paper feed adjustment conversion system table 1 <nn>...
Page 342 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Hexadecimal Dump Parallel Interface mode The hex dump function allows data sent to the printer to be printed and displayed in Selecting this mode allows the user to select receiving speed of parallel interface either hexadecimal format.
Page 343 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Initialize panel setup value MW7 balance setup Selecting this mode allows users to initialize panel setup value to default. By setting minimum value for anomalous M/W feeding at this location, generation of banding due to mechanical irregularities is kept to a minimum.
Page 344 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Ink cartridge information SN menu Paper feed adjustment table It displays ink information recorded in CSIC. m2 value set by mechanism sequence command "Paper feed adjustment" is converted Table 8-23. Ink Cartridge Information to the actual paper feed adjustment value with paper feed adjustment table saved in NVRAM.
Page 345 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Paper feed adjustment offset User Table Initialization Selecting this menu allows the users to initialize paper feed adjustment conversion Offset value is set to add to the actual paper feed adjustment value.
Page 346: Maintenance Mode 2
Maintenance Mode 2 is entered, operated and terminated by same methods used with Cutter life total counter value 0 ~ 4294967295 (Decimal) the Stylus Pro 10000/10000CF. (Refer to 1.8 "Maintenance Mode 2") CUTTER TOTAL Total prints counter value TTL PAGES 0 ~ 4294967295 (Decimal) Table 8-24 shown the Maintenance Mode 2 setup items.
Page 347 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Initialize RTC Counter initialize menu Selecting this mode allows the user to set RTC initialized time to NVRAM. This section explains the Counter Initialize Menu. The table below shows items that The panel display is following;...
Page 348 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com NVRAM counter value indication Table 8-27. Adjustment / setup menu Selecting this mode allows the user to indicate each life counter in decimal. Adjustment / Setup Item Panel Display...
Page 349 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Change of adjustment value Failed nozzle limit (dye/pigment/HC2/HCD/PPI) In case of nozzle check error with auto nozzle check, nozzle check error doesn’t <Format> "XXx=nn:mm" occur until it meets following condition permitting optional number of nozzle •...
Page 350 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Ink cartridge CSIC detection level setup (ED MODE setup) CR speed adjustment for Bi-D print on specific media Selecting this mode allows the user to adjust CSIC detection level. Each This setting allows adjustment of CR speed for Bi-D printing (only at 720x720/ adjustment value indicates as following;...
Page 351 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Running time, status relations Maintenance information menu Table 8-32. Running Time, Status Relations (MENU E) This menu reads out needed information for printer maintenance. Item Panel Display Setup Values Table 8-31.
Page 352 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Carriage Table 8-34. Ink System 1 (MENU S) Item Panel Display Setup Values Table 8-33. Carriage (MENU R) AY → HC2 replacement times <nnnnnnnnn> Item Panel Display Setup Values AY →...
Page 353 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-35. Ink System 2 (MENU Y) Head Item Panel Display Setup Values Table 8-36. Head (MENU H) Failed dot detection NG times while power ON (C) <nnnnnnnnn> Item...
Page 354 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Ink 1 Ink 2 Table 8-38. Ink 1 (MENU A) Table 8-39. Ink 2 (MENU B) Item Panel Display Setup Values Item Panel Display Setup Values K (include dye Each color ink replacement date (Black this time) <YY><MM><DD>...
Page 355 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-39. Ink 2 (MENU B) Table 8-40. Paper information (MENU P) Item Panel Display Setup Values Item Panel Display Setup Values Paper ejection times of each paper size Each color ink vendor (LgtMagenta last time) <xxxxxxxxxxxxxxxxx>...
Page 356 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-40. Paper information (MENU P) Print mode Item Panel Display Setup Values Table 8-41. Print mode (MENU M) Paper ejection times of each paper size <nnnnnnnnn> Item Panel Display...
Page 357 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-42. Panel setup information (MENU O) Table 8-43. Fatal error (MENU F) Item Panel Display Setup Values Item Panel Display Setup Values Paper feed adjustment change times Service call history 7 (Type) <nnnnnnnnn>...
Page 358 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-44. Normal error (MENU N) Maintenance information initialization menu Item Panel Display Setup Values It operates initialization (counter clear) of each maintenance menu. Normal error history 8 (Date) <YY><MM><DD>...
Page 359: Troubleshooting
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 8.2 Troubleshooting Table 8-48. Status Reply priority Priority Status When troubleshooting, see Chapter 3 "Troubleshooting." Front cover open This section describes information that is unique to Stylus Pro 10600, and it should be Type-B I/F error applied in conjunction with Chapter 3 information.
Page 360 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-49. Indicators (LED) List Indicators (LED) List Displayed functions LED Status Stylus Pro 10600 LED indicator table shown in Table 8-49. Print ready In SelecType mode Table 8-49. Indicators (LED) List...
Page 361: Fatal Errors
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 8.2.2 Fatal Errors Table 8-50. Fatal Error Code List Code Description Table 8-50. Fatal Error Code List 00010017 Liquid sensor overflow (M) Code Description 00010018 Liquid sensor overflow (LC)
Page 362 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Table 8-50. Fatal Error Code List SERVICE REQ. 00000102: Right side waste ink box full SERVICE REQ. 00000103: Left side waste ink box full Code Description 0002000D Program load error...
Page 363 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com SERVICE REQ. 0003xxxx: Program error SERVICE REQ. 10000180: CPU reservation instruction code exception SERVICE REQ. D0xxxxxx: Program error error Problem Problem Error not expected during program operation. (Can also be generated during board Board failure, CPU solder failure.
Page 364: Maintenance Call
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 8.2.3 Maintenance call SERVICE REQ. 10000xxx: CPU error Problem MAINTENANCE REQ. 0105: Head unit life Board failure, CPU solder failure. Program malfunction, generation mistake. Problem Solution Head unit life. (28 billion shots per nozzle) Replace drive board.
Page 365 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com MAINTENANCE REQ. 0108 Problem SSCL has reached rotation limit (200 rotations) Counting panel executions as 3 and periodic executions as 1, SSCL execution from the panel is disabled when 198 rotations has been reached, and this maintenance call is displayed for several seconds when "EXEC"...
Page 366: Adjustment
When performing adjustments, see Chapter 5 "Adjustments." Pro 10000/10000CF. See Chapter 5 "Adjustments" before continuing. This section This section describes information that is unique to EPSON Stylus Pro 10000/ describes information that is unique to Stylus Pro 10600. 10000CF, and it should be applied in conjunction with Chapter 5 "Adjustments"...
Page 367: Bi-D Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 8.3.1.2 Bi-D adjustment Pause Performs alignment of Bi-D printing positions by PG small. [Enter] Adjust Print Performs alignment of Bi-D printing positions for each color of heads 1~3. Adjustment prints in Bi-D and from the results inputs errors for CW printing positions Enter and CCW printing positions.
Page 368 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com When press the "Enter" button during the "BiD End" display, operation mode shift to the "Adj: Head LR Adj.". Print all of the test pattern when "Enter" button is pressed during the "[Enter] Adjust Print"...
Page 369: Head Lr (Head Gap) Adjustment
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 8.3.1.3 Head LR (Head gap) adjustment Pause Performs correction of head gap. Adjustment prints in Uni-D and from the results inputs a correction value. [Enter] Adjust Print In addition, the types of waveforms to be adjusted differs according to the cartridges...
Page 370 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Print pattern Adjustable with "Paper Feed +/-" Gap 300, V2, M button at unit of 1/2880 inch. Item SelecType Adjustable with "Paper Feed +/-" Gap 300, V2, LC button at unit of 1/2880 inch.
Page 371: Print Head Cleaning
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 8.3.1.4 Print head cleaning NOTE1: During display of "Please Drain. C" "Set Cleaning I/C" "Please Drain. C (2)" if all cartridges are not inserted after removal of all previous This is the item that is carried out at the time of the end of the production process or cartridges, the [Enter] button will not function.
Page 372: Update Parameter
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 8.3.1.5 Update parameter Print position Update the adjustment parameter. Performs updating of parameters for Bi-D printing position alignment and head gap Figure 8-11 showing the update parameter menu sequence.
Page 373 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Item SelecType Adjustable with "Paper Feed +/-" Adjustable with "Paper Feed +/-" BiD V2, C 0 Gap 240, V1, LM 0 button at unit of 1/2880 inch. button at unit of 1/2880 inch.
Page 374 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Print position 2 Performs updating of parameters for Bi-D printing position alignment in PG medium. Figure 8-13 showing the print position 2 menu sequence. Adjustable with "Paper Feed +/-"...
Page 375 EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com Print position 3 Performs updating of parameters for Bi-D printing position alignment in PG very small. Figure 8-14 showing the print position 3 menu sequence. Adjustable with "Paper Feed +/-"...
Page 376: Maintenance
EPSON Stylus Pro 10000/10000CF/10600 Revision D Thank You For Using TheServiceManualShop.com 8.4 Maintenance 8.4.2 Life Information Information about life of Stylus Pro 10600 printer/mechanisms/components is shown When performing maintenance, see Chapter 6 "Maintenance." in Table 8-54. This section describes information that is unique to Stylus Pro 10600, and it should be applied in conjunction with Chapter 6 information.

This manual is also suitable for:

Stylus pro 10000cf Stylus pro 10600

Epson Stylus Pro 10000 Service Manual

Chapter 1 Product Description

Chapter 2 Operating Principles

Chapter 3 Troubleshooting

Chapter 4 Disassembly & Assembly

Chapter 5 Adjustment

Chapter 6 Maintenance

Chapter 7 Appendix

Chapter 8 Stylus Pro 10600

Quick Links

Troubleshooting

Related Manuals for Epson Stylus Pro 10000

Summary of Contents for Epson Stylus Pro 10000