Table of Contents
Advertisement
English
Intended Use
These rivet tools are designed for installation blind fasteners.
DO nOT insert any objects other than the rivets specified in the
instruction manual into the nosepiece.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These rivet tools are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D
WALT battery packs include a fuel gauge, which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button
15
. A combination of the three green LED lights will
illuminate, designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
10
WALT batteries and chargers.
e
is fully charged.
11
12
and firmly pull the
Mounting the Nosepiece (Fig. C)
1. Select the correct nosepiece for the rivet to be installed.
Refer to the number or letter
the Rivet Size Chart to select the proper nosepiece for
the application.
2. Unscrew and remove the screw cap
3. Place the nosepiece
1
4. Screw the screw cap onto the nose housing.
Rivet Size Chart
Nosepiece
1
2
3
4
A
B
C
Mandrel Collector and Spare Nosepiece
Holder (Fig. D)
WARNING: Do not use the tool without the mandrel
collector attached.
The mandrel collector
5
and spare nosepiece holder
to the rear of the tool.
The tool can be used without the spare nosepiece holder.
To remove the mandrel collector or spare nosepiece holder,
unscrew them until they are removed. If you are using the tool
with the spare nosepiece holder, attach it to the tool first, and
then attach the mandrel collector.
Belt Hook (Fig. E)
Included with Some Models
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook for
tethering or securing the tool to a person or object during
use. DO NOT suspend tool overhead or suspend objects
from the belt hook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.
iMPORTAnT: When attaching or replacing a belt hook, use only
the screw that is provided. Be sure to securely tighten the screw.
A belt hook
21
can be attached to either side of the tool
using only the screw
22
provided, to accommodate left‑ or
right‑handed users. If the belt hook is not desired at all, it can be
removed from the tool.
on the nosepiece and
16
2
.
into the nose housing
.
3
Rivet Diameter
mm
Inches
DCF403
2.4
3/32
3.2
1/8
4.0
5/32
4.8
3/16
DCF414
4.8
3/16
6.0
15/64
6.4
1/4
6
attach
Advertisement
Table of Contents
