Sealey SA201 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
‰
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Only use impact sockets which are specifically designed for use with an impact wrench.
9
Wear approved safety eye/face shield, ear defenders and hand protection.
9
WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we
‰
recommend you wear suitable respiratory protection.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non-essential persons away from the working area.
9
DO NOT use the wrench for a task it is not designed to perform.
8
WARNING! DO NOT use wrench if damaged or thought to be faulty (contact Service Agent).
‰
DO NOT use wrench unless you have been instructed in its use by a qualified person.
8
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
8
DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry wrench with your hand on the trigger in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. INTRODUCTION
Combination of composite materials, alloyed metals and twin hammer design, result in a lightweight, durable and powerful air impact wrench.
Composite handle helps reduce the effects of vibration and chill. Handle exhaust reduces noise output and limits the circulation of brake
dust on wheel applications. Fingertip control of power and direction via lever on rear of wrench. Suitable for garage, tyre shop and workshop
applications.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA201
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . 7cfm
Breakaway Torque: . . . . . . . . . . . . . 590lb.ft (800Nm)
Drive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/2"Sq
Free Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . 8500rpm
Inlet Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Maximum Torque: . . . . . . . . . . . . . . . . 450lb.ft (610Nm)
Noise Power/Pressure:. . . . . . . . . . . . . . . . 107/96dB(A)
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . .90psi
Vibration/Uncertainty: . . . . . . . . . . . . . . . . . . 4.0/2.0m/s²
Nett Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.05kg
© Jack Sealey Limited
AIR IMPACT WRENCH
1/2"SQ DRIVE COMPOSITE TWIN HAMMER
MODEL NO:
Wear protective Wear ear
gloves protection
Original Language Version
SA201
Wear a mask
SA201 | Issue 1 30/01/19