LG 32LG40-UG Service Manual page 12

O HDMI-III [C/S : 4607]
EDID Block 0 table =
0 1 2 3 4 5
0 00 FF FF FF FF FF
10 00 12 01 03 80 73
20 09 48 4C 21 08 00
30 01 01 01 01 01 01
40 36 00 C4 8E 21 00
50 40 80 37 00 C4 8E
60 3F 1F 3C 09 00 0A
70 00 4C 47 20 54 56
EDID Block 1 table =
0 1 2 3 4 5
0 02 03 18 F1 47 84
10 67 03 0C 00 30 00
20 6E 28 55 00 C4 8E
30 16 20 58 2C 25 00
40 20 E0 2D 10 10 3E
50 D0 8A 20 E0 2D 10
60 26 36 80 A0 70 38
70 00 1A 00 00 00 00
O
RGB [C/S : 1467]
EDID Block 0 table =
0 1 2 3 4 5
0 00 FF FF FF FF FF
10 00 12 01 03 68 73
20 09 50 4E A1 08 00
30 01 01 01 01 01 01
40 35 00 C4 8E 21 00
50 40 80 37 00 C4 8E
60 3F 1F 3C 09 00 0A
70 00 4C 47 20 54 56
EDID Block 1 table =
0 1 2 3 4 5
0 02 03 04 00 66 21
10 BA 88 21 00 00 1E
20 00 00 00 00 00 00
30 00 00 00 00 00 00
40 00 00 00 00 00 00
50 00 00 00 00 00 00
60 00 00 00 00 00 00
70 00 00 00 00 00 00
Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
6 7 8 9 A B C
FF 00 1E 6D 01 00 01
41 96 0A CF 74 A3 57
01 01 01 01 01 01 01
1B 21 50 A0 51 00 1E
00 1E 0E 1F 00 80 51
21 00 00 1E 00 00 00
20 20 20 20 20 20 00
0A 20 20 20 20 20 20
6 7 8 9 A B C
05 03 02 20 22 10 23
B8 2D 01 1D 00 72 51
21 00 00 1E 01 1D 80
C4 8E 21 00 00 9E 8C
96 00 C4 8E 21 00 00
10 3E 96 00 13 8E 21
1F 40 30 20 25 00 C4
00 00 00 00 00 00 00
6 7 8 9 A B C
FF 00 1E 6D 01 00 01
41 96 0A CF 30 A3 57
01 01 01 01 01 01 01
1B 21 50 A0 51 00 1E
00 1E 0E 1F 00 80 51
21 00 00 1C 00 00 00
20 20 20 20 20 20 00
0A 20 20 20 20 20 20
6 7 8 9 A B C
56 B0 51 00 1B 30 40
00 00 00 00 00 00 00
00 00 00 00 00 00 00
00 00 00 00 00 00 00
00 00 00 00 00 00 00
00 00 00 00 00 00 00
00 00 00 00 00 00 00
00 00 00 00 00 00 00
5. White Balance
5-1. Summary
D E F
(1) Purpose: to reduce the difference in color temperature
01 01 01
among modules
4C B0 23
(2) Principal: A module is in full dynamic range when RGB
01 01 01
Gain on OSD is 192. To adjust the white balance without
30 40 88
causing full dynamic range and full data, fix one of RGB
00 1E 30
Gains at 192 and control the other two by reducing them
FD 00 38
from 192.
00 00 FC
20 01 46
5-2. Required Equipment
(1) Color Analyzer : CA-210 (NCG : CH 9 / WCG : CH12)
(2) Automatic adjuster (with automatic adjustment necessity
D E F
and the RS-232C communication being possible)
15 07 50
(3) Remote control for adjustment
D0 1E 20
(4) Video Signal Generator MSPG-925F 720p,/216Gray
18 71 1C
(Model : 217, Pattern 78)=> Applied only when the inner
0A D0 8A
pattern cannot be used
18 8C 0A
* Use the Color Analyzer with the matrix calibrated by the CS-
00 00 18
1000
8E 21 00
00 00 07
D E F
01 01 01
4C B0 23
01 01 01
30 48 88
00 1E 30
Connection Diagram of Automatic Adjustment
FD 00 38
00 00 FC
20 00 14
5-3. Adjustment command (Protocol)
(1) Protocol
<Command Format>
D E F
70 36 00
00 00 00
00 00 00
- LEN : Number of Data Byte
00 00 00
- CMD : Command
00 00 00
- VAL : Value of FOS Data
00 00 00
- CS : Checksum
00 00 00
- A : Acknowledge
00 00 67
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX}
- 12 -
Probe
RS -232C
Signal Source
* Not used when the inner pattern of the TV set is used
LEN CMD
Co lo r Analyzer
RS -232C
Co m p ut er
RS -232C
Pat t ern Generat o r
CS
VAL
LGE Internal Use Only