Bosch Active Line Original Operating Instructions page 45

To charge the eBike battery, read and follow the instructions
in the operating manual for the charger.
The eBike battery can be charged at any state of charge. In-
terrupting the charging process does not damage the eBike
battery.
The eBike battery has a temperature monitoring function
that only allows it to be charged within a temperature range
of 0 °C to 40 °C.
Do not reconnect the eBike battery to the charger until it has
reached the correct charging temperature.
Battery charge indicator outside of the eBike
Note: The PowerMore battery charge indicator (2) switches
back off as soon as the eBike battery is switched on.
The five LEDs on the battery charge indicator (2) show the
battery's state of charge when the eBike battery is switched
on.
Each LED represents approximately 20 % of the charging ca-
pacity. When the eBike battery is fully charged, all five LEDs
will be lit.
The eBike battery's state of charge when switched on is also
shown on the display of the on-board computer. Read and
follow the instructions in the operating manuals for the drive
unit and on-board computer.
If the eBike battery's capacity is less than 10 %, the last re-
maining LED will flash.
Once charging is complete, disconnect the eBike battery
from the charger and the charger from the mains.
Laying the Cable on the PowerMore Battery
Holder (see figure A)
Note: When laying the cable (6), make sure that the
cable (6) is fed under the release button (10). This prevents
the release button (10) from being pressed accidentally and
causing the PowerMore battery to be released.
Inserting and Removing the PowerMore Battery
When inserting the battery into the holder or remov-
u
ing it from the holder, always switch off the eBike bat-
tery and the eBike beforehand.
Once you have inserted the eBike battery, check that
u
it is correctly positioned and secure in all directions.
Only leave the PowerMore battery with the cable con-
u
nected to the eBike.
Once the PowerMore battery is installed, the connec-
u
tion socket of the battery must not face upwards.
Bosch eBike Systems
If the temperature of the
eBike battery is outside this
charging range, three of the
LEDs on the battery charge
indicator (2) will flash. Dis-
connect the eBike battery
from the charger and let it
reach the correct temperat-
ure range.
Inserting the PowerMore Battery (see figure B)
To insert the battery (1), place its guide grooves (12) onto
the guide rails (11). Ensure that the battery is aligned cor-
rectly and that the battery is positioned in both guide rails.
Slide the battery (1) into the holder (9) until it audibly clicks
into place.
Insert the cable connector (4) into the connection
socket (3). Ensure that the cable connector (4) is aligned
correctly.
Insert the cable connector (7) into the eBike charging
socket (8). Ensure that the cable connector (7) is aligned
correctly.
Secure the cable (6) in place as directed by the eBike manu-
facturer (e.g. with cable clips).
Removing the PowerMore Battery (see figure C)
Firstly, disconnect the cable (6) by opening the cable lock as
directed by the eBike manufacturer.
Pull the release mechanism (14) towards you ❶ and remove
the cable connector (7) from the eBike charging socket ❷.
Press the release buttons (13) and remove the cable con-
nector (4) from the connection socket.
To remove the battery (1), press the release button (10)
and pull the battery (1) sideways out of the holder (9).
Note: As a result of varying designs, the PowerMore battery
may need to be inserted and removed using a different
method. Read the eBike manufacturer's operating instruc-
tions for how to do this.
Operation
Start-up
Use only original Bosch eBike batteries from the sys-
u
tem generation the smart system, which the manufac-
turer has approved for your eBike. Using other eBike
batteries can lead to injuries and pose a fire hazard.
Bosch accepts no liability or warranty claims if other
eBike batteries are used.
Note: The drive performance may be reduced when using
solely the PowerMore battery.
Switching on/off
Switching on the eBike battery is one way to switch on the
eBike. To do this, read and follow the instructions in the op-
erating manuals for the drive unit and operating unit.
Once the PowerMore battery is connected to the eBike via
the PowerMore cable, the eBike can be switched on/off via
the on/off button (5). Do not use any sharp or pointed ob-
jects to press the button.
To switch off the eBike battery, press the on/off button (5)
again. This will also switch the eBike off.
If no power is drawn from the drive for about 10 minutes
(e.g. because the eBike is not moving) and no button is
pressed on the on-board computer or the operating unit of
the eBike, the eBike will switch off automatically.
English – 3
0 275 007 3RE | (16.02.2023)
43