Sealey BSL105 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
1.1. GENERAL SAFETY
Carefully read these operating and safety instructions before using the boot tool. Keep them for future reference.
9
This tool should only be used by properly trained operators.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and or tie back long hair.
9
Keep children and unauthorised persons away from the working area.
9
Keep the boot tool away from fire, heat and chemicals.
9
DO NOT use the boot tool for any purpose other than that for which it is designed.
8
DO NOT operate the boot tool when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
‰
1.2. MECHANICAL SAFETY
Maintain the boot tool in good condition (use an authorised service agent).
9
If the tool falls or is knocked, stop operation and check for any damage i.e. cracked components.
9
DO NOT erase or damage any of the markings, symbols or text printed onto or moulded onto the surfaces of the boot tool.
8
In case of mechanical fault and/or breakage and/or cracks, immediately stop operation of the tool. Contact an authorised distributor.
9
DO NOT operate the boot tool if any parts are damaged or missing as this may cause failure and/or personal injury.
8
1.3. SPECIFIC SAFETY FOR CVJ TOOL
Only operate if trained to use pneumatic devices.
9
Air hoses are dangerous, observe manufacturer's safety guidelines.
9
Read these instructions and retain for future reference.
9
Ensure vehicle is correctly supported with road wheels secured, in line with manufactures guidelines.
9
Keep hands away from moving parts, wear safety gloves. Never insert fingers into the tool.
9
Never operate near the face, wear safety glasses.
9
Maximum safe operating pressure is 116psi(8bar). Fit a regulator to bring pressure within range.
9
A safety pressure valve is installed, when operational a 'leaking' sound will be heard from the piston.
9
Only use to fit stretchy CV boots. DO NOT use for any other purpose.
9
During expansion of the CV boot support the main body of the device with your free hand.
9
Store the device and operating instructions safely on the stand provided.
9
When operating the boot tool, to open a CV rubber boot, turn the tool away from your face and body.
9
Keep hands clear of the moving parts when operating the boot tool. Never insert fingers into the tool.
9
DO NOT point the boot tool at any person and/or towards any part of the operator's body.
8
2. INTRODUCTION
Installs CVJ boots without the need to remove the CV joint. Designed to be used in situ to the vehicle with up to 70% labour saving
costs. Innovative design provides easy operation with a single 2-way air switch, anti-slip grip, hand guard/belt hook, and anti-fatigue
features. One switch operation and airlock design allow airline detachment for safer no-trip installation. Suitable for cars, SUV's, 4x4's
and light commercial applications. Made in the UK with a 3-year guarantee included.
3. SPECIFICATION
Model No: .......................................................... BSL105
Air Inlet Size: ......................................................1/4"BSP
Max. Air Pressure: ....................................... 116psi(8bar)
Max. Joint Diameter: ........................................ Ø155mm
© Jack Sealey Limited
CVJ BOOT INSTALLER TOOL – AIR
MODEL NO:
Wear protective
gloves
Original Language Version
BSL105
BSL105 Issue 2 (S,3,4,F) 19/06/23