Advertisement
Quick Links
Seat Kit
Groundsmaster
Model No. 31980—Serial No. 400000000 and Up
Model No. 31981—Serial No. 400000000 and Up
Model No. 31982—Serial No. 400000000 and Up
Installation
1
Preparing the Machine
No Parts Required
Procedure
1.
Park the machine on a level surface.
2.
Engage the parking brake.
3.
Lower the cutting unit.
4.
Shut off the engine and remove the key.
5.
Disconnect the battery; refer to the electrical
system maintenance section of your Operator's
Manual.
2
Installing the Seat to the
Traction Unit
Parts needed for this procedure:
4
Bolt
8
Nut
1
Plate
1
Seat-switch wire harness
1
Air-ride-seat wire harness (Model No. 31982 only)
Positioning the Seat Assembly
1.
Remove the console from the seat base and
retain the nuts.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3200 or 3300 Series Traction Unit
Register at www.Toro.com.
Important:
Ensure that you support the
console after removing it so that it does not
crimp or hang by the cables and wires.
2.
Install the end of the seat-switch wire harness
labeled P2 (Seat Switch) to the seat-switch
connector under the seat.
3.
Align the seat studs with the holes in the seat
base
(Figure
1).
Figure 1
Model No. 31980 shown.
1. Seat
Original Instructions (EN)
All Rights Reserved *3434-642* A
Printed in the USA
Form No. 3434-642 Rev A
Installation Instructions
2. Seat base
g299316
Advertisement
Related Manuals for Toro 31980
Summary of Contents for Toro 31980
- Page 1 Form No. 3434-642 Rev A Seat Kit Groundsmaster ® 3200 or 3300 Series Traction Unit Model No. 31980—Serial No. 400000000 and Up Model No. 31981—Serial No. 400000000 and Up Model No. 31982—Serial No. 400000000 and Up Installation Instructions Installation Important:...
-
Page 2: Completing The Installation
Completing the Installation Use 4 nuts to secure the seat to the seat base Note: Model No. 31980 and 31981 are equipped with (Figure 1 wire harness (i.e., the seat-switch wire harness). Model No. 31982 is equipped with 2 wire harnesses (i.e., the seat-switch wire harness and the air-ride-seat... -
Page 3: Connect The Battery
Tighten the carriage bolt and nut, then tighten the existing nuts to the console studs. Secure the plate to the seat bracket with 3 carriage bolts and 3 nuts (B in Figure Connect the Battery No Parts Required Procedure Connect the battery; refer to the electrical system maintenance section of your Operator’s Manual. -
Page 4: Product Overview
Use the fore/aft adjustment lever to change the forward/rearward position of the seat. • Model No. 31980: Move the lever to the left (Figure 5), move the seat to a comfortable position, and release the locking lever to secure the position of the seat. - Page 5 Notes:...
- Page 6 Notes:...
- Page 7 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 8 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.