Table of Contents
Advertisement
Available languages
Available languages
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Mounting the Nose piece (Fig. D)
1. Select the correct nose piece for the rivet to be installed.
Refer to the number or letter
the Rivet Size Chart to select the proper nose piece for
the application.
2. Unscrew and remove the screw cap
3. Place the nose piece
4. Screw the screw cap onto the nose housing.
14
on the nose piece and
2
.
1
into the nose housing
Nose piece
A
B
Mandrel Collector and Spare Nose piece
Holder (Fig. E)
WARNING: Do not use the tool without the mandrel
collector attached.
The mandrel collector
attach to the rear of the tool.
The tool can be used without the spare nose piece holder.
To remove the mandrel collector or spare nose piece holder,
unscrew them until they are removed. If you are using the
tool with the spare nose piece holder, attach it to the tool
first, and then attach the mandrel collector.
Belt Clip (Fig. F)
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt clip is secure.
IMpoRTaNT: When attaching or replacing the belt clip
use only the screw
tighten screw.
If the belt clip is not desired at all, it can be removed from
the tool.
To remove the belt clip, remove the screw
belt clip in place.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. H)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
3
.
NoTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
Rivet Size Chart
Rivet Diameter
mm
DCF403
1
2.4
2
3.2
3
4.0
4
4.8
DCF414
4.8
6.0
C
6.4
and spare nose piece holder
5
20
that is provided. Be sure to securely
into the tool handle, align
11
ENGlIsh
Inches
3/32
1/8
5/32
3/16
3/16
15/64
1/4
6
19
,
20
that holds the
27
Advertisement
Table of Contents
